Contact Us

INA180A4IDBVR

Brand: Texas Instruments
Texas Instruments INA180A4IDBVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA180A4IDBVR — Power Management & Signal Chain | Superb Automation

INA180A4IDBVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA180A4IDBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA180A4IDBVR: 200 V/V current sense amplifier in the five pin SOT-23 body

INA180A4IDBVR is a single channel voltage output current sense amplifier with a fixed gain of 200 in a SOT-23 body of 5 pins. This is the highest gain member of the single channel family, so it turns a shunt drop of a few millivolts into a span a converter can read. The common mode window reaches 26 V independent of the supply, the supply runs from 2.7 V to 5.5 V, and the five pin body is offered in two pin orders so the same die fits either board.

Order code and package

INA180A4IDBVRSOT-23 DBV body, 5 pins, 3000 pieces on a large reel, Active, part marking 1AAD, tin plated lead finish, moisture level 1 unlimited floor life
INA180A4IDBVTthe same die and body, 250 pieces on a small reel, for a prototype build
INA180A4IDBVR.Bprinted at 250 pieces on a small reel in the same addendum despite the R suffix, so the packing has to be named on the order
Sibling gainsA1 is 20 V/V, A2 is 50 V/V and A3 is 100 V/V, all in the same five pin body with the same pin orders
Body size2.90 mm by 1.60 mm, pin order A with the output on pin 1 and pin order B with the output on pin 5

Electrical parameters that decide the application

Gain200 V/V, fixed on the die, one per cent maximum gain error over temperature, 20 ppm per degree of gain drift
Common mode rangeminus 0.2 V to 26 V, independent of the supply voltage
Offset voltageplus or minus 150 uV maximum at a common mode of 0 V, plus or minus 500 uV maximum at 12 V
Offset drift1 uV per degree maximum
Common mode rejection100 dB typical, 84 dB minimum from 0 V to 26 V
Supply range and current2.7 V to 5.5 V, 260 uA maximum for the single channel, 300 uA across temperature
Outputswing to within 40 mV of ground and within 0.02 V of the supply at a 10 kOhm load, 2 V per us slew rate
Input bias current50 uA typical on the summing node, 100 uA maximum over temperature
Temperature rangeminus 40 to plus 125 degrees ambient

Family variants and how they differ

Pin order Apin 1 output, pin 2 ground, pin 3 IN+, pin 4 IN minus, pin 5 supply
Pin order Bpin 1 supply, pin 2 ground, pin 3 IN+, pin 4 IN minus, pin 5 output
A4 against A3200 V/V against 100 V/V, one step more gain for a shunt drop half the size
Bandwidth notethe family figure of 355 kHz typical is printed once and belongs to the lowest gain member; the document carries no separate bandwidth row per gain, so the 200 V/V response should be checked on the bench
Dual and quad membersINA2180 in VSSOP and WSON, INA4180 in TSSOP, each in the same four gains

Points to check before this part goes on a BOM

At 200 V/V a ten millivolt shunt drop becomes two volts, which fills a 3.3 V converter without a second stage. The same gain multiplies the input offset: 150 uV becomes 30 mV at the output, so the offset rather than the gain error sets the floor on what the reading can resolve near zero current.

The gain error is specified at one per cent over the full temperature range, and the gain drift is 20 ppm per degree. That combination means a board calibrated at room temperature stays inside about half a per cent over a hundred degree swing, which is usually enough for a protection threshold and not enough for a metering claim.

The common mode window is independent of the supply, so a 3.3 V logic board can sense a 26 V bus on the high side with no second supply. That is the arrangement used on a battery stack or a telecom line where the sense point sits far above the logic rail.

The two pin orders are not interchangeable at assembly. A board built for order A and a reel of order B parts will not work, and only the marking separates them, so the pin order belongs on the purchase order and on the incoming inspection sheet.

The input bias current of 50 uA typical flows in the summing node and appears as a voltage across the external source resistance. A 100 ohm filter resistor in front of the input adds 5 mV of error at that current, which is a hundred times the offset, so any input filter has to be sized against the bias current rather than against the bandwidth alone.

Where the highest gain helps and where it hurts

The high gain member exists for a shunt drop in the low millivolt range, typically a low side shunt on a small motor or a battery monitor where the resistive loss has to stay small. On a 1 milliohm shunt at 5 A the drop is 5 mV, which becomes 1 V at the output with this part and only 250 mV with the 50 V/V member.

The cost is headroom. A 40 A pulse on the same shunt produces 200 mV of input and 40 V at the output, so the amplifier saturates well before the current reaches its peak, and the recovery from saturation is what determines how fast the controller sees the fault clear. A board that expects both a fine low current reading and a large fault current needs a clamp on the output or a lower gain member.

Offset at the output, not at the input

Every figure in the electrical table is referred to the input, so the error a converter sees is the input figure multiplied by the gain. At 200 V/V the 500 uV maximum at a 12 V common mode becomes 100 mV at the output, which on a 3.3 V converter is three per cent of the span. That is the reason a high gain member on a high side sense needs either a calibration step or a converter with a wider reference.

The pin order question at second source

Both orders carry the same die and the same electrical table, and the difference is only which pin the output lands on. On a two layer board that is a five minute change; on a dense board it is a rework, so the order code should be fixed before the artwork is released and the marking should be on the incoming inspection sheet.

Where this order code fits

Motor control, battery monitoring, power management, lighting control, overcurrent detection and solar inverters are the applications the vendor names, and the highest gain member is the one used where the shunt drop has to stay in the low millivolt range. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

What shunt value suits this gain? One that produces a shunt drop of a few millivolts at the current of interest, because 200 V/V turns 10 mV into 2 V, which fills a 3.3 V converter.

Does it sense a 24 V rail from a 3.3 V supply? Yes. The common mode window reaches 26 V independent of the supply, which leaves 2 V of margin on a 24 V rail.

Can the gain be changed on the board? No. The gain is fixed by the order code, so a different range needs a different part number.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.