INA190A3IRSWR
Product Specifications
INA190A3IRSWR
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA190A3IRSWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA190A3IRSWR: gain of 100 with a 15 microvolt maximum offset
The INA190 is a bidirectional current sense amplifier with a zero drift front end, a 1.7 V to 5.5 V supply, a 0.1 V to 40 V common mode range and an enable pin. The A3 member has a gain of 100 V/V. Its offset is 3 microvolts typical and 15 microvolts maximum, which is the tightest in the family, drift is 10 nanovolts per degree typical, and input bias current is 0.5 nA. Common mode rejection is 132 dB typical and 150 dB minimum, so a measurement on a 36 V rail is not disturbed by the rail moving.
Quiescent current is about 65 microamps enabled and 150 nanoamps in shutdown, which is what makes the part usable in a product that runs from the battery it monitors. Gain error is 0.06 per cent typical and 0.3 per cent maximum on the A2 to A4 members, reference rejection is specified per gain so a reference that drifts does not appear as a current error, and the output swings to within 20 mV of the positive rail and 1 mV of ground on a 1.8 V supply. Bandwidth at a gain of 100 is 37 kHz.
Key data for the INA190A3IRSWR
| Gain | 100 V/V fixed, with 25, 50, 200 and 500 V/V members in the same family |
| Offset | 3 microvolts typical and 15 microvolts maximum, drift 10 nanovolts per degree typical |
| Rejection | Common mode 132 dB typical and 150 dB minimum, supply rejection 1 to 5 microvolts per volt |
| Current | About 65 microamps enabled and 150 nanoamps in shutdown, with the output high impedance when disabled |
| Accuracy | Gain error 0.06 per cent typical and 0.3 per cent maximum on the A2 to A4 members, 0.01 per cent linearity |
| Bandwidth | 37 kHz at a gain of 100, 45 kHz at the lower gains and 35 kHz at the gain of 500 |
Body, marking and reel data
| Body | The catalogue string carries the RSW suffix, which the addendum ties to the 10 pin UQFN body |
| Rows | The plain RSW row prints against the thin SOT-23 body and the UQFN row prints with a G4 suffix, both active |
| Reel | 3000 pieces on a large reel for the UQFN row, 180 mm carrier, moisture level 1 |
| Grade | Ambient minus 40 C to 125 C, with the Q1 automotive string documented separately |
Why the maximum offset is the number to quote
A typical offset of 3 microvolts is a production average, and a purchase order buys the maximum. At a gain of 100 the 15 microvolt maximum becomes 1.5 mV at the output, which is 0.15 per cent of a 1 V full scale and small enough that many circuits skip a calibration step. That is the practical difference between this part and a monitor with a 50 or 170 microvolt maximum, where the same gain produces 5 mV or 17 mV of output error before any signal.
The low quiescent current and the enable pin complete the picture for a portable product: the channel can be off between readings and the offset still holds when it comes back, because the zero drift front end does not need a warm up and the figure after each enable is the one the electrical table prints. Where a customer needs the automotive qualification, the Q1 string carries it in the SC70 body. Our power management cross reference lists the family by gain and body, and the supplier quality audit page covers what is checked before a lot ships.
Buyer questions on the INA190A3IRSWR
Which body does the RSW suffix mean? The addendum prints the plain RSW row against the thin SOT-23 and the UQFN row with a G4 suffix. Both are active, so the body has to be named on the purchase order rather than inferred from the suffix alone, before a schedule is booked.
Does the enable pin affect the offset? No. The front end settles to the same offset after each enable because the auto zeroing runs at start up, so a scanned channel does not need a warm up period before its reading is valid.
How does it behave with a 36 V rail? The common mode range reaches 40 V and the rejection is 132 dB typical, so a 36 V rail is inside the window. The supply still has to come from a 5.5 V or lower source.
Availability and ordering notes
This string needs the body confirmed at the ordering stage, because the suffix maps to two different packages in the addendum. We confirm the body, the reel size and the marking on every first order and record the confirmation on the quote, which is the same check we run on the rest of this family through the OEM procurement review.