Contact Us

DRV8912QPWPRQ1

Brand: Texas Instruments
Texas Instruments DRV8912QPWPRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV8912QPWPRQ1 — Power Management & Signal Chain | Superb Automation

DRV8912QPWPRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV8912QPWPRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV8912QPWPRQ1: Twelve Half Bridges on One SPI Bus for Automotive Body Loads

DRV8912QPWPRQ1 is an automotive multi channel half bridge driver in a HTSSOP (PWP) body of 24 pins. It puts twelve independently controlled half bridges on one package, each rated 1 A RMS and 6 A when paralleled, working from 4.5 V to 32 V with a 40 V absolute maximum. Configuration and diagnostics go over a 16 bit SPI bus at 5 MHz with daisy chain support, and every channel reports open load, overcurrent and overtemperature faults back to the controller.

Order code and package

Ordering stringDRV8912QPWPRQ1
Family documentDRV8904-Q1 to DRV8912-Q1, SLVSEC9C, revised February 2020
PackageHTSSOP (PWP), 24 pins, with an exposed pad
Reel and packing3000 pieces on a large reel, NiPdAu lead finish
Moisture levelLevel 3, 260 C peak, 168 hours of floor life
Body markingDRV8912
Temperature rangeminus 40 to plus 125 degrees
QualificationAEC-Q100
Outputs12 half bridges, configurable as high side, low side or full bridge
Interface16 bit SPI at 5 MHz, daisy chain capable
PWM generatorsEight programmable generators, used for current limiting or dimming
Fault reportingnFAULT pin plus per channel status over SPI

Electrical parameters that decide the application

Supply range4.5 to 32 V, 40 V absolute maximum
Output current1 A RMS per half bridge, 6 A maximum for paralleled outputs
On resistance0.75 Ω typical and 1.1 Ω maximum per FET at 13.5 V and 0.5 A, 1.5 Ω at 125 C
Overcurrent trip1.3 A minimum, 1.8 A typical, 2.3 A maximum
Overcurrent deglitch6 us minimum, 10 us typical, 14 us maximum at the default setting
Supply undervoltageRising 4.0 to 4.5 V, falling 3.8 to 4.3 V, 200 mV of hysteresis
Logic undervoltageRising 2.4 to 2.95 V, 75 mV of hysteresis
Sleep current1.5 uA
Thermal warning150 to 170 C
Thermal shutdown175 C typical, 20 C of hysteresis
Open load detect5 kΩ to 400 kΩ thresholds depending on the load connection
Open load deglitch2 to 4 ms in continuous mode, 300 us in PWM mode
Logic levels3.3 V and 5 V compatible

Family variants and how they differ

DRV8904-Q14 half bridges, 2000 pieces on a reel
DRV8906-Q16 half bridges, 2000 pieces on a reel
DRV8908-Q18 half bridges, 2000 pieces on a reel
DRV8910-Q110 half bridges, 2000 pieces on a reel
DRV8912-Q112 half bridges, 3000 pieces on a reel, the part on this page
Full bridge useTwo adjacent half bridges drive a brushed motor or one stepper winding
Paralleled useSeveral half bridges on one load reach the 6 A ceiling
Low current detectionThe active open load mode reduces the threshold by about eleven times and raises the low side resistance to about 7.5 Ω

Points to check before this part goes on a BOM

The per output rating is 1 A RMS, and that is a thermal statement about the package as much as the silicon. Twelve channels each carrying an amp in a 24 pin body adds up to a dissipation that the exposed pad has to remove, and the 6 A figure applies only to outputs that are paralleled so that the current shares across several FETs. A body module that drives twelve independent lamps at 1 A each is well outside what the package can hold continuously.

Overcurrent is detected per channel and the trip window is wide, from 1.3 A to 2.3 A. That is deliberate, because the same die has to protect a small lamp and a motor, but it means the trip cannot be used as a current measurement. A channel that is expected to run at 1 A sits close to the bottom of the trip window, and a load with an inrush pulse will cross it unless the deglitch setting is chosen carefully.

The active open load detection mode is the feature that makes this part useful in a body controller, and it comes with two costs. The threshold falls by about eleven times, to roughly 120 mA minimum, which is what allows a small LED or a relay coil to be checked, and the low side resistance rises to about 7.5 Ω, which raises the dissipation in that mode. The thermal budget has to account for the detection mode separately from the driving mode.

Daisy chain SPI is what keeps the pin count down on a body controller with several of these devices. Each part passes the data on to the next, so four devices share one chip select and one clock, and the controller shifts a frame of 64 bits instead of four separate transactions. The timing requirements are tight at 5 MHz, with 40 ns of setup and 60 ns of hold on the data line, so the trace length between devices matters.

The part is qualified to AEC-Q100 and rated to 125 degrees, which is the reason it exists rather than a consumer driver with the same function. The same twelve half bridges in a consumer body would be cheaper, and would also have no per channel diagnostics, no open load detection and no specification over the automotive temperature range.

What a body controller does with twelve half bridges

Door locks, mirror fold, seat adjustment, window lift, HVAC flaps and lamps are the usual loads, and the common thread is that each one needs a direction and a diagnosis rather than a precise speed. Twelve half bridges give six full bridges, which covers three axes of seat movement plus a lock and a mirror, and the SPI diagnostics replace the discrete fault wiring that a relay based controller would need.

The programmable PWM generators are used to hold a motor at a fixed current during a stall, which is how a window lift detects an obstruction without a separate sensor. The generator chops the channel at a frequency set over SPI, and the channel current is compared with the limit in the same way that a dedicated driver would do it.

Reading the diagnostics

Every channel reports an open load, an overcurrent and an overtemperature flag, and the SPI frame also carries the global supply and charge pump status. That is enough to distinguish a broken lamp from a shorted harness without measuring anything analog, which is the point of the part in a module that has no room for a shunt per channel.

The flags are latched until they are read, and the recovery behaviour after an overcurrent depends on the configuration. A channel that retries automatically will keep a shorted load oscillating between drive and fault, which is visible in the status register as a repeating pattern, while a latched channel stays off until the controller clears it. The choice is made per channel over SPI.

Where this order code fits

The part fits an automotive body module that has to drive several small motors, lamps or relays and report their state over a shared serial bus, in a package that can take the underhood temperature range. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

How many full bridges does this give? Twelve half bridges make six full bridges, or twelve independent high side or low side outputs. The configuration is static in the sense that adjacent pairs are wired together on the board, so the split between full bridges and single ended outputs is a board decision.

Can the outputs be paralleled for more current? Yes, up to 6 A total, and the current shares across the paralleled FETs because they are on the same die and at the same temperature. The overcurrent detection still works per channel, so a fault on one of the paralleled outputs shows up individually.

Is the part suitable for a 12 V or a 24 V system? Both. The operating range starts at 4.5 V and the absolute maximum is 40 V, which covers a 24 V rail with load dump margin only if the external clamp holds the transient below that figure. A 12 V system has plenty of headroom.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.