INA180A2IDBVR
Product Specifications
INA180A2IDBVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA180A2IDBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA180A2IDBVR: 50 V/V current sense amplifier in the five pin SOT-23 body
INA180A2IDBVR is a single channel voltage output current sense amplifier with a fixed gain of 50 in a SOT-23 body of 5 pins. It turns a shunt drop into an analogue voltage with a matched resistor network on the die, so the gain is set by the part number and not by four external resistors. The common mode window reaches 26 V independent of the supply, the supply runs from 2.7 V to 5.5 V, and the five pin body comes in two pin orders that let the same part fit two different boards.
Order code and package
| INA180A2IDBVR | SOT-23 DBV body, 5 pins, 3000 pieces on a large reel, Active, part marking 1A8D, tin plated lead finish, moisture level 1 unlimited floor life |
| INA180A2IDBVT | the same die and the same body, 250 pieces on a small reel, for a prototype build |
| INA180A2IDBVR.B | printed at 250 pieces on a small reel in the same addendum despite the R suffix, so the reel size has to be named on the order |
| Sibling gains | the A1 member is 20 V/V, the A3 member 100 V/V and the A4 member 200 V/V, all in the same five pin body |
| Body size | 2.90 mm by 1.60 mm, two pin orders, A with the output on pin 1 and B with the output on pin 5 |
Electrical parameters that decide the application
| Gain | 50 V/V, fixed on the die, one per cent maximum gain error over temperature, 20 ppm per degree of gain drift |
| Common mode range | minus 0.2 V to 26 V, independent of the supply voltage |
| Offset voltage | plus or minus 150 uV maximum at a common mode of 0 V, plus or minus 500 uV maximum at 12 V |
| Offset drift | 1 uV per degree maximum |
| Common mode rejection | 100 dB typical, 84 dB minimum from 0 V to 26 V |
| Supply range and current | 2.7 V to 5.5 V, 260 uA maximum for the single channel, 300 uA across temperature |
| Output | swing to within 40 mV of ground and within 0.02 V of the supply at a 10 kOhm load, 2 V per us slew rate |
| Bandwidth | 355 kHz typical on the 20 V/V member with a 10 pF load, 197 kHz minimum over temperature |
| Input bias current | 50 uA typical on the summing node, 100 uA maximum over temperature |
| Temperature range | minus 40 to plus 125 degrees ambient |
Family variants and how they differ
| Pin order A | pin 1 output, pin 2 ground, pin 3 IN+, pin 4 IN minus, pin 5 supply |
| Pin order B | pin 1 supply, pin 2 ground, pin 3 IN+, pin 4 IN minus, pin 5 output |
| A2 against A1 | 50 V/V against 20 V/V; the higher gain suits a smaller shunt drop, the lower gain a wider current range |
| A2 against A3 and A4 | 100 V/V and 200 V/V members sit in the same body, so gain is the only electrical difference in the family |
| Dual and quad members | INA2180 in VSSOP and WSON, INA4180 in TSSOP, for a board that senses more than one phase |
Points to check before this part goes on a BOM
The matched resistor network on the die is the whole point of the part. Four external resistors with one per cent tolerance would give a gain error far above the one per cent quoted here, and the drift of four separate parts would add instead of cancelling, so the fixed gain part is both smaller and more accurate than the discrete difference amplifier it replaces.
The offset has two numbers because the input stage sees two different common mode conditions. At 0 V the offset is 150 uV, and at 12 V it is 500 uV, so a high side sense on a 12 V rail carries more than three times the error of a low side sense on the same board. That is the number to use when the shunt drop is only a few millivolts.
The common mode window is independent of the supply. A 3.3 V rail can sense a 26 V bus, which is what makes the part usable on a telecom line or a battery stack without a separate high side supply.
The two pin orders matter at the second source stage. A board laid out for order A and a part ordered as order B will not work, and the marking is the only visible difference, so the pin order belongs on the purchase order next to the part number.
The assembly rows in the addendum are not uniform. INA180A2IDBVR is printed at 3000 pieces on a large reel, while the .B row of the same string is printed at 250 pieces on a small reel, and INA180B2IDBVR.B is marked obsolete. A production order therefore needs the reel size stated, not just the part number.
What a 50 V/V gain does to a 10 mV shunt drop
A 10 mV full scale drop becomes 500 mV at the output, which is a comfortable span for a 3.3 V converter and leaves room for an overcurrent headroom check. The same 10 mV on a 5 V supply wastes most of the converter range, so the gain has to be picked against the ADC reference rather than against the shunt alone.
The offset of 150 uV at a 0 V common mode is 1.5 per cent of that 10 mV drop, and 500 uV at 12 V is 5 per cent. At the low end of the range the offset, not the gain error, is what limits the usable resolution, and no amount of averaging in the host removes a fixed input offset.
What the 26 V window means on a 48 V system
The common mode window stops at 26 V, so a 48 V telecom rail cannot be sensed directly on the high side. The usual route is a low side shunt with the amplifier ground tied to the return, or a divided sense point, and both change the offset budget because the input bias current then flows through the divider. A board that has to look at a 48 V rail should establish the sense point before the part number is fixed.
Why the supply current figures are quoted twice
The 260 uA is the maximum for the single channel member, and the 300 uA is the same parameter across the full temperature range. A battery powered board that budgets on the room temperature number will be short at 125 degrees, and the dual and quad members draw 500 uA and 900 uA respectively, which is worth knowing before the channel count is fixed.
Where this order code fits
Motor control, battery monitoring, power management, lighting control, overcurrent detection and solar inverters are the applications the vendor names, and each of them needs one analogue current signal per phase feeding a controller that samples at its own rate. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
Does it work on the high side of a 24 V rail? Yes. The common mode window runs to 26 V independent of the supply, so a 24 V rail is inside the window with 2 V of margin, and the supply can stay at 3.3 V.
Can it measure current in both directions? The input is differential and the output is unipolar, so a bidirectional measurement needs a reference offset on the output, which the single channel body does not provide.
How is the gain chosen? By the part number: A1 is 20 V/V, A2 is 50 V/V, A3 is 100 V/V and A4 is 200 V/V, all in the same body.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.