Contact Us

ISO5452QDWRQ1

Brand: Texas Instruments
Texas Instruments ISO5452QDWRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ISO5452QDWRQ1 — Power Management & Signal Chain | Superb Automation

ISO5452QDWRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The ISO5452QDWRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

ISO5452QDWRQ1: automotive isolated IGBT and MOSFET gate driver with desaturation protection

ISO5452QDWRQ1 is a reinforced isolated gate driver for IGBTs and MOSFETs in a SOIC body of 16 pins. It drives an IGBT or a power MOSFET across a 5.7 kV RMS reinforced barrier with 2.5 A of source current, 5 A of sink current and split outputs, and it protects the switch with desaturation detection, soft turn off and an active Miller clamp. The QDWRQ1 order code is the wide body 16-pin SOIC, automotive grade, on a reel.

Order code and package

Order codeISO5452QDWRQ1
Package16-pin wide body SOIC, DW
Packingtape and reel
QualificationAEC-Q100 grade 1, minus 40 to plus 125 degrees ambient
Isolation5.7 kV RMS reinforced
Outputssplit OUTH and OUTL, 2.5 A source and 5 A sink
SuppliesVCC1 2.25 V to 5.5 V, VCC2 15 V to 30 V, VEE2 down to minus 15 V
Protectiondesaturation detection, soft turn off, Miller clamp, UVLO on both sides

Electrical parameters that decide the application

Common mode transient immunity50 kV per microsecond minimum, 100 kV typical at 1500 V
Miller clamp2 A active clamp on the gate during turn off
Fault reportingFLT on desaturation, RST to clear, RDY for supply status
Output short circuitclamped by an internal limiting circuit
Input thresholdCMOS with the input side running from 2.25 V
Isolation standardVDE 0884-17 reinforced, UL 1577, CQC

Family variants and how they differ

ISO5452-Q12.5 A source, 5 A sink, Miller clamp, automotive, this order code
ISO5451-Q1same drive strength without the Miller clamp
ISO5852S-Q1higher common mode immunity for fast switching devices
ISO5452QDWRQ1tape and reel, 16-pin wide body

Points to check before this part goes on a BOM

The split outputs exist so the turn on and turn off paths can use different resistors. Source current is 2.5 A and sink current is 5 A, and a single gate resistor sized for the 5 A sink path would slow the turn on far more than an IGBT needs, so the two resistors are separate line items on the bill of materials.

Desaturation detection is the protection that makes this part more than a level shifter. A DESAT pin with its diode and blanking capacitor watches the collector voltage, and when the switch stops saturating the driver mutes the output and performs a soft turn off instead of a hard one, which is what keeps a short circuit from turning into an explosion.

The 2 A active Miller clamp holds the gate low through a dedicated path once the output has fallen. On a bridge leg with a fast dv/dt, the current through the gate collector capacitance can pull a turned off switch back on, and the clamp is the answer to that rather than a negative gate supply.

Output side supply range starts at 15 V and reaches 30 V, with VEE2 allowed down to minus 15 V. A 15 V unipolar drive is the minimum for most 1200 V IGBTs, and a bipolar plus 15 V and minus 8 V arrangement needs both rails from the isolated supply, which doubles the transformer secondary and the rectifier count.

The 50 kV per microsecond minimum common mode transient immunity at 1500 V is the number that decides whether the driver survives an inverter leg switching at 20 kV per microsecond with a long emitter connection. The typical figure is 100 kV per microsecond, and a board with a big parasitic capacitance across the barrier turns the minimum into the working number.

UVLO on both sides with the RDY pin means the controller can hold the bridge off until both supplies are valid. Starting a bridge with the output side still below its UVLO threshold produces a partially enhanced switch, which is the failure mode the RDY signal exists to prevent.

Automotive grade 1 is an ambient rating of minus 40 to plus 125 degrees, and it is not the same as a junction rating. An inverter module that runs its driver at 110 degrees ambient leaves only 15 degrees for self heating, and the driver dissipation from 5 A gate pulses at 20 kHz is the number to check against that margin.

The desaturation blanking capacitor sets how long the driver waits before it believes the switch has failed to saturate. Too short and every turn on trips a fault through the normal rise of collector voltage, too long and the switch carries a short circuit current for longer than it can. The value follows the blanking current in the data sheet and the bus voltage, not a generic number.

Total gate charge decides the drive loss. At 20 kHz with 1 microcoulomb of gate charge, the 2.5 A source path spends about 20 mW in the driver and the isolated supply has to deliver the average current of 20 mA. Doubling the switching frequency doubles both, and a driver chosen for a 10 kHz bridge is often short of supply current at 40 kHz.

Where this order code fits

It is used in hybrid and electric vehicle inverter modules, motor drives, solar inverters, induction heating and industrial power supplies that switch an IGBT or a silicon carbide device across an isolation barrier. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Does it include the isolated supply? No. The barrier carries the gate signal, and the output side needs its own 15 V to 30 V supply with an optional negative rail, usually from a small transformer driver.

What does the FLT pin report? A desaturation event. The output is muted and the switch is turned off softly, and RST clears the latch once the controller has decided what to do next.

Can it drive a silicon carbide MOSFET? The 5 A sink and 2.5 A source are enough for most modules, but the desaturation threshold and blanking time have to be set for the higher saturation voltage and faster switching of a wide bandgap device.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.