ISO7731FQDBQRQ1
Product Specifications
ISO7731FQDBQRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The ISO7731FQDBQRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ISO7731FQDBQRQ1: Two Lines Out and One Back Across a Barrier Rated for 3000 VRMS
ISO7731FQDBQRQ1 is an automotive qualified triple channel digital isolator in a SSOP (DBQ) body of 16 pins. It passes two channels from the controller side to the isolated side and one channel back, at 100 Mbps per channel, with an 11 ns typical propagation delay on 5 V supplies and a default output that falls low when input power is lost. The small DBQ body carries a 3000 VRMS rating rather than the 5000 VRMS of its wide body sibling, which is the first thing to settle before this string goes on a BOM.
Order code and package
| Ordering string | ISO7731FQDBQRQ1 |
| Family | ISO773x-Q1, the automotive triple channel family in document SLLSEU3F |
| Qualification | AEC-Q100 grade 1, minus 40 to plus 125 degrees ambient |
| Package | SSOP, DBQ body, 16 pins, 4.90 mm by 3.90 mm nominal |
| Reel and packing | 2500 pieces on a large reel, NiPdAu lead finish |
| Moisture level | Level 2, 260 C peak, one year floor life |
| Same die in the wide body | ISO7731FQDWRQ1 in SOIC DW, 16 pins, 2000 pieces on a large reel |
| Channel arrangement | Two channels forward and one reverse |
| Default state | The F suffix means the output falls low when the input power or the input signal is lost |
| Isolation in this body | 3000 VRMS per UL 1577, 4242 VPK transient, 566 VPK repetitive peak |
| Enable pins | One enable per output side, used to put the outputs in high impedance |
Electrical parameters that decide the application
| Data rate | 100 Mbps per channel |
| Propagation delay | 11 ns typical and 17 ns maximum with both supplies at 5 V |
| Pulse width distortion | 0.6 ns typical, 5.9 ns maximum |
| Channel to channel skew | 1.3 ns typical and 4 ns maximum on channels running the same direction |
| Part to part skew | 4.5 ns maximum, which is the figure that matters when two packages sit in parallel |
| Supply range | 2.25 to 5.5 V on each side, with level translation between the two rails |
| Quiescent current | 1.5 mA per channel typical at 1 Mbps |
| Common mode transient immunity | Plus or minus 100 kV per microsecond typical |
| Surge | Up to 12.8 kV peak in the wide body and 10 kV peak in this body |
| ESD across the barrier | Plus or minus 8 kV contact discharge per IEC 61000-4-2 |
| Working voltage | 1500 VRMS with a projected lifetime above thirty years, quoted for the wide body |
| Certification set | VDE 0884-17, UL 1577, IEC 61010-1, IEC 62368-1, IEC 60601-1 and GB 4943.1 |
Family variants and how they differ
| ISO7730QDBQRQ1 | All three channels forward with a high default, for three signals leaving the controller |
| ISO7730FQDBQRQ1 | All three channels forward with a low default |
| ISO7731QDBQRQ1 | The same two forward one reverse arrangement with a high default instead of low |
| ISO7731FQDWRQ1 | The wide body version, 5000 VRMS and 2121 VPK working voltage, 2000 pieces on a reel |
| ISO774x family | Four channels at the same 100 Mbps when a fourth line has to cross the barrier |
| ISO6721 | A 50 Mbps dual for a slower bus that does not need the 100 Mbps front end |
| ISO1042 | An isolated CAN FD transceiver when the far side is a bus rather than a logic line |
Points to check before this part goes on a BOM
The body decides the isolation rating, not the part number prefix. The DBQ body is rated 3000 VRMS with a 4242 VPK transient and 566 VPK repetitive peak, while the DW body of the same die carries 5000 VRMS, 8000 VPK and 2121 VPK. A board that needs reinforced working voltage above 566 VPK cannot use this string at all, and a substitution from DW to DBQ late in a programme changes the safety case.
The default state is the whole point of the F suffix, and it is easy to order the wrong one. With F, a lost input supply pulls the output low. Without it, the output goes high. On a gate drive enable or a chip select that difference decides whether a power loss leaves the far side enabled, so the suffix has to match the fail safe direction the system expects, not the catalogue line that happens to be in stock.
The 100 Mbps figure is a channel figure and the delay budget has to be built from the maximum. At 5 V the part is specified at 17 ns maximum rising and the same falling, before the cable, the connector and the receiver are counted. A loop that goes out through one channel and back through the reverse channel carries two of those delays plus the skew between them.
There is no 1.8 V support on either side. The recommended range starts at 2.25 V, so a 1.8 V processor has to be buffered to a 2.5 V or 3.3 V rail first, and the level translation the family advertises happens between rails that are both above that floor.
The enable pins are not a power down path. They put the outputs into high impedance and reduce current, but the input side keeps drawing, and a channel that is enabled while its far rail is still rising can pass a short pulse. Systems that need a clean start sequence should hold the enable low until both rails are in regulation.
Where the three channels sit in a motor drive
A three phase inverter card usually has one controller ground and one power ground, and the signals that cross are the three gate commands, the fault return line and the current sense ready signal. Two forward channels carry the two gate commands that have no local equivalent, and the reverse channel carries the fault line back, which is the arrangement this string provides without leaving a channel unused.
The enable pin on each side is what makes the part usable during a controller reset. Driving the input side enable low places the outputs in high impedance, so the gate driver on the far side sees a defined state from its own pull resistors instead of a floating input while the controller reboots. That behaviour has to be checked against the gate driver input thresholds, since a high impedance node with weak pull resistors can sit in the linear region.
What the small body costs on a real board
The DBQ body is 4.90 mm by 3.90 mm against 10.30 mm by 7.50 mm for the wide body, which is roughly a quarter of the footprint, and it removes the creepage problem that a wide body creates on a dense card. The price is the isolation rating: 3000 VRMS against 5000 VRMS and 566 VPK working against 2121 VPK.
For a 48 V or 60 V motor bus with a functional barrier, the small body is enough and the space saving is real. For a barrier that has to hold a mains referenced measurement side away from a user accessible side, the wide body is the only one of the two that carries the reinforced working voltage, and the footprint has to be found elsewhere.
Where this order code fits
The part is chosen where a controller has to talk to a floating section with two signals going out and one coming back, and the barrier only has to carry functional isolation rather than a mains rating. Teams comparing it with a neighbouring part start from our Pin to Pin Cross Reference page, and teams replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.
Questions buyers ask
Can the DBQ string replace the DW string on an existing board? Electrically it is the same die and the same channel arrangement, but the isolation ratings drop to 3000 VRMS, 4242 VPK transient and 566 VPK repetitive peak. The footprint is smaller, so a board change is needed anyway, and the safety case has to be rechecked against the lower working voltage before the swap is accepted.
What happens to the outputs when the controller side loses power? With the F suffix the outputs fall low and stay there while the isolated side keeps its rail. Without the suffix they go high. Either way the far side is driven to a defined level rather than floating, which is why the default state has to match the fail safe direction of the load.
Does the part need an isolated supply on the far side? Yes. Both sides need their own rail between 2.25 and 5.5 V, and the far side normally needs an isolated converter or a bootstrap winding to feed it. The isolator passes signals, not power, and the 1.5 mA per channel figure only covers the isolator itself.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.