Contact Us

ISO7742FDWR

Brand: Texas Instruments
Texas Instruments ISO7742FDWR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ISO7742FDWR — Power Management & Signal Chain | Superb Automation

ISO7742FDWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The ISO7742FDWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

ISO7742FDWR: quad channel digital isolator split two forward and two reverse

ISO7742FDWR is a quad channel reinforced digital isolator with symmetric channels in a SOIC body of 16 pins. It carries four signals across a 5000 V RMS barrier with two channels in each direction, which suits two links that each need a command and a reply. The FDWR order code is the wide body 16-pin SOIC on a 2000 piece reel with the default low output.

Order code and package

Order codeISO7742FDWR
Package16-pin wide body SOIC, DW, 5000 V RMS
Packingtape and reel, 2000 pieces
Channelsfour, two forward and two reverse
Signalling rate100 Mbps
Isolation5000 V RMS, reinforced
Default stateoutput low, F suffix
Supply2.25 V to 5.5 V on each side

Electrical parameters that decide the application

Propagation delay10.7 ns typical at 5 V
Supply current1.5 mA per channel at 1 Mbps
Common mode transient immunity100 kV per microsecond typical
Surge capabilityup to 12.8 kV
Working voltage lifeover 30 years projected at 1500 V RMS
Temperature rangeminus 55 to plus 125 degrees

Family variants and how they differ

ISO7740four channels all forward
ISO7741three forward and one reverse
ISO7742two forward and two reverse, this order code
ISO7742FDWVeight pin wide body variant of the family

Points to check before this part goes on a BOM

Two channels each way fits two independent asynchronous links through one barrier: a pair of commands out and a pair of status lines back. It also fits a full duplex serial port where the transmit and the receive lines each need their own direction and there is one handshake line each way.

The symmetric split is what distinguishes it from the ISO7741, which has three forward and one reverse. On a board that needs two replies rather than three commands, the ISO7741 forces one reply through an external inverter or a second isolator, so the channel count has to be chosen from the protocol and not from the price.

The 5000 V RMS barrier belongs to the wide body package, and the reinforced classification is what allows the part to serve as the only barrier between a mains referenced circuit and a controller. A narrow body part in the same family is 3000 V RMS and is not a substitute where the standard asks for reinforced insulation.

Four channels at 100 Mbps is a lot of switching current on the isolated rail. At 1 Mbps the figure is 1.5 mA per channel, and a link that idles at 1 Mbps but bursts at 100 Mbps needs the rail sized for the burst, because the isolated supply has to deliver the peak and not the average.

The F suffix makes every output low when the input side loses power, which for two reply channels means both read as clear. Any protocol that treats a low level as a valid acknowledgement has to distinguish a real reply from a lost supply, and that distinction lives in the firmware timeout rather than in the isolator.

Ten point seven nanoseconds of delay and a channel to channel skew in the low nanoseconds allow the two forward channels to carry a clock and a data line whose timing relationship survives the barrier. A source synchronous link that relies on that relationship has to check the skew across temperature, not only at 25 degrees.

Temperature range reaches minus 55 degrees and the working voltage life is projected at 1500 V RMS over 30 years. Neither of those covers a continuous 5000 V RMS, which is a one minute withstand test, so a customer who plans a 3 kV working voltage is outside the family's projected life.

Two links through one barrier share a supply and a ground on each side, so a fault that pulls one side down takes both links with it. Where the two links serve redundant channels, the shared barrier defeats the redundancy, and two separate isolators are the correct choice even though the quad part is cheaper.

The packaging suffix identifies the reel and the body, and the FD combination identifies both the default state and the channel arrangement. Reading the code from the end is a common source of ordering errors in this family, because the letters after the number carry the electrical behaviour and not the packing.

A symmetric channel split is the right shape for two independent links but the wrong shape for one link that needs three control lines. Choosing the part by pin count alone leads to an inverted signal or an extra isolator on the board, and the cost of that mistake is larger than the difference between the two order codes. The protocol decides the channel map first.

Where this order code fits

It is used for isolated dual serial ports, two axis drive interfaces, redundant sensor links and any board that needs two commands and two replies across one reinforced barrier. Teams comparing it with a neighbouring part start from our CAN Bus Transceiver Selection page, and teams replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.

Questions buyers ask

What is the difference from the ISO7741? Channel direction. This part is two forward and two reverse, the ISO7741 is three forward and one reverse, and the pinout is the same family.

Can it carry a clock and data pair? Yes, with the channel to channel skew as the limit rather than the 100 Mbps rate.

Does it include an isolated supply? No. The barrier isolates signals only, so the second side needs its own rail.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.