Contact Us

ISOM8110DFGR

Brand: Texas Instruments
Texas Instruments ISOM8110DFGR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ISOM8110DFGR — Power Management & Signal Chain | Superb Automation

ISOM8110DFGR

Texas Instruments — Power Management & Signal Chain

Product Overview

The ISOM8110DFGR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

ISOM8110DFGR: A Phototransistor Optocoupler Footprint With an LED Emulator Inside

ISOM8110DFGR is a single-channel opto-emulator with an analog transistor output in a SOIC body of 4 pins. It drops into the pad of a standard phototransistor optocoupler and replaces the aging LED with a silicon emulator, at a current transfer ratio of 100 to 155 per cent and a 3750 VRMS barrier in this body.

Order code and package

Ordering stringISOM8110DFGR
PackageSOIC, 4 pins, DFG body, 2.54 mm pin pitch
CarrierTape and reel, 2000 pieces, 330 mm reel, 12.4 mm tape, pocket 8.0 by 3.8 by 2.7 mm, Q1
Sibling bodiesDFH and DFS are the 1.27 mm pitch versions at 5000 VRMS, DFH pockets 8.0 by 3.0 by 2.7 mm
Temperature rangeminus 55 to plus 125 degrees Celsius
InputLED emulator, current driven, 5 mA nominal test current
OutputNPN phototransistor equivalent, collector and emitter brought out
CTR grade100 to 155 per cent at 5 mA, the lowest of the four grades in the family

Electrical parameters that decide the application

Current transfer ratio at 5 mA, 5 V100 per cent minimum, 155 per cent maximum for the 8110 grade
Current transfer ratio at 0.5 mA, 5 V80 to 290 per cent, the same grade over a wider window at low current
Collector-emitter voltage80 V maximum
Input forward voltage at 5 mA1.2 V minimum, 1.4 V maximum
Input forward threshold current0.5 mA, below which the output is off
Collector-emitter saturation0.3 V at 20 mA input and 1 mA output
Collector dark current100 nA maximum
Input capacitance19 pF at 1 MHz
Response time3 microseconds typical at 10 V collector, 2 mA output, 100 ohm load
Isolation, DFG body3750 VRMS for 60 s per UL 1577, 707 VPK repetitive peak, 500 VRMS working, 5303 VPK transient
Isolation, DFH and DFS bodies5000 VRMS, 1061 VPK repetitive peak, 750 VRMS working, 7071 VPK transient, 10400 VPK surge
ClearanceAbove 5 mm on DFG, above 8 mm on DFH and DFS
Power dissipation150 mW on one body and 290 mW on the other, printed per package in the absolute maximum table

Family variants and how they differ

ISOM8110 and ISOM8115CTR 100 to 155 per cent, the 8115 is the bidirectional input version
ISOM8111 and ISOM8116CTR 150 to 230 per cent
ISOM8112 and ISOM8117CTR 255 to 380 per cent
ISOM8113 and ISOM8118CTR 375 to 560 per cent
Bidirectional inputThe 8115 to 8118 members accept a bidirectional DC input, the 8110 to 8113 are single polarity
Qualified versionsThe -Q1 strings are automotive, the -EP string is the enhanced product version
Pin functionAnode, cathode, emitter and collector, the same four pins as a phototransistor optocoupler

Points to check before this part goes on a BOM

CTR is graded in four bands and the band is part of the order code.A circuit built around a 100 to 155 per cent part will not necessarily work with a 375 to 560 per cent part, because the pull-up and the load resistor set the output current. Changing bands is a resistor change, and the band is visible in the seventh character of the string.

CTR falls at low input current, and the table shows by how much.At 5 mA the 8110 grade is held between 100 and 155 per cent. At 0.5 mA the same grade spreads from 80 to 290 per cent. A circuit that runs the input at 1 mA for power reasons is running outside the tight band and has to tolerate the wider window.

There is no LED to age.A phototransistor optocoupler loses CTR as the LED degrades, and the usual engineering rule is to allow 50 per cent degradation over life. This part has no LED, so the CTR printed at time zero is the CTR at end of life, which is the whole reason a control loop built on one can be built with a tighter gain margin.

The 3750 VRMS body is the 2.54 mm pitch one.DFG is 2.54 mm pitch at 3750 VRMS and 707 VPK repetitive peak. DFH and DFS are 1.27 mm pitch at 5000 VRMS and 1061 VPK. A drop-in replacement for an eight millimetre creepage optocoupler has to go to the narrow pitch body, not to DFG.

Response time is three microseconds at a 100 ohm load.That is faster than most phototransistor optocouplers at the same load, and it is what allows the part to be used in a feedback loop with a switching frequency in the hundreds of kilohertz rather than tens. The figure is load dependent and a 10 kohm pull-up slows it considerably.

Dark current and saturation are the two numbers that matter at the rails.100 nA of dark current means an off state is genuinely off at 125 degrees, and 0.3 V of saturation at 20 mA input means the output can pull a logic input to a valid low without a second transistor.

What a drop-in replacement has to keep

The four pins are anode, cathode, emitter and collector, and the pad geometry matches the industry standard 2.54 mm or 1.27 mm pitch body, which is why the part is described as pin to pin. What does not carry over automatically is the CTR band, so the resistor around the output has to be recalculated for the band on the new string.

The second item that does not carry over is the input drive. The emulator has a 1.2 V to 1.4 V forward voltage and a 0.5 mA threshold, so a driver sized for a 1.2 V LED works as is, while a driver that relied on the LED's dynamic resistance will see a slightly different current.

Where the isolation rating is set by the body, not the die

The same silicon is offered in a 3750 VRMS body and in a 5000 VRMS body, and the difference is the package spacing. Selecting the part on the die and then choosing the smaller body silently reduces the barrier from 707 to 1061 VPK working voltage the other way round, so the body code in the string is as important as the grade code.

Where this order code fits

Switch-mode supply feedback loops, motor drive interfaces and industrial I/O modules use this part where a phototransistor optocoupler is in the circuit and the CTR drift over life is what limits the loop margin. Teams comparing it with a neighbouring part start from our Pin to Pin Cross Reference page, and teams replacing a part that has gone end of life start from the Obsolete Part Cross Reference Hub page.

Questions buyers ask

Can ISOM8110DFGR replace a PC817 directly? The pin functions and the 2.54 mm pitch match, and the input is current driven in the same way, so the footprint works. The CTR band and therefore the output resistor have to be checked, because the bands differ between grades.

Does it need a series resistor on the input? Yes. The input is a current-driven emulator with a 1.2 V to 1.4 V forward voltage, so the current has to be set by a resistor exactly as it would be for an LED.

Why is the CTR higher at 0.5 mA than at 5 mA? It is not higher, it is wider. The guaranteed window at 5 mA is 100 to 155 per cent and at 0.5 mA it spreads from 80 to 290 per cent, so the typical value rises while the guaranteed band loosens.

What is the working voltage of the DFG body? 707 VPK repetitive peak and 500 VRMS working, against 1061 VPK and 750 VRMS on the 1.27 mm pitch bodies. The 3750 against 5000 VRMS headline follows the same split.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.