ISOM8711DFFR
Product Specifications
ISOM8711DFFR
Texas Instruments — Power Management & Signal Chain
Product Overview
The ISOM8711DFFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ISOM8711DFFR: single channel opto emulator with an open collector output
ISOM8711DFFR is a drop in replacement for a high speed digital optocoupler, with an emulated diode on the input side and an open collector output stage across a 3750 VRMS barrier in a five pin SOIC in a SOIC body of 5 pins. It reaches 25 Mbps, but only with at least 6 mA of input forward current: the recommended operating conditions print 5 Mbps between 2 mA and 3 mA, 10 Mbps between 3 mA and 6 mA and 25 Mbps at 6 mA and above. Propagation delay is 52 ns in the feature list and 54 ns in the switching table, pulse width distortion 17 ns in the feature list against 26 ns in the table, part to part skew 15 ns, and common mode transient immunity at least 125 kV per microsecond with 150 kV per microsecond typical. The barrier is rated 3750 VRMS with 500 VRMS of working voltage and up to 10 kV of surge.
Order code and package
| ISOM8711DFFR | SOIC DFF body, 5 pins, 3.51 mm by 7 mm, open collector output, 2000 pieces on a large reel, NIPDAU finish, moisture level 2 with a one year floor life, minus 40 to plus 125 degrees, marking 8711 |
| ISOM8711DFFR.A | the same reel on the re-released row, identical quantity, finish and moisture level |
| ISOM8710DFFR | the CMOS output version of the same part, same body, same reel, marking 8710. The input side is identical and the output stage is what changes |
| document scope | the datasheet covers the two output variants of one device family. There is no tube row, so every order is a 2000 piece reel |
Electrical parameters that decide the application
| Supply | 2.7 V to 5.5 V on the output side, so the part can sit on a 3.3 V or a 5 V rail and output the levels of that rail |
| Input side | a diode emulator rather than a logic input. It needs a forward current, with 2 mA printed as the minimum for operation and 0.8 V as the maximum off state voltage |
| Rate against drive current | 5 Mbps at 2 mA to 3 mA, 10 Mbps at 3 mA to 6 mA and 25 Mbps at 6 mA and above. The headline rate belongs to the top row of the table only |
| Output stage | open collector on this member, so it sinks current and does not source it. A pull up resistor sets the high level and the rise time |
| Output current | 13 mA of sink current at 0.6 V maximum low level, which is enough to drive an optocoupler style load or a logic gate with a resistor pull up |
| Propagation | 54 ns maximum in the switching table against 52 ns in the feature list, with a pulse width distortion of 26 ns maximum in the table against 17 ns in the feature list. The table is the conservative figure |
| Skew | 15 ns of part to part delay skew, which matters when several channels of the same signal have to arrive together |
| Common mode | at least 125 kV per microsecond with 150 kV per microsecond typical for a static low output, and a higher figure printed for a static high output |
| Isolation | 3750 VRMS for one minute per UL 1577, 500 VRMS of working voltage and up to 10 kV of surge, with the VDE, IEC 62368-1, 61010-1 and 60601-1 standards listed |
| Ageing | there is no light emitting diode to degrade, so the current transfer ratio that an optocoupler loses over life does not exist here. The vendor prints the absence of an ageing mechanism as the reason the input draws less current than an optocoupler |
| Package | five pin SOIC, 3.51 mm by 7 mm, pin compatible with common high speed digital optocouplers |
| Temperature | minus 40 to plus 125 degrees ambient and 130 degrees junction |
Family variants and how they differ
| 8711 against 8710 | open collector against CMOS. The open collector version fits a circuit that already pulls up to a rail and needs a wired or function, the CMOS version drives a push pull load without an external resistor |
| Against an optocoupler | the same footprint and the same input current range in most cases, with no ageing and a much smaller pulse width distortion. The input threshold is a diode emulator and not an LED, so the drive resistor has to be checked against the printed current, not against a transfer ratio |
| Against a digital isolator | an ISO67xx part takes a logic input and needs no drive current, is faster and has a lower propagation delay, but it comes in a different package and needs a supply on both sides. This part works from a single supply on the output side |
| Against a photovoltaic or a MOSFET output optocoupler | those are for switching a load, not for logic. This part sinks 13 mA and is a logic device |
| 3750 against 5000 VRMS | the barrier here is rated 3750 VRMS with 500 VRMS of working voltage, which is a lower class than the ISO67xx family. A mains referenced barrier usually needs the higher class |
Points to check before this part goes on a BOM
The data rate is a function of the drive current, and that is the single most important line on the page. At 2 mA the part is a 5 Mbps device, at 3 mA it is a 10 Mbps device and only at 6 mA and above does it reach 25 Mbps. A circuit that copied a 2 mA drive resistor from an optocoupler board will run at a fifth of the rate the headline suggests, and the symptom is a link that works at low duty cycle and corrupts at full speed.
The open collector output needs a pull up, and the pull up sets both the high level and the edge rate. The 15 ns rise and fall figures are measured with a 300 ohm load and 15 pF, so a 10 k pull up into a long trace turns a 54 ns propagation delay into a much slower edge. A customer who replaces an optocoupler with this part and keeps the old pull up value should check the edge on a scope before the board is released.
The two documents in the same file disagree on two numbers: the feature list prints 52 ns of propagation delay and 17 ns of pulse width distortion, while the switching table prints 54 ns and 26 ns. Both are inside the same revision, so the difference is a rounding or a condition rather than a change. Any timing budget should use the table figures, and a customer who quotes the feature list into a contract is quoting the optimistic number.
The working voltage of 500 VRMS is the isolation figure that matters for a continuous barrier, and it is far below the 5000 VRMS one minute rating of the isolated logic family. A product that puts this part across a mains referenced barrier is relying on a 500 VRMS working voltage, which many safety files will not accept even though the part carries a 3750 VRMS rating and the medical standard.
The drop in replacement claim is about the footprint and the pin functions, not about the surrounding circuit. The input is a diode emulator with a threshold that differs from an LED, the output stage has a different saturation voltage, and the propagation delay is a fraction of an optocoupler's. A board that swaps the part and changes nothing else will usually work, and the cases where it does not are the ones where the old optocoupler's slow, soft output was being used as a filter.
The reel is moisture level 2 with a one year floor life, so the same process rule as the isolated logic family applies. A five pin SOIC is small enough that a bake is cheap and a popcorning failure is expensive, and an assembly house that treats every isolator as level 1 will get this one wrong.
Why an opto emulator at all
An optocoupler's light emitting diode dims with age, so the current transfer ratio falls and a circuit that was built with margin at year one can fail at year ten. A capacitive emulator has no such mechanism, which is why the input current can be lower and the pulse width distortion smaller.
The other reason is speed. A high speed digital optocoupler at 25 Mbps is a expensive part with a wide spread of propagation delay, and the emulator brings that spread down to 15 ns part to part, which is what a parallel data path needs.
What the order code decides
The string reads ISOM871 for the family, 1 for the open collector output stage, DFF for the five pin SOIC body and R for the 2000 piece reel. The 0 in the same position is the CMOS output version, which is a different output stage in the same package.
Nothing in the string selects the data rate or the drive current, because both are set by the circuit around the part. The rate follows the forward current the board delivers, so the same reel can be a 5 Mbps part or a 25 Mbps part depending on one resistor.
Where this order code fits
Motor drives, industrial I/O modules, factory automation controllers and power supplies where a high speed digital optocoupler has to be replaced without changing the board, and where the ageing of an LED is a reliability concern. Teams comparing it with a neighbouring part start from our How to Verify a Drop in Replacement page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
Does it really run at 25 Mbps? Only with at least 6 mA of input forward current. At 2 mA to 3 mA the part is rated 5 Mbps and at 3 mA to 6 mA it is rated 10 Mbps.
What output stage does it have? Open collector, sinking 13 mA at 0.6 V maximum. It needs an external pull up, and the pull up value sets the high level and the edge rate.
Is it pin compatible with an optocoupler? Yes, the five pin SOIC footprint matches common high speed digital optocouplers. The input threshold and the output saturation are not identical, so the drive resistor and the pull up should be rechecked.
What is the working voltage? 500 VRMS, against a 3750 VRMS one minute rating and up to 10 kV of surge. A mains referenced barrier usually needs a higher working voltage class.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Obsolete Part Cross Reference Hub page sets out the checks that keep a substitute from failing on the bench.