Contact Us

ISO3086TDWR

Brand: Texas Instruments
Texas Instruments ISO3086TDWR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ISO3086TDWR — Power Management & Signal Chain | Superb Automation

ISO3086TDWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The ISO3086TDWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

ISO3086TDWR: A Full-Duplex 20 Mbps Isolated RS-485 Transceiver in the ISO308x Family

ISO3086TDWR is an isolated full-duplex RS-485 and RS-422 transceiver in a SOIC (DW) body of 16 pins. It is the full-duplex member of the ISO308x family at 20 Mbps, with a separate driver and receiver pair so a four wire bus can be driven and read at the same time.

Order code and package

Ordering stringISO3086TDWR
PackageSOIC, 16 pins, DW body, 10.30 mm by 7.50 mm nominal
CarrierThe industrial rows print a 330 mm reel with 16.4 mm tape and a 2000 piece quantity
Temperature rangeMinus 40 to plus 85 degrees Celsius on every row of this family
DuplexFull duplex, separate driver pair and receiver pair
Logic side supply3.3 V inputs that are 5 V tolerant
Bus side supply5 V nominal
Tube siblingISO3086DW, same die in a tube
Addendum noteThe rows print ISO3086DW, DWR, DWR.A and DWRG4 and none of them carries the T letter

Electrical parameters that decide the application

Signaling rateUp to 20 Mbps
Isolation rating2500 VRMS for 60 seconds per UL 1577
Basic insulation4000 VPK per DIN EN IEC 60747-17 and CSA 62368-1
Working voltage560 VPK repetitive peak
Bus loadingOne eighth unit load, up to 256 nodes
Bus capacitance16 pF typical
Common mode transient immunity50 kV per microsecond typical
ESD, bus pins to bus ground12 kV human body model
ESD, bus pins to logic ground6 kV human body model
Fail-safeReceiver output high on bus open, short and idle
Thermal protectionShutdown on overtemperature
Logic threshold3.3 V inputs accepted with a 5 V rail present
BarrierSymmetrical, tested for 60 seconds
Body size10.30 mm by 7.50 mm, the narrow wide body of this family

Family variants and how they differ

ISO3080Full duplex, same 20 Mbps class, different pin arrangement
ISO3082Half duplex, the two wire equivalent
ISO3088Half duplex with the fastest delay class of the family
ISO1412BFull duplex 500 kbps isolated transceiver when the bus is slow
ISO1432BFull duplex 12 Mbps
ISO1452BFull duplex 50 Mbps for a faster four wire bus

Points to check before this part goes on a BOM

No row of this addendum carries the T letter. The printed strings are ISO3086DW, ISO3086DWR, ISO3086DWR.A and ISO3086DWRG4, so the suffix on this catalogue entry should be confirmed against a customer order before a reel is bought in.

The DWR row prints its quantity as call TI while the G4 row of the same reel prints 2000, and the DWR.A row is printed obsolete. A purchase order that names the plain DWR string can therefore be answered with a different packing than expected.

The family stops at 85 degrees ambient. A cabinet that runs hot needs the wider temperature isolators rather than this part with a heatsink.

Full duplex needs four wires. A two wire retrofit uses ISO3082 or ISO3088, and the two parts are not interchangeable on the same footprint even though the body size matches.

The bus capacitance of 16 pF typical is a property of the pins and it adds to the cable capacitance. A long run with 256 nodes is limited by the total, not by the per device figure.

The ESD ratings differ by which ground the pulse returns to: 12 kV from the bus pins to the bus ground and 6 kV to the logic ground. A test report that quotes one number without the other is incomplete.

The fail-safe receiver holds the output high when the bus is open, shorted or idle, so a controller that reads the line during a break sees a defined mark. Without that behaviour a floating pair reads as noise and the protocol layer sees a stream of frame errors.

The driver on the isolated side sources the full bus current and the receiver loads the same pair, so a four wire segment measures both directions at the same time. Sizing the isolated supply for one direction at a time will undersize it on a bus that is busy in both directions.

Why a full-duplex isolated transceiver is still ordered

Four wire buses are common in process control because they remove the turnaround delay of a half duplex line. The cost is one extra pair of wires and a transceiver with separate driver and receiver enables, which is what this part provides on the isolated side.

Wiring a four wire bus on the isolated side

A full duplex transceiver needs its own pair for the driver and its own pair for the receiver, and both pairs need a termination at the far end. On the isolated side the two pairs share the isolated ground, and that ground is the reference the common mode range has to be measured against.

Because the driver and the receiver are separate, a node can transmit while it receives its own traffic only if the bus is wired as a true four wire ring, which is what process networks do to remove the turnaround delay of a two wire line.

The 85 degree ceiling and the thermal shutdown

This family is qualified to 85 degrees ambient, and the thermal shutdown inside the device protects the driver rather than extending the rating. In a cabinet that runs at 70 degrees the margin left for self heating is small, and a fault that keeps the driver in a short circuit will reach the shutdown threshold quickly.

The practical answer is to look at the cabinet temperature rather than the board temperature, because the part is heated by the bus current it is sourcing and by everything else on the same copper. A drive that works on a bench at 25 degrees can fail in a closed cabinet at 60.

A 3.3 V controller on a 5 V bus

The inputs on this family are 3.3 V logic that tolerates 5 V, so a 3.3 V controller can drive the logic side while the bus side runs at 5 V. The supply pins are separate, and the part translates across the barrier rather than through a level shifter on the board.

The current consumption on the logic side is small, but the bus side has to source the driver current into a terminated pair, which is where most of the supply budget goes on a busy segment.

Buying an isolated transceiver on a lead time

The strings in this family do not all have the same status, and the difference between an active reel row and a row printed obsolete is the difference between a two week delivery and a broker search. Checking the current addendum before quoting is faster than checking it after the customer has approved a date.

Where this order code fits

It is used on four wire field buses where the controller has to transmit and receive at the same time and the field ground cannot be tied to the cabinet ground. Teams comparing it with a neighbouring part start from our Pin to Pin Cross Reference page, and teams replacing a part that has gone end of life start from the Obsolete RF Part Replacement page.

Questions buyers ask

Is this the same die as ISO3088? Same family and same barrier, different channel arrangement. ISO3086 is full duplex and ISO3088 is half duplex, so the pin map and the bus wiring differ.

What does the T in the ordering string mean? The addendum used for this page does not print a T row, so the letter is stated as unconfirmed rather than explained. The industrial strings and the G4 rows are the ones that can be verified today.

How many nodes fit on one bus? One eighth unit load per device and up to 256 nodes, which is the ceiling of the RS-485 standard rather than a property of this part alone.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Supplier Onboarding Checklist page sets out the checks that keep a substitute from failing on the bench.