INA2181A3IDSQR
Product Specifications
INA2181A3IDSQR
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA2181A3IDSQR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA2181A3IDSQR: two bidirectional 100 V/V channels in a WSON-10
The INA2181A3IDSQR is the dual bidirectional member of the INA181 family at 100 V/V, in a 10 pin WSON body. Where the INA2180 reads current in one direction, the INA2181 puts a reference pin on each channel so the output can sit mid range at zero current and swing either side of it. Common mode runs from 0.2 V below ground to 26 V above, the supply is 2.7 V to 5.5 V, offset is 150 uV maximum at 0 V and 500 uV at 12 V, drift is 1 uV per degree, gain error is 1 percent and bandwidth at gain 100 is 150 kHz with a 10 pF load. Both channels draw 500 uA maximum.
Bidirectional sensing matters wherever a battery is involved. A pack that charges and discharges through the same shunt reverses the drop, and a unidirectional monitor reads the discharge as zero and hides half the energy flow. The INA2181 solves that with two extra pins, not with a second shunt, which keeps the sense path and the calibration single. The A3 gain of 100 lands a 10 mV full scale sense at 1 V of output around the reference level.
Key data for the INA2181A3IDSQR
| Gain | 100 V/V per channel, four options from 20 to 200 in the same dual family |
| Input | Common mode minus 0.2 V to plus 26 V per channel, bidirectional through a per channel reference pin |
| Accuracy | Offset 150 uV maximum at 0 V and 500 uV at 12 V, 1 uV per degree drift, 1 percent gain error |
| Bandwidth | 150 kHz at gain 100 with a 10 pF load, 355 kHz at gain 20 and 105 kHz at gain 200 |
| Supply | 2.7 V to 5.5 V, 500 uA maximum for both channels, one 0.1 uF bypass |
| Output | Each channel swings around its own reference, so a mid rail reference gives plus and minus current |
Body, marking and reel data
| Body | DSQ, WSON 10 pin, a wider body than the 8 pin WSON of the unidirectional family |
| Reel | 3000 pieces on a large reel on the active lettered row, NIPDAU finish at moisture level 1 |
| Marking | Four characters per gain in the addendum, read alongside the reel label rather than alone |
| Packing | The plain row prints a different packing column from the lettered row of the same string |
| Temperature | Minus 40 C to 125 C, industrial rows, no automotive row in this document |
Charging and discharging through one shunt
The reference pin sets the zero current output level, so the converter that reads it needs headroom on both sides. On a 3.3 V supply a 1.65 V reference leaves 1.65 V of swing each way, which at gain 100 is 16.5 mV of shunt drop in either direction. A 2 milliohm shunt then covers plus and minus 8 A, which is a realistic pack current for a light electric vehicle or a large power tool. Choosing the reference at a quarter rail buys more range in one direction and less in the other, and that asymmetry is a decision rather than a default.
The second decision is the shunt itself. A bidirectional measurement needs a shunt with a low thermal EMF, because the seebeck voltage across the terminals appears as an offset that flips sign with temperature and looks exactly like current. Two terminal resistors in the same body are the usual answer. Where a pack monitoring chain is being rebuilt, our amplifier cross reference lists the bidirectional families by gain and reference arrangement, and the BOM shortage recovery page covers how a missing gain option is bridged.
Buyer questions on the INA2181A3IDSQR
What reference voltage should the pins see? Half the converter reference for a symmetric range, or a lower value when most of the current flows one way. The reference sets the zero point and therefore the headroom in each direction.
Can the two channels use different references? Yes, each channel has its own. That is useful when one channel measures a charge path and the other a discharge path at different scales.
Is the DSQ body different from the DSG body? Yes, 10 pins against 8 and a different land pattern. The bidirectional function needs the reference pins, which is why the body is wider.
Availability and ordering notes
The active row is the lettered WSON 10 string at 3000 pieces with NIPDAU and moisture level 1, and the plain row prints a different packing column in the same table. That pattern repeats across this family, so the order code is quoted with its letter and the body is confirmed from the label. The reel size and the moisture class go on the date code management note that travels with the shipment. A bidirectional channel also needs its reference decoupled, because noise on that pin appears directly as a zero offset on the current reading.