ISO7141CCDBQR
Product Specifications
ISO7141CCDBQR
Texas Instruments — Power Management & Signal Chain
Product Overview
The ISO7141CCDBQR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ISO7141CCDBQR: quad-channel digital isolator at 50 Mbps with three forward and one reverse channel
ISO7141CCDBQR is a four-channel digital isolator in a small QSOP body with three channels one way and one the other in a QSOP body of 16 pins. The 7141 channel arrangement is three forward and one reverse, which matches a controller talking to a peripheral over a four wire interface where the peripheral answers on a single line. It signals at 50 Mbps on 5 V supplies, propagates in 23 nanoseconds typical, and isolates to 4242 V peak with a 566 V peak working voltage.
Order code and package
| Order code | ISO7141CCDBQR |
| Function | quad-channel digital isolator |
| Package | QSOP, 16 pins, DBQ body |
| Channels | four, three forward and one reverse |
| Signaling rate | 50 Mbps with 5 V supplies |
| Propagation delay | 23 nanoseconds typical at 3.3 V |
| Default output | high on this code, the F suffix version defaults low |
| Supply current | 1.3 milliamps per channel at 1 Mbps, 2.6 milliamps at 25 Mbps, 3.3 V |
| Supply range | 2.7 V, 3.3 V and 5 V |
| Isolation | 4242 V peak per VDE V 0884-10, 566 V peak working voltage |
| UL rating | 2500 V RMS for one minute |
| Transient immunity | 50 kV per microsecond typical |
| Temperature range | minus 40 to plus 125 C |
Electrical parameters that decide the application
| Barrier | silicon dioxide |
| Noise filter | integrated filter on the inputs |
| Level translation | any supply combination from 2.7 V to 5 V on either side |
| Certifications | VDE V 0884-10, UL 1577, CSA notice 5A, IEC 60950-1, IEC 61010-1, CQC GB 4943.1 |
| Channel direction | three forward, one reverse, fixed in silicon |
| Body size | QSOP, smaller than the wide SOIC used by the higher isolation parts |
| Output drive | CMOS push pull, no external buffer needed at these rates |
| Lifetime | silicon dioxide barrier, long life at the rated working voltage |
Points to check before this part goes on a BOM
The channel mix is the first thing to check against the interface. Three forward and one reverse suits SPI with a single data return line, and a board that needs two returns has to move to a different arrangement rather than turning a channel around in the symbol.
The working voltage of 566 V peak is a basic insulation number, not a mains barrier rating. On a 400 V DC bus it is adequate for functional isolation, and on a mains connected front end the part with the higher working voltage is the one the safety file will accept.
Fifty megabits per second is available on 5 V supplies and drops with the supply, which matters when a 3.3 V board is pushed to its limit. The propagation delay also moves with the supply, so a timing budget built at 5 V should be rechecked at 3.3 V.
The default output state matters at power up. This code drives high with the input undriven; the F version drives low. A gate signal or a chip select that must be inactive during power up should be assigned to the version whose default state is the safe one, rather than fixed with a pull resistor on the isolated side.
Where this order code fits
Motor control interface cards, isolated SPI ports and industrial IO boards order this code when four signals have to cross one barrier in a body smaller than a wide SOIC. Boards comparing it with a neighbouring part start from our Power Management Cross Reference page, and boards replacing a part that has gone end of life start from the BOM Consolidation page.
Questions buyers ask
Can the two sides run at different voltages? Yes, from 2.7 V to 5 V independently on each side, with level translation in both directions.
Is this part suitable for a mains barrier? It is rated for basic insulation at 566 V peak working voltage, which is a functional or basic rating for many industrial rails and not a reinforced mains rating.
SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Vendor Consolidation page sets out the checks that keep a substitute from failing on the bench.