Contact Us

ISO6740DWR

Brand: Texas Instruments
Texas Instruments ISO6740DWR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ISO6740DWR — Power Management & Signal Chain | Superb Automation

ISO6740DWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The ISO6740DWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

ISO6740DWR: Four Channels in One Direction Across a 5000 VRMS Barrier

ISO6740DWR is a quad-channel reinforced digital isolator in a SOIC body of 16 pins. All four channels face the same way, the default output is high, and the barrier is rated to 5000 VRMS with a 1500 VRMS working voltage and an 11 ns typical delay.

Order code and package

Ordering stringISO6740DWR
PackageSOIC, 16 pins, DW body
CarrierTape and reel, 2000 pieces, 330 mm reel, 16.4 mm tape, pocket 10.75 by 10.7 by 2.7 mm, Q1
Supplies1.71 V to 1.89 V and 2.25 V to 5.5 V, each side independent
Temperature rangeminus 40 to plus 125 degrees Celsius
Channel directionFour forward, none reverse
Default stateOutput high on loss of input power or input signal, the F suffix version defaults low
Enable pinsPer-side enable, outputs go high impedance

Electrical parameters that decide the application

Data rate50 Mbps
Isolation rating5000 VRMS per UL 1577
Working voltage1500 VRMS, quoted with a projected lifetime above 30 years in the family description
Transient isolation voltage7071 VPK
Surge isolation voltage10000 VPK
Common-mode transient immunityplus or minus 150 kV per microsecond typical, 100 kV per microsecond minimum
Propagation delay at 5 V and 3.3 V11 ns typical, 18 ns maximum at 100 kbps
Propagation delay at 2.5 V12 ns typical, 20.5 ns maximum
Channel-to-channel skew0.2 ns typical at 5 V, 0.5 ns at 3.3 V, 7 ns maximum
Part-to-part skew6 ns at 5 V and 7 ns at 3.3 V
Output rise and fall2.6 ns typical at 5 V, 1.6 ns at 3.3 V, 4.5 ns and 3.2 ns maximum
Supply current1.6 mA per channel typical at 1 Mbps
Clearance and creepageAbove 8 mm external, internal gap above 17 micrometres, tracking index above 600 V
System-level ESDPlus or minus 8 kV IEC 61000-4-2 contact across the barrier

Family variants and how they differ

ISO6740Four forward channels, default high, the part on this page
ISO6740FFour forward channels, default low
ISO6741Three forward and one reverse, default high
ISO6742Two forward and two reverse, default high
Qualified versionsISO6740-Q1, ISO6741-Q1 and ISO6742-Q1 are the automotive members, printed as separate strings in the addendum
Supply options1.71 V to 1.89 V on a side, or 2.25 V to 5.5 V, mixed freely between the two sides
Enable behaviourEnable pins put the outputs in high impedance for multi-master driving

Points to check before this part goes on a BOM

Default state decides what happens at power-down.With four forward channels, the default high version holds every output high when the input side loses power, and the F version holds them low. In a system where a high level enables a driver, the F version is the safe choice, and where a high level means a healthy signal, the plain version is. The choice is made at the ordering string, not at the board.

The 11 ns delay is quoted at three supply voltages.The switching tables give 11 ns typical and 18 ns maximum at both 5 V and 3.3 V, and 12 ns typical with 20.5 ns maximum at 2.5 V. A timing budget built on the 5 V row will be 2.5 ns optimistic if the isolated side runs from 2.5 V, which is enough to matter at 50 Mbps.

Channel-to-channel skew is the figure that sets parallel bus timing.0.2 ns typical at 5 V and 7 ns maximum across the four channels is what allows a four-bit parallel word to cross the barrier and still arrive inside one sampling window. The maximum, not the typical, has to be used for a bus that runs at temperature.

1.6 mA per channel is a 1 Mbps figure.The current rises with the toggle rate, and the family quotes the figure at 1 Mbps. At 50 Mbps the current per channel is far higher and the isolated supply has to be sized from the switching current table rather than from the headline number.

10000 VPK surge is a package statement.The surge figure is measured in oil on the barrier itself. It says the insulation survives a lightning-class transient, and it says nothing about the clearance on the board around the part, which is where a real surge will flash over first if the pads are close.

The Q1 strings are separate order codes.The addendum lists ISO6740-Q1 as another qualified version rather than as a suffix on this row. A purchase order that needs the automotive part has to carry the Q1 string, and the reel, grade and marking for it are not printed in this industrial document.

Where four forward channels are the right shape

A controller that drives four isolated gate drivers, four solid-state relays or four sensor interface lines in one direction only needs no reverse channel, and the ISO6740 puts all four in that direction. The alternative, a two-and-two part, wastes two channels and costs the same board area.

Four forward channels with a common enable also allow a single fault signal to turn the whole group off, which is what a safety output module does when the watchdog fires.

Reading the supply current tables before sizing the isolated rail

The document gives supply current per side with the inputs static and with them switching, at 1 Mbps, 10 Mbps and 50 Mbps. A rail sized from the static row will brown out the moment the bus starts toggling, because the dynamic current at 50 Mbps is an order of magnitude above the quiescent figure.

The isolated supply also has to hold through the enable transition, when all four outputs change state at once and the current step is the sum of four channels.

What the enable pins allow on a shared bus

Each side has an enable, and pulling it takes that side's outputs to high impedance. On a backplane where two controllers can both drive a four-bit bus, the enables are what allows one to take over without contention, and the transition is specified rather than left to whatever the output stage does.

The enable is also a power lever. A group that is not being used can be shut down and its static current recovered, which matters in a module that spends most of its life listening. The outputs go high impedance, so whatever pulls the far-end line has to be able to define a level on its own during that state.

Where this order code fits

Motion controllers, isolated digital output modules and battery management front ends use this part when four signals cross the barrier in one direction and the working voltage is a 1000 V class bus. Teams comparing it with a neighbouring part start from our Pin to Pin Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

What is the difference between ISO6740DWR and ISO6740FDWR? The default output state. The plain string holds the outputs high when the input side loses power or signal, the F string holds them low. The rest of the specification is identical.

Can the two sides run at different voltages? Yes. Each side accepts either 1.71 V to 1.89 V or 2.25 V to 5.5 V independently, and the part performs level translation between them in either direction of supply size.

Does 5000 VRMS mean a 5000 V working voltage? No. 5000 VRMS is a one-minute type test. The repetitive working voltage printed in the same table is 1500 VRMS, and that is the number a continuous 690 V or 1000 V bus has to be compared against.

Is a separate isolated supply needed? Yes. The part isolates signals only. Each side needs its own supply and its own ground, and the isolated side needs a winding, a module or an isolated regulator to feed it.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.