INA2180A4IDSGR
Product Specifications
INA2180A4IDSGR
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA2180A4IDSGR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA2180A4IDSGR: two 200 V/V channels for small shunt drops
The INA2180A4IDSGR is the highest gain dual in the INA180 family, 200 V/V per channel, in a WSON 8 pin body of 2 mm by 2 mm. Each channel reads a shunt between 0.2 V below ground and 26 V above it from a 2.7 V to 5.5 V supply. Offset is 150 uV maximum at 0 V common mode and 500 uV at 12 V, offset drift is 1 uV per degree, gain error is 1 percent maximum and bandwidth falls to 105 kHz at this gain, the slowest of the four options. The dual package draws 500 uA maximum.
Gain 200 is the row for a shunt that has to stay small. With a 5 milliohm shunt, 10 mV of drop corresponds to 2 A, and at gain 200 that 10 mV becomes 2 V, which is a comfortable span on a 3.3 V converter. The same shunt at gain 20 would give 200 mV and a resolution five times worse, which is the difference between measuring a load and detecting that one exists. The A4 row also carries the lowest bandwidth in the family, so it suits monitoring and not fast overcurrent protection.
Key data for the INA2180A4IDSGR
| Gain | 200 V/V per channel, the highest of the four options, with 20, 50 and 100 below it |
| Input | Common mode minus 0.2 V to plus 26 V per channel, independent of the 2.7 V to 5.5 V supply |
| Accuracy | Offset 150 uV maximum at 0 V and 500 uV at 12 V, 1 uV per degree drift, 1 percent gain error |
| Bandwidth | 105 kHz at gain 200 with a 10 pF load, 355 kHz at gain 20 and 150 kHz at gain 100 |
| Supply | 2.7 V to 5.5 V, 500 uA maximum for both channels, single 0.1 uF bypass |
| Output | Voltage output per channel, rail to rail within a few tens of millivolts at light load |
Body, marking and reel data
| Body | DSG, WSON 8 pin, 2 mm by 2 mm with an exposed pad that goes to the ground plane |
| Reel | 2500 pieces on a large reel for the A4 row, with a lettered counterpart printed obsolete |
| Finish | NIPDAUAG, moisture level 2 at 260 C with a one year floor life |
| Marking | 25HY on the A4 row, four characters that identify the dual die and the gain |
| Temperature | Minus 40 C to 125 C across the family, industrial rows only on this document |
Where gain 200 is worth the lost bandwidth
Two channels at 200 V/V is a power monitoring pair: one channel on the input rail and one on the output, so the system can report efficiency rather than guess it. At 105 kHz the part follows a load step in about 10 us, which is fast enough to catch a converter entering current limit and slow enough that switching ripple is averaged out rather than aliased. That is exactly the profile of a telemetry channel.
The offset specification at 12 V common mode is the number to watch. 500 uV at gain 200 is 2.5 uA referred to a 200 milliohm shunt, so a reading of zero still has a floor. Calibrating that floor out at one temperature works until the board warms, which is why the 1 uV per degree drift figure matters as much as the offset itself. Where a customer needs a tighter floor, the ultra low offset families are listed next to this one in our amplifier cross reference, and the safety stock planning page covers how the two gain options are stocked together.
Buyer questions on the INA2180A4IDSGR
Is the A4 row available in the VSSOP body? The lettered VSSOP rows of this family exist for the A3 gain, and the A4 VSSOP counterpart prints as obsolete. For the A4 gain the WSON body is the practical route.
What shunt value does gain 200 suit? Between 1 and 10 milliohm for amp level currents. At 10 milliohm the full scale drop is 10 mV at 1 A and the output is 2 V, which uses most of a 3.3 V converter's input range.
Does moisture level 2 mean a bake is needed? Only after a year on the shelf or after the bag has been open long enough to exceed the floor life. Level 1 rows of the same family do not carry that clock.
Availability and ordering notes
The A4 WSON row is active at 2500 pieces with NIPDAUAG and moisture level 2, marking 25HY, while the lettered counterpart of the same string prints as obsolete against the VSSOP body. That combination means the gain and the body are not independent choices in practice. We quote the active row, confirm the marking on the reel label and record the moisture class on the date code management note.