Contact Us

INA226AIDGSR

Brand: Texas Instruments
Texas Instruments INA226AIDGSR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA226AIDGSR — Power Management & Signal Chain | Superb Automation

INA226AIDGSR

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA226AIDGSR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA226AIDGSR: 36 V 16 bit current, voltage and power monitor with an alert output

INA226AIDGSR is an I2C current, voltage and power monitor with a 16 bit converter in a VSSOP body of 10 pins. It measures shunt drop and bus voltage on a rail up to 36 V with a 16 bit converter and reports current, voltage and power in engineering units after the host writes one calibration value. The DGSR order code is the 10-pin VSSOP with the alert pin on a reel.

Order code and package

Order codeINA226AIDGSR
Package10-pin VSSOP, 3.0 mm by 4.9 mm including pins
Packingtape and reel
Bus range0 V to 36 V, high side or low side
InterfaceI2C and SMBus, 16 programmable addresses
Resolution16 bit ADC on shunt and bus
Supply2.7 V to 5.5 V, 330 microampere typical
Extra pinALERT output for over limit and conversion ready

Electrical parameters that decide the application

Shunt full scale81.92 mV, set by the calibration register and the shunt value
Shunt offset2.5 microvolt typical, 10 microvolt maximum
Shunt gain error0.02 percent typical, 0.1 percent maximum
Bus full scale40.96 V at the converter, 36 V maximum at the pin
Bus offset1.25 millivolt per count
Conversion time588 to 646 microseconds in the 1.1 ms setting
Averagingup to 1024 samples per update

Family variants and how they differ

INA22616 bit, 36 V, alert pin, this order code
INA22012 bit, 26 V, no alert pin
INA21912 bit, 26 V, earlier register map
INA226AIDGSR2500 pieces per reel in the ten pin VSSOP

Points to check before this part goes on a BOM

The converter has a 16 bit shunt channel with 2.5 microvolt of typical offset, so on a 10 milliohm shunt one count is about 2.5 microampere and the offset is roughly one count. The same part on a 1 milliohm shunt has a 25 mA count and 2.5 mA of offset, which is why a high current rail is measured with a small shunt and a large full scale rather than the other way round.

The bus voltage channel has a 1.25 mV least significant bit and a 40.96 V converter range against a 36 V pin limit. The converter range exists so that a 36 V rail at the top of tolerance still fits, and the data sheet is explicit that 36 V is the maximum that may be applied even though the scaling goes higher.

Power is calculated inside the device from the current register and the bus register, and the calibration value the host writes is what ties current in amperes to the shunt in ohms. A wrong calibration value produces a current reading that looks plausible and a power reading that is wrong by the same factor, with no error flag anywhere.

Averaging is the setting that trades update rate for noise, and the 1024 sample setting gives an update every second or so. A protection loop that needs a response inside 10 ms cannot use that setting, and the alert output reacts to the averaged value rather than to a single conversion.

The alert pin can be configured as a latched or transparent over limit output, and a latched alert has to be cleared by reading the mask register. Firmware that polls the current register and ignores the pin still works, but the pin is the only path that reports a transient shorter than one averaged update.

Common mode is independent of the 2.7 V to 5.5 V supply, so the part sits on a 3.3 V logic rail while measuring a 24 V or 36 V bus. The shunt inputs still have to stay inside their own range: a high side shunt on a 36 V rail sits at 36 V, and a low side shunt sits at ground, and both are inside the specified input range.

Sixteen addresses are decoded from two pins, and the address pins are read at conversion time rather than latched at power up. A board that drives those pins from a microcomputer has to hold them stable, because a change mid conversion moves the device to a different address.

Shunt self heating is a quiet error source at high current. A 1 milliohm shunt at 20 A dissipates 0.4 W, and the resulting temperature rise changes the shunt resistance by tens of ppm, which appears as a gain error that grows with load. A four terminal shunt removes the solder joint resistance from the measurement but not this drift.

The bus voltage channel and the shunt channel are converted in sequence, so the two readings in one update are not simultaneous. On a load that changes within a conversion cycle the power product mixes two different instants, and averaging widens that window rather than narrowing it.

Where this order code fits

It is used in rack servers, wireless infrastructure, high performance computing, battery monitors and balancers, power supplies and bench instruments that need calibrated current and power telemetry. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the MCU Cross Reference page.

Questions buyers ask

What shunt value should I start with? One that gives about 80 mV at the highest current to be measured, which is the shunt full scale, and then check that the offset stays small against the lowest current that matters.

Can it replace an INA220? The package and interface match but the bus range, resolution and register map differ, so firmware and calibration both change. It is a functional upgrade rather than a drop in.

What does the alert pin do? It asserts on an over limit condition or when a conversion is ready, and it can be latched so a short event is not missed between polls.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.