Contact Us

INA114BU

Brand: Texas Instruments
Texas Instruments INA114BU is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA114BU — Power Management & Signal Chain | Superb Automation

INA114BU

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA114BU from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA114BU: the B grade precision amplifier in a 16 pin SOIC

The INA114BU is the combination of the B grade offset bin with the 16 pin wide body SOIC, which is the version most new boards use when they need the tighter bin and a surface mount body. The die is the three amplifier instrumentation amplifier with a gain range from 1 to 10,000, 50 µV of maximum offset at high gain, 0.3 µV per degree of drift, 2 nA of bias current, 115 dB of common mode rejection at a gain of 1000, and 40 V of input protection. The supply range is 2.25 V to 18 V total and the temperature range is minus 40 to plus 85.

The carrier is a tube of 40, the body is 10.3 by 10.3 millimetres including pins, and the moisture level column on the tube row reads not applicable while the reel row of the same body reads level 3. The finish is nickel palladium gold, which wets with both tin lead and lead free solder.

The INA114BU rows as the addendum publishes them

Part classThree amplifier instrumentation amplifier, B grade, surface mount
Vendor statusACTIVE, production data
Data sheetSBOS014B, revised January 2026
Gain equationG = 1 + 50 kΩ divided by RG
Gain range1 to 10,000 V/V
Input offset voltage50 µV maximum at high gain
Offset drift0.3 µV per degree maximum at high gain
Input bias current2 nA maximum
Common mode rejection at G = 1000115 dB minimum
Input overvoltage protection40 V without damage
Supply range2.25 V to 18 V total
BodySOIC, DW outline, 16 pins
Carrier, tube row40 pieces in a tube
Carrier, reel row1000 pieces on a large tape and reel under the slash one K string
RoHSYes
Lead finishNickel palladium gold
Moisture level, tube rowNot applicable to this package type
Moisture level, reel rowLevel 3 at 260 degrees, 168 hour floor life
Temperature rangeMinus 40 to plus 85 degrees
Part markingINA114BU
Revision rowINA114BU.B, same body and quantity
Status of both rowsActive, production data

The tube row of this string is the one to quote when the customer is building a few hundred boards, and the reel row is the one to quote above that. Both are active and both carry the same die, so the only thing that changes is the handling after the parts leave the vendor.

The B bin at a gain of 1000, and the arithmetic of a 50 Ω resistor

At a gain of 1000 the gain resistor is 50.05 Ω and the resistor tolerance becomes the gain error. A 0.1 per cent part gives a 0.1 per cent gain error before the amplifier is counted, and the amplifier's own gain error at that gain is specified in the same order. A channel that needs 0.25 per cent at a gain of 1000 therefore needs both a tight resistor and the B bin, and the two together are cheaper than a calibration step at the end of the line.

The 50 Ω value also sets a floor on the parasitic resistance that matters. A solder joint is a milliohm, a short trace is a few milliohms, and at 50 Ω a 10 mΩ error is 0.02 per cent. That is inside the tolerance of any resistor worth using, which is why the gain network at high gain is more forgiving than it looks, provided the resistor is placed at the pins rather than at the far end of a trace.

Thermal behaviour on a flat body

The SOIC body sits closer to the copper than a plastic DIP, so the junction to ambient path is shorter and the part runs cooler for the same dissipation. On a precision amplifier the practical consequence is that the drift seen on the bench is closer to the drift specified in the data sheet, because the specified drift assumes the die is at the ambient temperature and a hot package is not. A 10 degree rise on a 0.3 µV per degree part is 3 µV, which is a sixth of the offset budget on a 10 mV channel.

The other side of the same coin is that the body picks up heat from neighbouring parts. A voltage regulator within a centimetre of the amplifier will put a thermal gradient across the die, and a gradient across the input pair is an offset. The placement rule is to keep the amplifier away from anything that dissipates more than a fraction of a watt, and to orient the part so the two inputs sit on the same isotherm.

Where this part sits between the INA114 and newer families

The INA114 family is a general purpose precision amplifier with a 2.25 V supply floor and a 10,000 gain range. A newer family in the same category, such as the one the vendor lists as a successor for the INA118, offers a lower supply, a smaller body and a better drift, and it is not pin compatible. A customer who is moving to a new board should compare the two rather than substitute, because the pin out and the gain equation differ and the trim pins in the older family have no equivalent.

Where the board cannot change, the INA114BU is the right answer and the newer part is a future project. Where the board is new, the newer part is worth the evaluation, and the comparison should include the drift over the temperature range rather than only the room temperature offset.

Buying INA114BU

The string is active, the tube is 40, and the reel is 1000 pieces. A customer who needs the B bin on a reel should confirm the slash string with the vendor rather than assume the tube string with a quantity suffix, because the reel is a separate row and a separate string on the addendum.

A build that mixes the A and B bins on the same board is possible and is sometimes done to save cost on channels that do not need the tighter bin. The marking on the body is the only way to tell them apart after the fact, and a rework station that mixes a tube of each will produce a board that passes at room temperature and drifts differently at the cold end.

Questions that arrive with this part number

Whether the BU can be used at a gain of 1 is the first question, and it can, with the gain resistor left open. Whether the part needs a trim at unity gain is the second, and the answer depends on the full scale: at 1 V the offset is negligible, at 10 mV it is 0.5 per cent of full scale.

The third is whether the 40 V protection survives a reverse supply connection. It does not, because the protection is on the inputs rather than on the supply pins, and a reversed supply will destroy the part through the substrate.

For a customer choosing between the bins and the bodies, our amplifier cross reference page lists the comparisons we run, and the BOM sourcing page explains how a mixed bin order is kitted and labelled.

The reference pin deserves the same treatment on this body as on the through hole version, with one addition: the trace from the reference pin to the converter reference should not run under the part, because the body sits close to the board and the copper underneath is a thermal path as well as an electrical one. Keeping that trace on the same layer as the input and away from the output pins keeps both the impedance and the thermal gradient under control.

A second point on a flat package is the paste and the standoff. A SOIC that sits flat has a short lead length and a good thermal path, and it also has less compliance when the board flexes. A board that is mounted on a chassis with a single screw near the amplifier will flex at temperature, and the offset of a precision part moves with the stress. Two screws rather than one, and a part placed away from the mounting hole, is cheap insurance on a channel that has to hold 50 µV.