INA180A3IDBVR
Product Specifications
INA180A3IDBVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA180A3IDBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA180A3IDBVR: voltage output current sense amplifier with a gain of 100
INA180A3IDBVR is a bidirectional current sense amplifier in a SOT-23 body of 5 pins. It measures a shunt on either side of the load, accepts a common mode range from minus 0.2 V to 26 V, and converts the differential voltage to a voltage output with a fixed gain. The A3 suffix sets that gain at 100 V per V. The A and B families use two different pinouts, so the suffix letter matters as much as the gain.
Order code and package
| INA180A3IDBVR | DBV body, SOT-23-5, 3000 pieces on a large reel, active, marking 1A9D |
| INA180A3IDBVT | the same part at 250 pieces on a small reel, marking 1A9D |
| INA180A2IDBVR and A4IDBVR | the gain 50 and gain 200 members of the same family, 3000 piece reels |
| INA180B3IDBVR | the same gain in the B pinout, which is not interchangeable with the A pinout |
Electrical parameters that decide the application
| Gain | 100 V per V on the A3 suffix, against 20, 50 and 200 on the A1, A2 and A4 |
| Common mode range | minus 0.2 V to plus 26 V, independent of the supply |
| Offset voltage | plus or minus 150 uV maximum at zero common mode, plus or minus 500 uV maximum at 12 V |
| Offset drift | 1 uV per C maximum |
| Gain error | plus or minus 1 per cent maximum |
| Supply | 2.7 V to 5.5 V, with a maximum quiescent current of 260 uA on the single channel part |
| Bandwidth | 350 kHz on the A1 member, 105 kHz on the A4 member per the application section, so the A3 sits between them |
| Slew rate | 2 V per us |
| Temperature range | minus 40 to plus 125 C, moisture level 1 unlimited floor life |
Family variants and how they differ
| A1 gain 20 | 350 kHz, the widest band member |
| A2 gain 50 | middle of the range |
| A3 gain 100 | the part on this page |
| A4 gain 200 | 105 kHz, the highest gain and the narrowest band |
| B suffix | same gains in the B pinout, which swaps the supply and ground pins against the A pinout |
Points to check before this part goes on a BOM
The offset voltage is quoted at two common mode points because it moves. It is 150 uV maximum at zero common mode and 500 uV maximum at 12 V, so a circuit that measures a shunt sitting on a 12 V rail has to budget three times the error of one that measures near ground.
The pinout letter is not a packing code. A and B devices have different pin assignments, and the document states that explicitly, so a B part dropped into an A footprint will not work even though the gain and the package are the same.
The supply current of 260 uA maximum is a real constraint on a battery product. It is the whole amplifier, not a quiescent figure per channel, and it is the reason the part is chosen over a discrete difference amplifier in a product that sleeps most of the time.
Bandwidth falls as gain rises, and the document gives the two ends: 350 kHz on the gain 20 member and 105 kHz on the gain 200 member. A 100 V per V part therefore sits in the middle of that range, and a control loop built around the gain 20 bandwidth will be unstable if the gain is raised later without rechecking the loop.
The common mode range extends 0.2 V below ground, which is what allows a low side shunt to be measured during a recirculation event when the ground of the load dips under the board ground.
The quiescent current of 260 uA is the maximum for the single channel part, and the dual and quad members of the family draw more. On a battery product that sleeps for weeks the difference between 260 uA and a discrete difference amplifier with a matched resistor network is the difference between a product that lasts a season and one that lasts a month.
The output is a voltage, not a current, so the load on the output is the input of whatever converter follows. A 12 bit ADC with a 100 kOhm input impedance loads the output enough to matter at the top of the range, which is why the document specifies the output swing with a defined load rather than open circuit.
The gain of 100 is a fixed resistor ratio inside the part, trimmed at test. That is the reason the gain error is plus or minus 1 per cent and not a resistor tolerance sum, and it is also the reason the part cannot be re-ranged in the field: a build that needs a different full scale needs a different suffix, not a different external resistor.
The two pinout families exist because the first generation of the part was laid out for one arrangement of supply and ground and a later revision swapped them. A board that was laid out for the B pinout and is built with an A part will show a short from supply to ground on first power up, so the suffix letter belongs in the bill of materials as a separate field.
How to read an offset figure at two common mode points
A current sense amplifier is a difference amplifier with a trimmed input stage, and the trim holds best near the common mode it was trimmed at. Quoting 150 uV at zero and 500 uV at 12 V is the vendor telling you which end of the range costs accuracy, and the percentage error at a given shunt depends on which end the circuit sits at.
The gain error of plus or minus 1 per cent is a maximum over temperature, not a typical. Combined with the offset term it sets the smallest shunt voltage the circuit can resolve, which on a 100 V per V part with a 3.3 V output is a 33 mV full scale and a resolution floor set by the 500 uV of offset rather than by the ADC.
What happens above the supply rail
The common mode range of minus 0.2 V to plus 26 V is independent of the 2.7 to 5.5 V supply, which means the amplifier measures a shunt on a 24 V rail while running from 3.3 V. That independence is the feature, and it is also the reason the input stage is the most expensive part of the die and the reason the offset moves between zero and 12 V of common mode.
The 0.2 V below ground matters on a low side shunt during a recirculation event, when the load current flows through a body diode and pulls the local ground below the board ground. A part that clamps at ground reads zero through that interval, and a motor control loop that integrates the current sees a false zero once per switching cycle.
Where this order code fits
Motor control, battery monitoring, power management, lighting control, over current detection and solar inverters are the applications the vendor lists, and all of them need a shunt measurement that stays linear above the supply rail. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
What gain does the A3 suffix give? 100 V per V. The A1, A2 and A4 suffixes give 20, 50 and 200.
Can it measure a high side shunt at 24 V? Yes. The common mode range is minus 0.2 V to plus 26 V and it is independent of the 2.7 to 5.5 V supply, so a 24 V rail is inside the window.
Is the B version a drop in for the A version? No. The document states that A devices use pinout A and B devices use pinout B, so the gain and package match but the pin assignment does not.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.