INA228AQDGSRQ1
Product Specifications
INA228AQDGSRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA228AQDGSRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA228AQDGSRQ1: 85 V, 20 bit power and energy monitor with an I2C interface
INA228AQDGSRQ1 is a digital power monitor that reports current, bus voltage, power, energy and charge in a VSSOP body of 10 pins. It converts a shunt drop and a bus voltage with one 20 bit delta sigma converter and delivers the results over I2C already multiplied into watts, joules and coulombs. The common mode window runs from minus 0.3 V to 85 V, the shunt full scale is selectable at 163.84 mV or 40.96 mV, and the die carries its own temperature sensor for ambient logging next to the shunt.
Order code and package
| INA228AIDGSR | VSSOP DGS body, 10 pins, 2500 pieces on a large reel, Active in the addendum, part marking 228I, moisture level 2 with a one year floor life |
| INA228AIDGSR.A | the same body and the same 2500 piece reel, printed as a second row of the same addendum |
| Catalogue string on this page | INA228AQDGSRQ1 carries the automotive qualifier; the addendum of SLYS021A prints INA228AIDGSR only, so reel size, grade and marking for the Q1 string were left unconfirmed here |
| Body size | the DGS body is the ten pin VSSOP, junction to case top 10 degrees per watt and junction to board 177.6 degrees per watt |
Electrical parameters that decide the application
| Common mode input range | minus 0.3 V to 85 V, independent of the supply |
| Bus voltage input | 0 V to 85 V on the VBUS pin |
| Shunt full scale | plus or minus 163.84 mV with ADCRANGE at 0, plus or minus 40.96 mV with ADCRANGE at 1 |
| Shunt offset voltage | plus or minus 1 uV maximum, drift plus or minus 0.01 uV per degree |
| Gain error | plus or minus 0.05 per cent maximum, drift plus or minus 20 ppm per degree |
| Common mode rejection | 154 dB minimum from minus 0.3 V to 85 V over the full temperature range |
| Power accuracy | 0.5 per cent of full scale maximum from minus 40 to plus 125 degrees |
| Energy and charge accuracy | 1.0 per cent of full scale maximum |
| Input bias current | 2.5 nA maximum, which is what allows a shunt in the milliohm range |
| Supply and current | 2.7 V to 5.5 V, 640 uA typical while converting, 5 uA maximum in shutdown |
| Conversion time and averaging | 50 us to 4.12 ms per input, set independently for shunt, bus and temperature, with 1 to 1024 samples averaged |
| Interface | I2C at 2.94 MHz, 16 pin selectable addresses through A0 and A1, alert output asserted within 75 us |
Family variants and how they differ
| ADCRANGE at 0 | the wide window at plus or minus 163.84 mV, one least significant bit is 312.5 nV on a 20 bit result |
| ADCRANGE at 1 | the narrow window at plus or minus 40.96 mV, four times the resolution on the same shunt |
| 16 addresses | A0 and A1 may each be tied to GND, SCL, SDA or VS, which is what makes a multi rail board possible without a bus switch |
| Temperature path | the internal sensor reads the die, plus or minus 1 degree at 25 degrees, and a programmable resistor temperature compensation coefficient corrects the shunt rather than the amplifier |
| Automotive string | the Q1 order code is a separate qualified device; the document attached to this page does not print its addendum row |
Points to check before this part goes on a BOM
The 20 bit converter is the reason the part can serve a shunt in the milliohm range without a second gain stage. At the narrow window one step is a fraction of a microvolt, and the 2.5 nA input bias current means a 0.5 milliohm shunt does not lose its reading to the amplifier input.
Energy and charge are accumulated inside the device. A host that polls current at its own pace still gets a true joule count, because the integration runs on the internal oscillator quoted at plus or minus 0.5 per cent instead of on a host timer that stops when the firmware is busy.
The three conversion times are set separately. A board that needs a fast overcurrent alert but a slow, quiet bus voltage reading can run the shunt channel at 50 us and the bus channel at 4.12 ms, so a rail that is noisy during a converter burst is not forced to trade the trip time for the resolution, and the total cycle time is the sum of the enabled channels rather than the slowest one.
Averaging runs from one sample to 1024 samples and applies to every enabled input at once. It is the cheapest way to buy resolution on a noisy rail, but the update rate falls with it, so an alert threshold that has to trip in a few hundred microseconds belongs on the fast path with no averaging.
The automotive string on this page is not printed in the addendum of this document. The addendum lists INA228AIDGSR and INA228AIDGSR.A at 2500 pieces on a large reel, both marking 228I, and the Q1 device carries its own qualification file. Reel size, marking and temperature grade for INA228AQDGSRQ1 therefore have to be confirmed against the automotive document or a vendor reply before a purchase order is raised.
Choosing between the two shunt windows
The wide window suits a rail where the current swings over a decade and the board only needs a healthy margin on the shunt. The narrow window gives four times the resolution on the same resistor, but a 40.96 mV ceiling means a 1 milliohm shunt saturates at just over 40 A, so the shunt value and the window have to be chosen together rather than one after the other.
Both windows keep the same 154 dB of common mode rejection, so moving to the narrow range does not trade rejection for resolution. What changes is the headroom against a current spike, and that is the number to check against the inrush of the load rather than the steady state rating of the supply.
Where the alert pin earns its place
The alert output responds within 75 us and works from a threshold register rather than from a host comparison, so a firmware loop that is late by a few milliseconds does not delay the trip. On a battery pack or a power over ethernet port the pin usually drives a hot swap controller directly, and the ADC result is read afterwards to find out what happened.
Where this order code fits
DC to DC converters and power inverters, industrial battery packs, power over ethernet ports, telecom equipment and enterprise servers are the applications the vendor names, and all of them want a rail that reports its own consumption rather than a shunt amplifier feeding a host ADC. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
Can it measure a negative current? Yes. The shunt input is differential and bipolar, so a pack that charges and discharges through the same resistor reports both directions without a second device.
How many devices fit on one bus? Sixteen, because A0 and A1 can each be tied to GND, SCL, SDA or VS, and the device samples both pins on every bus transaction.
Does the bus voltage input need a divider? It accepts 0 V to 85 V directly, so a divider is only needed above that window.
Is the temperature reading the board or the die? It is the die temperature, plus or minus 1 degree at 25 degrees, which is why the vendor also provides a resistor temperature compensation coefficient for the shunt itself.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.