Contact Us

INA183A2IDBVR

Brand: Texas Instruments
Texas Instruments INA183A2IDBVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA183A2IDBVR — Power Management & Signal Chain | Superb Automation

INA183A2IDBVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA183A2IDBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA183A2IDBVR: the gain of 100 member of the zero drift monitor family

The A2 suffix in the INA183 family is the gain of 100 V/V option. With the same 25 microvolt typical offset, the same 2.7 V to 26 V common mode range and the same 83 microamp quiescent current as the A1, it doubles the output for a given shunt drop and halves the shunt needed for a target full scale. A circuit that wants 2.5 V at 10 A can use a 2.5 milliohm shunt at this gain instead of a 5 milliohm shunt at the lower one, which halves the loss in the shunt without changing the amplifier.

Bandwidth falls to 30 kHz at this gain, and the slew rate stays at 0.4 volts per microsecond, so the settling time for a full scale step grows with the output swing. For a battery gauge or a power monitor that averages over milliseconds, that is not a limitation. For a fast overcurrent trip, the A1 member with its 80 kHz bandwidth is the better fit, which is why the family is offered in three gains rather than one.

Key data for the INA183A2IDBVR

Gain100 V/V fixed, so a 10 mV shunt drop gives 1 V and a 2.5 milliohm shunt carries a 10 A full scale
Offset25 microvolts typical and 170 microvolts maximum over temperature, 0.5 microvolts per degree maximum drift
Common mode2.7 V to 26 V, rejection 100 dB minimum at 10 mV of sense voltage, independent of the supply
Bandwidth30 kHz at a gain of 100 against 80 kHz at the A1 gain of 50, with the same 0.4 V per microsecond slew
SupplyTaken from the IN+ pin, 83 microamps typical and 130 microamps maximum quiescent current
AccuracyGain error within 0.4 per cent over temperature, nonlinearity 0.01 per cent, 25 nV per root hertz of noise

Body, marking and reel data

BodyDBV, SOT-23 5 pin, 3000 pieces on a large reel, 180 mm carrier, 2.9 mm by 1.6 mm footprint
Marking2BSQ on the A2 row, distinct from 2BRQ on the A1 and the third code on the A3, so the gain is visible
FinishSN on the rows that print a finish, moisture level 2 with a one year floor life at 260 C
GradeAmbient minus 40 C to 125 C, with the A3 member of the same family sharing the body and the reel

Choosing between the three gain options

The gain is chosen from the shunt that the thermal budget allows, not from the output range. A 20 A rail on a 1 milliohm shunt gives 20 mV, which at a gain of 100 is 2 V and uses the converter range well; the same rail at a gain of 50 gives 1 V and wastes half the range. A 1 A rail on a 100 milliohm shunt gives 100 mV, which at a gain of 100 would ask for 10 V and clip, so the lower gain or a smaller shunt is the answer. Working the choice from the shunt rather than from the part number is why the same family appears in three places on one board.

The other consideration is the offset multiplied by the gain. At a gain of 100 the 25 microvolt typical offset is 2.5 mV at the output, which is 0.1 per cent of a 2.5 V full scale, and the 170 microvolt maximum is 17 mV or 0.7 per cent. A circuit that needs better than that at the low end calibrates at test, and the calibration then holds because the drift is small. Our power management cross reference lists the gain options and the pin to pin cross reference page confirms that all three share the footprint.

Buyer questions on the INA183A2IDBVR

Can the A2 replace an A1 without a board change? Yes. Same body, same pinout, same reel. The gain doubles, so the reading at the converter doubles and the software scale factor has to change with it.

Why is the bandwidth lower than the A1? The family uses one compensation scheme and the bandwidth scales down as gain rises, 80 kHz at 50, 30 kHz at 100 and 14 kHz at 200. The slew rate is the same on all three.

What happens above 26 V of common mode? The part is not specified there and the input stage can be damaged. A 48 V rail needs a different monitor, or a divider that keeps the sense pins inside the window with the accuracy loss that implies.

Availability and ordering notes

All three gains are active in the addendum, in the same SOT-23 body, at 3000 pieces on a large reel. That means a product family can use one footprint across several current ranges and only the marking and the software constant change. We keep the three codes on one quote so the customer can compare the shunt and the gain together, and the date code and lot records travel with the shipment through the date code management process.