INA188IDRJR
Product Specifications
INA188IDRJR
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA188IDRJR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA188IDRJR: a zero drift instrumentation amplifier with gain from 1 to 1000
The INA188 is an instrumentation amplifier that uses an auto zeroing front end to reach a low offset with almost no drift, and a voltage noise density of 12 nV per root hertz that stays flat down to dc. Gain is set by one external resistor with the industry standard equation, one plus 50 kilohm divided by the gain resistor, so any gain from 1 to 1000 is available from a single component. The output swings rail to rail, and the reference pin allows the output to be shifted for single supply operation or used for a calibration offset.
What the auto zeroing buys is a channel that does not need a periodic zero correction. A thermocouple amplifier with a conventional front end accumulates an offset that has to be measured by shorting the input, and that measurement is a moving target as the enclosure warms. The INA188 moves the offset down to a level where a single factory calibration holds for the life of the instrument, and the 0.25 microvolt peak to peak noise in the 0.1 Hz to 10 Hz band means the low frequency drift of the amplifier is not visible against the sensor.
Key data for the INA188IDRJR
| Gain | One plus 50 kilohm over RG, so any gain from 1 to 1000 with one external resistor |
| Noise | 12 nV per root hertz voltage noise density, flat to dc, plus 0.25 microvolts peak to peak in the low band |
| Offset | Auto zeroed front end, specified for low offset and near zero offset and gain drift over temperature |
| Output | Rail to rail, with a reference pin for level shifting in single supply systems or for calibration |
| Input | Radio frequency filter friendly inputs, so a series resistor and a capacitor can be added without offset |
| Supply | Split rails, wide range, output able to drive the converter directly in a 16 to 24 bit channel |
Body, marking and reel data
| Body | DRJ, SON 8 pin with the exposed pad, 1000 pieces on a large reel, 330 mm carrier |
| Sibling | INA188ID in SOIC 8 pin, tube of 75 and 2500 piece reel, for boards with a wider pad geometry |
| Finish | NIPDAU, moisture level 2 with a one year floor life on the SOIC rows, level 1 on the SON row |
| Grade | Ambient minus 40 C to 125 C, wider than the audio and older instrumentation families in the catalogue |
Where zero drift replaces a chopper stage
A precision channel built from a general purpose amplifier and a chopper stabiliser uses two packages, a clock and a filter, and the chopper's switching artefacts land in the same band as the signal. The INA188 puts the auto zeroing inside one package with the resistor network already matched, so the offset and the gain drift are handled together and the switching residue is placed above the band of interest. That is the reason it appears in thermocouple, strain gauge and low side shunt channels that have to hold a calibration for years.
The gain resistor is the accuracy limit above a gain of about 100, so a 0.1 per cent resistor with 25 ppm per degree is the normal choice in a calibrated instrument. Where a customer is replacing a discontinued precision amplifier, our amplifier cross reference lists the instrumentation families by noise, drift and gain method, and the drop in verification page sets out the test sequence for a channel that has to hold its calibration.
Buyer questions on the INA188IDRJR
What resistor gives a gain of 100? With the standard equation, a gain of 100 needs about 505 ohm between the gain pins. The data sheet table gives the value for each standard gain, and the resistor tolerance becomes the gain error at that point.
Is the SON body the same as the SOIC? Same die and same electrical table, different package and pad geometry. The SON body is 1000 pieces on a reel and the SOIC body is 2500, so the packing changes with the body.
Does it work with a single supply? Yes, with the reference pin set above ground so the output stays inside the swing. The input common mode range then has to be checked against the rail, as with any instrumentation amplifier.
Availability and ordering notes
Both bodies are active, with the SON row at 1000 pieces on a large reel and the SOIC rows at 75 in a tube and 2500 on a reel. The exposed pad on the SON body has to be soldered to a copper area for the thermal path, which is the one mechanical difference that catches a first build. We quote the body and the packing together and confirm the pad requirement with the customer's assembly process through the PCBA quote checklist.