Contact Us

INA134UA

Brand: Texas Instruments
Texas Instruments INA134UA is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA134UA — Power Management & Signal Chain | Superb Automation

INA134UA

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA134UA from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA134UA: a 0 dB audio line receiver in an eight pin SOIC, in a 75 piece tube

The INA134UA is a unity gain differential line receiver in an eight pin SOIC, sold in a 75 piece tube. It is one op amp and four laser trimmed 25 kΩ resistors, with a fixed gain of 1 V/V, 0.1 per cent gain error, 0.0001 per cent nonlinearity and 0.0005 per cent total harmonic distortion plus noise at 1 kHz. The job it does is turn a balanced line into a single ended signal while rejecting the ground difference between two chassis.

The audio rows are the reason it exists: minus 100 dBu of noise floor over 20 kHz, plus 23 dBu of headroom, 14 V per microsecond of slew and 3 microseconds of settling to 0.01 per cent. On a plus or minus 18 V supply the output swings to plus or minus 16 V, which is plus 26 dBu, so the headroom figure is met with 3 dB left over.

The INA134UA rows as the addendum publishes them

Part classUnity gain audio differential line receiver, trimmed 25 kΩ network
Vendor statusActive, production
Data sheetSBOS071, Burr-Brown PDS-1390A, July 1997
Addendum rowINA134UA, 75 pieces per tube
Gain1 V/V, 0 dB, fixed
Gain error0.1 per cent maximum, 0.02 typical
Gain nonlinearity0.0001 per cent of full scale
Total harmonic distortion plus noise0.0005 per cent at 1 kHz with a 10 V rms input
Noise floorMinus 100 dBu over a 20 kHz bandwidth
HeadroomPlus 23 dBu with distortion below 1 per cent
Input offset voltage1 mV maximum, 2 µV per degree drift
Common mode rejection90 dB typical at a plus or minus 31 V common mode
Input impedance50 kΩ differential and common mode
Bandwidth3.1 MHz small signal
Slew rate14 V per microsecond
Settling3 µs to 0.01 per cent after a 10 V step
OutputPlus or minus 16 V on plus or minus 18 V, 500 pF stable, 60 mA
Supply rangePlus or minus 4 V to plus or minus 18 V
Quiescent current2.4 mA typical, 2.9 mA maximum
BodySOIC, D outline, 8 pins
Moisture levelLevel 3, 260 degrees, 168 hour floor life

0 dB of gain on a trimmed network

INA134UA is a unity gain differential amplifier built for audio line receivers, and the whole function is four trimmed resistors around one op amp. The gain is 1 V/V fixed, the gain error is 0.1 per cent maximum and the nonlinearity is 0.0001 per cent of full scale with a 1 ppm per degree drift, so the network does not contribute a measurable distortion term. The input network is 50 kohm differential and 50 kohm common mode.

Building the same function from four 0.1 per cent resistors and an audio op amp is possible and usually cheaper in unit cost, and it is worse in every other way: four parts to place, four tolerances to stack, and a ratio match that depends on how the board heats. The integrated network is trimmed as a set, so the common mode rejection is a specification rather than a hope. That is what the part is bought for.

0.0005 per cent at 1 kHz and a noise floor of minus 100 dBu

The audio rows are the reason to read this sheet: total harmonic distortion plus noise is 0.0005 per cent at 1 kHz with a 10 V rms input, the noise floor is minus 100 dBu over a 20 kHz bandwidth, and the headroom is plus 23 dBu with distortion below 1 per cent. Those three numbers describe a line receiver that will not be the limiting stage in a console or a broadcast chain.

The noise figure is quoted per the amplifier plus the thermal noise of the resistor network, which is why it moves when the source impedance moves. At minus 100 dBu the residual is about 7.7 microvolts rms, and the output noise over the audio band is 7 microvolts rms, so the network is not the dominant term at ordinary source impedances. Beyond a few tens of kohm of source impedance the current noise and the network thermal noise take over.

16 V of swing on 18 V rails and a 500 pF load limit

The output of INA134UA swings to within 1.8 V of the positive rail and 1.6 V of the negative rail, so on plus or minus 18 V the usable span is plus or minus 16 V, which is plus 26 dBu and above the plus 23 dBu headroom figure. Continuous output current is 60 mA, enough to drive a 600 ohm load to that level, and the load capacitance limit is 500 pF, which is lower than the difference amplifier family and is the row that decides whether a cable can be driven directly.

A 500 pF limit means a shielded cable of a few metres needs a series resistor or a buffer, because a cable is 50 to 100 pF per metre plus the connector. The usual arrangement is 47 to 100 ohms in series at the output, which isolates the capacitance and costs nothing in the audio band. Without it the part is stable on the bench and rings on the installed cable, which is the failure that gets blamed on the board.

1 mV of offset, 90 dB of rejection and the ground loop it removes

Input offset on INA134UA is 1 mV maximum with a 2 microvolt per degree drift, which is large for a precision part and irrelevant for an audio line receiver, where the signal is volts. What matters is the 90 dB of common mode rejection at a plus or minus 31 V common mode, because that is the number that removes the ground loop between two chassis plugged into different outlets. At 90 dB a 1 V ground difference becomes 32 microvolts at the output.

The rejection holds only if the source impedances match. A balanced line with 50 ohm build out resistors on both legs and a 1 kohm imbalance from a faulty connector drops the rejection by an order of magnitude, which is audible as hum. That is why the input network is 50 kohm and why the two legs should be terminated the same way: the amplifier is not the problem, the cable and the connectors are.

2.9 mA per amplifier and the 150 degree per watt SO-8

Each channel of INA134UA draws 2.4 mA typical and 2.9 mA maximum, and the supply window runs from plus or minus 4 V to plus or minus 18 V. On a plus or minus 18 V supply that is about 100 milliwatts per channel dissipated in the package, and the junction to ambient figure is 150 degrees per watt in the SO-8 against 100 in the eight pin DIP, so the SO-8 runs 15 degrees hotter for the same current. In a rack at 50 degrees ambient that is still inside the 85 degree specification, but it is not inside it by much if two channels share a package.

The absolute maximum supply is 40 V total, the inputs survive 80 V, and the output is short circuit protected continuously to ground for one channel per package. On a dual, a short on one channel does not take the other with it because the two channels are independent, which the vendor states as a feature and which matters on a connector that can be miswired.

The UA reel, the PA tube and the dual INA2134

The current addendum lists one active row for the single: INA134UA at 2500 pieces on a large reel, moisture level 3, 168 hour floor life, minus 40 to plus 85 degrees. The eight pin DIP version INA134PA is published in the package table but has no active reel row, so a through hole build is a broker purchase rather than a catalogue line. The dual INA2134UA is the fourteen pin SOIC at 2500 pieces on a reel.

The 330 mm reel with a 12.4 mm tape width is the standard carrier for the eight pin body, and the parts are marked INA134UA. Because the tube row is not active, a prototype build of a few hundred boards either takes a reel or takes cut tape, and cut tape on a moisture level 3 part has to be baked before reflow if the exposure time is not recorded. That is the practical difference between this part and a part with an active tube row.

Buying INA134UA

The tube is a pilot quantity and the reel is the production quantity, and both are active for this part, which is not true of the eight pin DIP. A through hole build needs the PA body and that row is not carried on a reel, so a line that still uses a DIP is buying from stock rather than from a catalogue line.

The other consideration is the dual. The INA2134UA puts two independent channels in a fourteen pin SOIC with 117 dB of separation at 1 kHz, which is what a stereo pair wants; two singles cost two placements and two reels. Our pin to pin cross reference page covers the packages that share the footprint when a board is being re-spun.

Questions that arrive with this part number

Whether the gain can be changed is the first question, and it cannot: the network is fixed at 0 dB, and a channel that needs 6 dB of attenuation is the INA137 while a channel that needs 6 dB of gain is not this family at all. The second is whether the part can drive a cable, and it can only up to 500 pF, which is a few metres, with a 47 to 100 ohm series resistor at the output.

The third is the offset, 1 mV maximum with 2 µV per degree of drift. That is large for a precision part and irrelevant for a line receiver, where the signal is volts; it becomes relevant only if the receiver is used as a DC instrumentation block, which the applications section allows and the specification does not encourage.