Contact Us

ISO7741FQDBQRQ1

Brand: Texas Instruments
Texas Instruments ISO7741FQDBQRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ISO7741FQDBQRQ1 — Power Management & Signal Chain | Superb Automation

ISO7741FQDBQRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The ISO7741FQDBQRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

ISO7741FQDBQRQ1: automotive quad isolator at 100 Mbps with three forward channels

ISO7741FQDBQRQ1 is four logic channels across a barrier in a 16 pin QSOP, three in the forward direction and one back, with a low default state and an automotive qualification carried in a separate vendor document in a QSOP body of 16 pins. The family runs at 100 Mbps with supplies from 2.25 V to 5.5 V on both sides, 1.5 mA per channel at 1 Mbps, a propagation delay of 17 ns maximum with 5 V supplies, and plus or minus 100 kV per microsecond of common mode transient immunity typical. It is characterised from minus 55 to plus 125 degrees. The body on this page is the QSOP, and its isolation figures are much lower than the wide SOIC: 566 VPK of repetitive peak voltage, 400 VRMS of working voltage, 4242 VPK transient, 5000 VPK of impulse and 3.7 mm of clearance.

Order code and package

ISO7741FQDBQRQ1automotive string, three forward channels and one reverse, default low, DBQ body, 16 pins. The document used for this page prints the industrial strings and names ISO7740-Q1, ISO7741-Q1 and ISO7742-Q1 as separate automotive versions, so the packing and the marking for the Q1 row were left unconfirmed rather than copied from an industrial row
ISO7741FDBQRthe industrial version of the same channel split and the same body, 2500 pieces on a large reel, NIPDAU finish, moisture level 2 with a one year floor life, minus 55 to plus 125 degrees, marking 7741F
ISO7741DBQRthe default high version, same body and same reel, marking 7741
ISO7741FDWRthe wide body SOIC version, 2000 pieces on a large reel, which carries 2121 VPK of repetitive peak voltage against 566 VPK here
ISO7741BDWRthe basic isolation version of the wide body part, 1414 VPK of repetitive peak voltage and 1000 VRMS of working voltage

Electrical parameters that decide the application

Rate100 Mbps per channel, the fastest member of the isolated logic line and the one used where a fast SPI clock or a parallel bus has to cross a barrier
Supplies2.25 V to 5.5 V on each side with level translation between them, so a 2.5 V side and a 5 V side can share one package
Channel splitthree forward and one reverse. That is the isolated SPI pattern, where clock, data and chip select go forward and the return data comes back
Default statethe F suffix sets the output low on a loss of input power or signal. The missing F sets it high, which is right for an active low enable
Current1.5 mA per channel at 1 Mbps, which is slightly lower than the 674x family at the same rate
Propagation17 ns maximum with 5 V supplies. The table prints 12.7 ns typical while the feature list prints 10.7 ns, so any timing budget should use the maximum rather than either typical figure
Enable timingthe disable path is printed in nanoseconds, 20 ns maximum, while the enable path is printed in microseconds, 8.5 microseconds maximum on the F suffix member. A channel that is parked and then enabled costs more than one frame at a fast clock
Protectionplus or minus 8 kV IEC 61000-4-2 contact discharge across the barrier at system level, which is a board number and not a pin rating
Isolation on this body566 VPK repetitive peak, 400 VRMS working voltage, 4242 VPK transient, 5000 VPK impulse, 10000 VPK surge and 3.7 mm of clearance and creepage, with more than 17 um of insulation thickness
Isolation on the wide body2121 VPK repetitive peak, 1500 VRMS working voltage, 8000 VPK transient, 8000 VPK impulse, 12800 VPK surge and more than 8 mm of clearance, which is the version to compare against when the board has room
Certificationsup to 5000 VRMS per UL 1577 for the family, DIN EN IEC 60747-17 for the VDE file and the IEC 62368-1, 61010-1 and 60601-1 standards
Temperatureminus 55 to plus 125 degrees, which is ten degrees wider at the cold end than the 674x family and the reason it appears in outdoor and under bonnet equipment

Family variants and how they differ

DBQ against DWthe same die in two bodies. The QSOP is 4.90 mm by 6.0 mm and gives 3.7 mm of clearance and 566 VPK of repetitive peak voltage. The wide SOIC is 10.30 mm by 7.50 mm and gives 8 mm and 2121 VPK. Choosing the small body is choosing a lower barrier
7741 against 7740 and 7742all four forward, three forward and one back, or two each way. The 7741 is the isolated SPI split and the most common of the three
F against no Fthe default state on power loss. The F is the safe choice for a gate drive or a chip select, the non F for an active low enable
B against the standard stringthe B version is the basic barrier at 1414 VPK and 1000 VRMS working voltage, for a product whose safety file accepts basic isolation
Against an optocoupleran optocoupler at 100 Mbps does not exist in a single channel at a sensible price, and it ages. The capacitive part is faster and does not age, but it needs a supply on both sides

Points to check before this part goes on a BOM

The QSOP body is the reason to read this page carefully. Its repetitive peak voltage is 566 VPK against 2121 VPK on the wide body, its working voltage is 400 VRMS against 1500 VRMS, and its clearance is 3.7 mm against more than 8 mm. A product that picks the small body for board area and then claims the wide body isolation figure in its safety file has a problem that no amount of testing will fix, because the package is the barrier.

The Q1 string on this page is an automotive grade, and the document in hand does not print its reel, its marking or its moisture level. The industrial DBQ rows show 2500 pieces on a large reel at minus 55 to plus 125 degrees, and those figures cannot be carried across to a Q1 body as a promise. A quotation for the automotive string should state the packing as confirmed at order time.

The propagation delay has three different numbers in one document: 10.7 ns typical in the feature list, 12.7 ns typical in the switching table and 17 ns maximum. The difference between the two typicals is the supply and temperature condition behind each one, and the only figure that is safe in a timing budget is the maximum. A controller that samples at a fixed delay from the clock edge should be checked against 17 ns, not against the headline.

The enable path on this family is measured in microseconds while the disable path is measured in nanoseconds. Parking a channel is fast, waking it is not. In an isolated SPI port where the chip select is used to frame a transfer, an enable delay of 8.5 microseconds can swallow the first byte, and the usual fix is to leave the channel enabled and frame with the signal itself.

The family carries minus 55 to plus 125 degrees, which is wider at the cold end than most industrial isolators. That matters for equipment that starts in an unheated enclosure or on a vehicle, and it is one of the few real differences between this family and the 674x line at the same channel count.

An isolator separates signals and not power. Each side needs its own rail, and the isolated side usually needs a small converter. On an automotive board the isolated side is often a different ground domain rather than a safety barrier, which changes the certification argument but not the need for a separate supply.

Where 100 Mbps and three forward channels meet

An isolated SPI port at a 20 MHz clock needs the clock, the data out and the chip select to cross one way and the data in to come back, which is exactly the 7741 split. A fast ADC interface or a digital position sensor with a serial output uses the same pattern.

The 100 Mbps ceiling is there for the clock edge rather than for the average rate, because a square wave at 20 MHz needs the harmonics, and a slower isolator rounds the edges until the receiver at the far end samples the wrong level.

What the order code decides

The string reads ISO7741 for the channel split, F for the default low state, Q for the automotive grade, DBQ for the QSOP body and R for the reel. The Q and the DBQ together are what make this string different from the industrial row next to it in the same table, and both have to be confirmed before a quotation goes out.

The B in ISO7741B is the basic barrier and sits in a different position in the string, so a part number that mixes B and Q does not exist. Reading the string character by character is the only reliable way to know which barrier and which qualification a reel carries.

Where this order code fits

Isolated SPI and ADC links in automotive and industrial control, motor drive signal paths and any board where a fast serial bus has to cross a barrier with three signals forward and one back. Teams comparing it with a neighbouring part start from our Pin to Pin Cross Reference page, and teams replacing a part that has gone end of life start from the Date Code Management page.

Questions buyers ask

Why is the isolation lower on this body? The QSOP is 4.90 mm by 6.0 mm with 3.7 mm of clearance, so it gives 566 VPK of repetitive peak voltage and 400 VRMS of working voltage. The wide SOIC gives 2121 VPK and 1500 VRMS at more than 8 mm.

Is the automotive reel printed in this document? No. The addendum lists industrial rows and names ISO7740-Q1, ISO7741-Q1 and ISO7742-Q1 as separate versions, so the Q1 packing has to be confirmed separately.

What is the maximum propagation delay? 17 ns with 5 V supplies on both sides. The feature list quotes 10.7 ns typical and the table 12.7 ns typical, so a timing budget should use the maximum.

How long does a channel take to enable? 8.5 microseconds maximum on the F suffix member, against 20 ns to disable. Parking a channel is fast, waking it is not.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.