Contact Us

INA4180A1IPWR

Brand: Texas Instruments
Texas Instruments INA4180A1IPWR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA4180A1IPWR — Power Management & Signal Chain | Superb Automation

INA4180A1IPWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA4180A1IPWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA4180A1IPWR: the gain of twenty member of the four channel unidirectional current sense family

INA4180A1IPWR is the gain of twenty member of the four channel current sense family, in the fourteen pin TSSOP on the large reel. The four channels share one supply pin pair and one bias block, so four shunts on one board are read through one package and one quiescent current line.

A gain of twenty turns a 10 milliohm shunt at 5 amps into 1 volt at the output, which is the highest gain of the four options and therefore the one with the lowest bandwidth at 350 kilohertz. The common mode window runs from 0.2 volts below ground to 26 volts independent of the 2.7 to 5.5 volt supply, so the same package reads a low side shunt on a 3.3 volt rail and a high side shunt on a 24 volt rail.

INA4180A1IPWR as the vendor document publishes it

Channels4
Gain options20, 50, 100 and 200 volts per volt, fixed by an internal network
Common mode range0.2 volts below ground to 26 volts
Supply2.7 to 5.5 volts
Offset at zero volts of common modeplus or minus 25 microvolts typical, plus or minus 150 maximum
Offset at 12 volts of common modeplus or minus 100 microvolts typical, plus or minus 500 maximum
Offset drift0.2 microvolts per degree typical, 1 maximum
Common mode rejection84 decibels minimum, 100 typical
Power supply rejection80 microvolts per volt
Gain error0.1 per cent typical, 1 per cent maximum
Gain error drift20 parts per million per degree
Nonlinearity0.01 per cent between 0.5 volts and half a volt below the supply
Bandwidth350, 210, 150 and 105 kilohertz for the four gains
Slew rate2 volts per microsecond
Voltage noise40 nanovolts per root hertz
Quiescent current900 microamps typical, 1 milliamp maximum for four channels
Temperature rangeminus 40 to plus 125 degrees
Package14 pins, TSSOP body PW
Catalogue codeINA4180A1IPWR
Vendor statusactive
Gain20 volts per volt
Carrierlarge reel, R suffix
Package14 pins, TSSOP body PW

Four current sense channels in one fourteen pin TSSOP

INA4180A1IPWR is one quarter of the INAx180 family, a voltage output current sense amplifier with a fixed gain, packaged four to a fourteen pin TSSOP. The four gain options are 20, 50, 100 and 200 volts per volt, and the gain is set by a matched resistor network inside the package rather than by an external pair, so the gain error and the drift come from one trimmed block.

The common mode window runs from 0.2 volts below ground to 26 volts, independent of the 2.7 to 5.5 volt supply, which is what allows the part to sit on the high side of a 24 volt rail and still drive a converter that runs at 3.3 volts. All four channels share the supply pins but not the inputs, so four separate shunts can be read through one package.

Offset at zero volts of common mode, and again at twelve

The offset of INA4180A1IPWR is quoted twice, because the answer depends on where the inputs sit. At a common mode of zero volts the row reads plus or minus 25 microvolts typical and plus or minus 150 microvolts maximum. At a common mode of 12 volts the same row reads plus or minus 100 microvolts typical and plus or minus 500 microvolts maximum.

The drift is 0.2 microvolts per degree typical and 1 microvolt per degree maximum across the minus 40 to plus 125 degree range. On a 10 milliohm shunt at 5 amps the sense voltage is 50 millivolts, so 500 microvolts is one per cent of reading, and that is the number to put against the tolerance of the shunt itself before choosing a gain.

Three hundred and fifty kilohertz at a gain of twenty, and the three lower numbers

The bandwidth of INA4180A1IPWR falls as the gain rises, because the gain is set by the same internal network. The A1 device at a gain of 20 holds 350 kilohertz, the A2 at 50 holds 210 kilohertz, the A3 at 100 holds 150 kilohertz and the A4 at 200 holds 105 kilohertz, all measured at a 10 millivolt sense voltage.

The slew rate is 2 volts per microsecond on all four, and the voltage noise density is 40 nanovolts per root hertz. A 20 kilohertz switching supply measured through a 200 volts per volt channel therefore has five times the headroom it needs, while a 100 kilohertz current loop on the same channel is already at the edge of the small signal response.

Gain error of one per cent, and what it costs at ten millivolts

The gain error of INA4180A1IPWR is 0.1 per cent typical and 1 per cent maximum, with 20 parts per million per degree of drift and a nonlinearity of 0.01 per cent between 0.5 volts and half a volt below the supply. The power supply rejection is 80 microvolts per volt, so a 100 millivolt supply step moves the output by 8 microvolts referred to the input.

A one per cent gain error on a 10 millivolt sense signal is 100 microvolts, which is small against the 500 microvolt offset at a 12 volt common mode but larger than the offset at zero common mode. That ordering is why the family is specified with both common mode cases rather than one, and why a two point calibration at the working common mode recovers most of the error.

Nine hundred microamps for four channels, and the carrier rows

The quiescent current of INA4180A1IPWR is 900 microamps typical and 1 milliamp maximum at 25 degrees, and it is quoted for the whole package rather than for one channel, because the four amplifiers share one bias block. Over the full temperature range the maximum rises to the same 1 milliamp figure, so the supply budget does not change with the ambient.

The package is the fourteen pin TSSOP, and the reel code carries the R suffix while the tube code carries a T. The body is the same one used by the dual and single members of the family, so the land pattern for four channels is the only one a board needs if the channel count may grow.

Where four current sense channels belong

INA4180A1IPWR belongs in a three phase motor drive, where three shunts read the phase currents and the fourth reads the bus return; in a quad hot swap card, where each rail has its own shunt; in a power over ethernet switch, where four ports are monitored through one package; and in a battery tester that cycles four cells at once.

The 26 volt common mode, the fixed gains and the 900 microamps are the three rows that fit those cases. What the part does not do is measure current in both directions, because the output is referred to ground rather than to a mid supply reference, and that is the difference between this family and the bidirectional one beside it.

What the four channels do not share

The four channels of this package share the supply pins, the bias block and the ground return, and they share nothing else. Each has its own input pair and its own output, so a fault on one shunt does not move the other three, and the four outputs can be read by four separate converter channels or by one multiplexed converter.

What they do share is the ground return current, and that is the coupling path a four channel part introduces where four single parts would not. The return from four outputs at 1 milliamp each is small, but the return from four shunts on the same copper is not, so the star point of the four shunt returns is the one place on the board that decides whether the channel to channel separation is real.

The gain choice follows from the shunt and the full scale current, not from the stock list. Our amplifier cross reference page covers the four gains, and the BOM scrubbing page covers the shunt against the bill of materials.

Why is the bandwidth lower at a gain of twenty? Because the gain network is inside the package and the same amplifier drives it, so the closed loop bandwidth falls as the gain rises: 350 kilohertz at 20, 210 at 50, 150 at 100 and 105 at 200.

Can four channels share one shunt? No. Each channel has its own input pair, and the four are independent, which is what allows four different shunts on four different rails through one package.