ISO5852SDWR
Product Specifications
ISO5852SDWR
Texas Instruments — Power Management & Signal Chain
Product Overview
The ISO5852SDWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ISO5852SDWR: A 2.5 A Source and 5 A Sink Gate Driver With Desaturation Protection
ISO5852SDWR is a reinforced isolated IGBT and MOSFET gate driver in a SOIC body of 16 pins. It splits the output into a 2.5 A source path and a 5 A sink path, adds a 2 A active Miller clamp, and turns the IGBT off softly over 2 microseconds when the desaturation comparator trips.
Order code and package
| Ordering string | ISO5852SDWR |
| Package | SOIC, 16 pins, DW body, 10.30 mm by 7.50 mm |
| Carrier | Tape and reel, 330 mm reel, 16 mm tape, pin 1 quadrant Q1 |
| Input supply | 2.25 V to 5.5 V |
| Output supply | 15 V to 30 V across VCC2 to VEE2 |
| Temperature range | minus 40 to plus 125 degrees Celsius ambient |
| Outputs | OUTH source, OUTL sink, plus CLAMP for the Miller clamp |
| Qualified version | ISO5852S-EP is the enhanced product string |
Electrical parameters that decide the application
| Peak output current | 2.5 A source and 5 A sink |
| Active Miller clamp | 2 A pull-down at CLAMP |
| Propagation delay | 76 ns typical, 110 ns maximum at 1 nF load |
| Output rise and fall at 1 nF | 12 ns typical, 18 ns typical, 35 ns maximum |
| Common-mode transient immunity | 100 kV per microsecond minimum at 1500 V common mode |
| Isolation rating | 5.7 kVRMS reinforced |
| Surge withstand | 12800 VPK |
| Input-side undervoltage lockout | Rising 2.25 V, falling 1.7 V, 0.2 V hysteresis |
| Output-side undervoltage lockout | Rising 12 V typical, falling 9.5 V minimum to 11 V typical, 1 V hysteresis |
| Desaturation threshold | 8.3 V minimum, 9 V typical, 9.5 V maximum with respect to GND2 |
| Blanking capacitor charge current | 0.42 mA minimum, 0.5 mA typical, 0.58 mA maximum |
| Leading-edge blanking | 20 ns minimum, 30 ns typical, 40 ns maximum |
| Soft turn-off | OUTH disabled and OUTL pulled low over 2 microseconds, then hard to VEE2 below 2 V |
| Input thresholds | 0.7 times VCC1 high, 0.3 times VCC1 low, plus or minus 20 ns glitch filter |
| Quiescent current | 2.8 mA to 4.5 mA on the input side, 3.6 mA to 6 mA on the output side |
Protection behaviour and pin functions
| Protection set | Desaturation detection with soft turn-off, output short-circuit clamp, active Miller clamp, undervoltage lockout on both sides |
| Status pins | FLT open-drain fault output, RST input to clear, RDY output for supply readiness |
| Split output | Separate OUTH and OUTL pins allow independent gate resistors for turn-on and turn-off |
| Clamp behaviour | CLAMP pulls the gate to 1.1 V maximum below the supply rail through a 2 A path to stop Miller-induced turn-on |
| Input logic | Two complementary CMOS inputs, IN+ and IN-, with internal pull-up and pull-down so a floating input means off |
| Family position | The 5.7 kVRMS 5 A class driver of its generation, the ISO5452 is the 2.5 A single-output sibling |
Points to check before this part goes on a BOM
The 9 V desaturation threshold is a fixed comparator, not a programmable one.DESAT is read against GND2 and trips between 8.3 V and 9.5 V. With a 600 V IGBT the diode chain from the collector sets how much of the collector-emitter voltage arrives at the pin, and the number of diodes has to be chosen so that a normal on-state drop stays below 8.3 V with margin. Too few diodes and the driver trips on every pulse.
Blanking time is set by the capacitor, and the current that charges it is 0.5 mA.The leading-edge blanking of 20 to 40 ns is internal, but the external blanking capacitor sets how long the comparator is ignored after turn-on. With 0.5 mA of charge current, a 100 pF capacitor reaches 9 V in about 1.8 microseconds, which is the order of the switching delay of a large IGBT.
Soft turn-off is what keeps the module alive.On a desaturation event the driver cannot simply slam the gate low, because the resulting di/dt through the stray inductance would put hundreds of volts across the IGBT. The part disables OUTH and pulls OUTL down over 2 microseconds, then finishes hard once the gate is below 2 V relative to VEE2.
The 2 A Miller clamp is a separate pin, not the sink path.During turn-off the gate is held at VEE2 by OUTL, and the CLAMP pin then pulls the gate to within 1.1 V of the negative rail with a 2 A path so that dv/dt coupling through the Miller capacitance cannot raise the gate. The clamp only works if the gate resistor allows it, so the CLAMP trace is run separately to the gate, not through the turn-off resistor.
Undervoltage lockout on the output side sits at 12 V rising and about 10 V falling.A 15 V nominal rail that sags to 11 V during a fault will leave the driver in lockout and the IGBT off, which is the safe result but also means a marginal supply looks like a driver fault. The RDY pin reports the state so the controller can tell the two apart.
Input-side logic is fail-safe by construction.IN+ is internally pulled low and IN- is pulled high, so a floating input means off, and pulses shorter than 20 ns are filtered out. A controller that goes quiet leaves the IGBT off rather than in its last state, which is the behaviour a bridge leg needs.
Sizing the blanking capacitor and the desaturation diodes
The blanking capacitor is charged from the 0.5 mA source while the IGBT is off, and it is clamped by the desaturation diodes while the IGBT is on. When the IGBT turns off, the capacitor has to charge back above 9 V before the next on pulse, and if the off time is shorter than the charge time the comparator will trip on the following pulse.
The practical rule is to size the capacitor from the desired blanking time at 0.5 mA and then check the recovery against the minimum off time of the modulator. A capacitor chosen for a long blanking time limits the maximum duty cycle.
What the split output buys in a high-current module
Separate OUTH and OUTL pins let the turn-on path carry a 2.5 A pulse through one resistor and the turn-off path a 5 A pulse through another. The asymmetry is what a large IGBT wants: a slower turn-on limits the recovery current of the freewheel diode, a fast turn-off limits switching loss.
Because the two paths are separate pins, the gate loop can be laid out so that the turn-off path has the shorter return, which matters more than the turn-on path for Miller-induced turn-on in a bridge leg.
Where this order code fits
Motor drives, solar inverters and welding supplies use this part where an IGBT or a large MOSFET needs desaturation protection, a Miller clamp and a 5 A turn-off path in one isolated package. Teams comparing it with a neighbouring part start from our Pin to Pin Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.
Questions buyers ask
What output supply range does ISO5852SDWR need? 15 V to 30 V across VCC2 to VEE2, which covers a unipolar 15 V gate drive and a bipolar plus 15 V minus 8 V arrangement with the same part.
Does it protect the IGBT against short circuit? It detects desaturation above about 9 V, mutes the output, then turns the gate off over 2 microseconds and reports the event on FLT. The protection is only as good as the desaturation diode network and the blanking capacitor around it.
Can the input run from 3.3 V? Yes. The input side accepts 2.25 V to 5.5 V and the thresholds scale with VCC1 at 0.7 and 0.3 times the rail, so a 3.3 V controller drives it directly.
Why is the part called 2.5 A and 5 A? 2.5 A is the peak source current that charges the gate, 5 A is the peak sink current on turn-off. The sink path is deliberately stronger.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.