Contact Us

ISO7041FDBQR

Brand: Texas Instruments
Texas Instruments ISO7041FDBQR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ISO7041FDBQR — Power Management & Signal Chain | Superb Automation

ISO7041FDBQR

Texas Instruments — Power Management & Signal Chain

Product Overview

The ISO7041FDBQR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

ISO7041FDBQR: A Four-Channel Isolator That Runs on Microamps

ISO7041FDBQR is an ultra-low power four-channel digital isolator in a QSOP body of 16 pins. Three channels forward and one back, a 4 Mbps ceiling, and a quiescent current of 3.5 microamps per channel at 3.3 V, which is what allows it to sit inside a loop-powered transmitter.

Order code and package

Ordering stringISO7041FDBQR
PackageQSOP, 16 pins, DBQ body
CarrierTape and reel, 330 mm reel, 12.4 mm tape, pocket 6.4 by 5.2 by 2.1 mm, Q1
Supplies1.71 V to 1.89 V, or 2.25 V to 5.5 V, each side independent
Temperature rangeminus 55 to plus 105 degrees at 1.8 V, minus 55 to plus 125 degrees at 2.25 V to 5.5 V
Channel directionThree forward, one reverse
Default stateOutput low, the F string, the plain string defaults high

Electrical parameters that decide the application

Signaling rateUp to 4 Mbps
Quiescent current per channel3.5 microamps at 3.3 V
Current per channel at 100 kbps15 microamps at 3.3 V
Current per channel at 1 Mbps116 microamps at 3.3 V
Dynamic currentUnder 120 microamps per Mbps per channel
Propagation delay140 ns typical, 175 ns maximum
Propagation delay drift15 picoseconds per degree Celsius
Minimum pulse width250 ns
Pulse width distortion10 ns
Channel-to-channel skew10 ns for same-direction and 10 ns for opposite-direction channels
Part-to-part skew70 ns
Isolation rating3000 VRMS per UL 1577
Projected lifetimeAbove 100 years
Common-mode transient immunityplus or minus 100 kV per microsecond typical
System-level ESDPlus or minus 8 kV IEC 61000-4-2 contact across the barrier

Family variants and how they differ

ISO7041Four channels, three forward and one reverse, default high, the plain string
ISO7041FThe same channels with a low default, the part on this page
Refresh modeThe part can run with the periodic refresh enabled or disabled, and the current tables print both
Refresh disabled behaviourLower static current, but a steady-state DC input is not re-sampled, so the state has to be held by the input
Refresh enabled behaviourThe state is refreshed periodically, at the cost of a few microamps per channel
Automotive versionISO7041-Q1 is listed as another qualified version
Power classThe lowest current member of the isolator range, chosen against the 100 Mbps family at 1.5 mA per channel

Points to check before this part goes on a BOM

3.5 microamps per channel is what fits a 4 to 20 mA loop.A loop-powered transmitter has about 3.5 mA of total budget and the loop current must stay above 3.8 mA at the bottom of the range. Four channels at 3.5 microamps each is 14 microamps, which is noise against that budget, and it is the reason this part exists at all.

Refresh mode is a choice with a current cost.With the refresh disabled the static current is at its lowest, but a steady DC input is not re-sampled by the barrier, so the input has to hold the level. With the refresh enabled the state is re-sent periodically for a few microamps, which is the right choice for a signal that can float or for a line that drives a latch.

4 Mbps is a ceiling, not a target.The 140 ns typical delay and 250 ns minimum pulse width put the part at the low end of the isolator range. It suits a 1 Mbps UART, a 100 kHz SPI clock or a set of slow GPIO, and it is the wrong part for anything that needs a 10 MHz clock.

The temperature window depends on the supply.At 1.8 V the part is specified to plus 105 degrees and at 2.25 V to 5.5 V to plus 125. A 1.8 V rail in a hot cabinet is therefore 20 degrees short of what the same part achieves at 3.3 V, which is easy to miss when the rail is chosen for logic compatibility.

3000 VRMS is the barrier here.There is no 5000 VRMS option in this family. A loop-powered transmitter needs functional isolation against the loop, not a reinforced barrier, so the 3000 VRMS rating is the working point rather than a compromise.

The F suffix again changes the failure state.Three forward channels default low means a lost input side reads as three low signals. In a transmitter, a low on an enable line is the safe state, so the F string is the usual choice for that application.

Where microamp isolation changes a product

A field transmitter that has to pass a 3.8 mA low alarm has no room for an isolator that draws milliamps. This part lets the microcontroller and the barrier share the loop current, which removes the separate isolated supply that a conventional isolator would need.

The same argument applies to a battery-powered sensor node that has to run for years: 14 microamps of quiescent current is below the self-discharge of most cells, so the isolator stops being the item that sets the battery life.

Reading the refresh tables without a mistake

The supply current tables print quiescent, 10 kbps, 100 kbps and 1 Mbps rows with the refresh enabled and disabled, for side 1 and side 2 separately and then combined per channel. The combined per-channel row is the one to use for a rail calculation, because the two sides are fed from different supplies and only the combined figure tells you the total the isolated winding has to deliver.

The rows with the refresh disabled are the lowest numbers in the document and the easiest to quote by accident. They do not apply to a signal that has to be re-sampled, so a rail sized from them will sag when the refresh is enabled.

Why the minimum pulse width is 250 ns

The part uses an edge-based modulation with a periodic refresh instead of a continuous carrier, so a pulse shorter than the 250 ns minimum can be lost entirely rather than merely delayed. At a 1 Mbps UART rate the bit is a microsecond and the margin is comfortable, while a 4 Mbps stream with a 250 ns bit sits exactly on the limit.

That is the practical reason the datasheet ceiling of 4 Mbps should be treated as a burst rate. A protocol with a long run of identical bits is fine, because the refresh carries the level, and a protocol with a stream of short opposite transitions is the case that has to be measured on the bench.

Where this order code fits

Loop-powered 4 to 20 mA transmitters, battery sensor nodes and low-power GPIO isolation use this part where the current budget is measured in microamps and the data rate is under a few megabits. Teams comparing it with a neighbouring part start from our Pin to Pin Cross Reference page, and teams replacing a part that has gone end of life start from the Incoming Inspection Plan page.

Questions buyers ask

How low is the current really? 3.5 microamps per channel quiescent at 3.3 V, 15 microamps per channel at 100 kbps and 116 microamps per channel at 1 Mbps. The dynamic term is under 120 microamps per Mbps per channel.

Can it carry a 10 MHz SPI clock? No. The ceiling is 4 Mbps and the minimum pulse width is 250 ns, so a clock above a few megahertz will be distorted. The 100 Mbps family is the one for that.

What does the F in ISO7041FDBQR change? The default output state, low instead of high, when the input side loses power or signal. The channels, the rate and the current are unchanged.

Why does the temperature range change with the supply? The device is specified to plus 105 degrees at 1.71 V to 1.89 V and to plus 125 degrees at 2.25 V to 5.5 V, so the rail choice sets the ambient limit.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.