INA2321EA250
Product Specifications
INA2321EA250
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA2321EA250 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA2321EA250: the same micropower dual on a 250 piece reel
INA2321EA250 is the dual micropower CMOS instrumentation amplifier in the fourteen pin TSSOP on a 250 piece small reel, the vendor string INA2321EA/250. It is the same die and the same electrical rows as the 2500 piece reel, and the difference is the carrier: 250 pieces on a small reel rather than 2500 on a 330 millimetre one.
Two hundred and fifty pieces covers a pilot run and a first article without committing to a production reel, and the part is moisture level 1 with an unlimited floor life on both carriers. The rows that decide the application are the 40 microamps per channel, the 10 picoamps of bias current, the 500 kilohertz at a gain of 5 and the shutdown current of 0.01 microamps.
INA2321EA250 as the vendor document publishes it
| Channels | 2 |
| Gain | 5 to 1000 V/V, 5 + 5 (R2/R1) |
| Supply | 2.7 to 5.5 volts specified, 2.5 to 5.5 operating |
| Quiescent current | 40 microamps typical, 60 maximum per channel |
| Shutdown current | 0.01 microamps typical, 1 maximum per channel |
| Offset at 5 volts | 0.2 millivolts typical, 0.5 maximum, 1 millivolt over temperature |
| Offset over the full range | 2.2 millivolts typical, 2.5 maximum |
| Offset drift | 7 microvolts per degree |
| Rejection | 90 minimum, 94 typical decibels, 80 minimum over temperature |
| Input bias current | 0.5 picoamps typical, 10 maximum |
| Voltage noise | 500 nanovolts per root hertz at 10 hertz |
| Gain error | 0.02 typical, 0.1 maximum per cent |
| Gain drift | 2 parts per million per degree typical, 10 maximum |
| Bandwidth and slew | 500 kilohertz at a gain of 5, 0.4 volts per microsecond at a gain of 25 |
| Settling time | 8 microseconds to 0.1 per cent at a gain of 5 |
| Temperature range | minus 55 to plus 125 degrees |
| Vendor status | active, 250 piece small reel |
| Catalogue code | INA2321EA250 |
| Vendor string | INA2321EA/250 |
| Carrier | small reel of 250 |
| Moisture level | level 1, unlimited floor life |
Five plus five times a ratio, and forty microamps per channel
INA2321EA250 is a dual CMOS instrumentation amplifier in a 14 pin TSSOP that draws 40 microamps typical and 60 maximum per channel from a 2.7 to 5.5 volt supply, and 0.01 microamps when the shutdown pin is pulled low. The gain is 5 plus 5 times the ratio of two external resistors, so the internal five is trimmed and anything above it is set on the board up to 1000.
Forty microamps is the number that matters. A two channel front end costs 80 microamps, which is less than the quiescent current of most 16 bit converters, so a battery instrument can keep the amplifier awake between readings instead of powering it per sample. The shutdown pin brings that to 0.01 microamps, which is below the leakage of a dirty board, so the sleep current is set by the rest of the circuit.
Ninety four decibels, and the window it is measured over
The common mode rejection of INA2321EA250 is 90 dB minimum and 94 dB typical at a 5 volt supply over an input window of 0.55 to 3.8 volts, with 80 dB minimum over temperature. At a 2.7 volt supply the window narrows to 0.35 to 1.5 volts and the rejection holds at 94 dB typical, which is the row to read for a 3 volt system.
The window is the limitation rather than the rejection. A rail to rail input is not what this part offers: at 5 volts it stops 1.2 volts below the positive rail and 0.55 volts above ground. A high side sense on a 12 volt bus, or a sensor that sits at the positive rail, needs a different part. A bridge biased at mid rail, an RTD with a 1 milliamp excitation, or an electrode at 2.5 volts sits inside the window and sees the full 94 dB.
Half a millivolt typical, one millivolt maximum
The offset of INA2321EA250 is 0.2 millivolts typical and 0.5 maximum at a 5 volt supply, with 1 millivolt as the over temperature limit at 25 degrees and 2.2 to 2.5 millivolts over the full minus 55 to plus 125 degree range. The drift is 7 microvolts per degree, and the power supply rejection is 50 microvolts per volt typical against 200 maximum.
Those figures are two orders of magnitude looser than a chopper part and one order tighter than a general purpose CMOS amplifier, which is the slot this family occupies. On a 100 millivolt full scale sensor, 1 millivolt is 1 per cent and the over temperature 2.5 millivolts is 2.5 per cent, so a channel that needs 0.1 per cent has to calibrate. A channel that needs 5 per cent can use the part with no calibration at all.
Five hundred kilohertz at a gain of five, eight microseconds to settle
The bandwidth of INA2321EA250 is 500 kilohertz at a gain of 5, with a slew rate of 0.4 volts per microsecond at a gain of 25 and a settling time of 8 microseconds to 0.1 per cent at a gain of 5 on a 2 volt step. The output swings to within 20 millivolts of each rail, and the nonlinearity is 0.001 per cent of full scale at a gain of 25.
That combination is what a multiplexed battery instrument needs: eight channels scanned through one amplifier at 8 microseconds each is 64 microseconds of settling for the bank, and a 16 bit converter running at 100 samples per second spends most of its period converting rather than waiting. The 500 kilohertz also sets the noise band, so a 100 kilohertz bandwidth at a gain of 5 sees 160 microvolts of the 500 nanovolt noise, which is a sixth of the offset.
Ten picoamps of bias current, and what that buys
The input bias current of INA2321EA250 is 0.5 picoamps typical and 10 picoamps maximum, with an offset current of the same order, and the input impedance is 10 to the 13 ohms in parallel with 3 picofarads. On a 1 megaohm source 10 picoamps is 10 microvolts, which is smaller than the offset, and on a 100 megaohm source it is 1 millivolt, which is the same as the offset.
That is what makes the part usable on a pH electrode, a photodiode in photovoltaic mode, or a piezoelectric sensor with a 10 megaohm bias resistor. A bipolar input with 5 nanoamps of bias current would produce 50 millivolts on the same source and would need a different front end. The trade is noise: the current noise of 3 femtoamps per root hertz is low, but the voltage noise of 500 nanovolts per root hertz at 10 hertz is high, so a low impedance source is better served by a bipolar part.
Where a micropower CMOS front end belongs
INA2321EA250 belongs in a battery powered bridge, a pH or conductivity probe, a photodiode preamplifier, a portable ECG and a field meter that has to run for a season on one cell. The 40 microamps per channel, the 10 picoamps of bias current and the 500 kilohertz are the three rows that decide those cases, and the shutdown pin makes it usable in a logger that wakes once a minute.
It does not belong where the offset has to be under 100 microvolts, which is a chopper part. It does not belong where the input has to reach the positive rail. It does not belong on a source above 10 megaohms, where the current noise and the leakage of the board dominate. And it does not belong in a wideband signal path, because 500 kilohertz is the ceiling at a gain of 5. Our amplifier cross reference page covers the chopper and the bipolar alternatives, and the vendor consolidation page covers holding the single and the dual on one line.
A small reel is bought on availability for a first build. Our BOM scrubbing page covers the gain pair, and the vendor consolidation page covers the move to the large reel at production.
Is the small reel the same part? Yes, one die, one set of rows, one level 1 floor life; only the quantity changes.
What does the shutdown pin do to the pair? It takes both channels to 0.01 microamps typical and 1 microamp maximum per channel.