Contact Us

DRV8847SPWR

Brand: Texas Instruments
Texas Instruments DRV8847SPWR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV8847SPWR — Power Management & Signal Chain | Superb Automation

DRV8847SPWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV8847SPWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV8847SPWR: A Dual Bridge With a 1 Ohm Pair and an I2C Option in the Same Footprint

DRV8847SPWR is a dual H bridge for brushed motors, steppers and solenoids in a TSSOP (PW) body of 16 pins. It runs from 2.7 V to 18 V, delivers 1 A per bridge and 2 A with the bridges in parallel, and measures 1 Ohm across the high and low side FETs above 5 V. The S in this string is the member with an I2C port for diagnostics, the plain DRV8847PWR is the pin controlled one, and both sit in the same 16 pin body with the same pinout.

Order code and package

Ordering stringDRV8847SPWR, large reel, 2000 pieces
Family documentDRV8847, SLVSE65C, revised December 2023
PackageTSSOP (PW), 16 pins, no thermal pad
Lead finishNIPDAU or SN, both published for this body
Moisture levelLevel 2, 260 C, one year floor life
Body marking8847SPW
Temperature rangeminus 40 to plus 125 degrees
Pin controlled siblingDRV8847PWR, 2000 piece reel, marking 8847PW
PowerPAD siblingDRV8847PWPR, HTSSOP with a pad, marking 8847PWP
WQFN siblingDRV8847RTER, 3000 piece reel, marking 8847
Torque scaler siblingDRV88471RTER, WQFN, marking 88471

Electrical parameters that decide the application

Supply range2.7 to 18 V
Driver current per bridge1 A root mean square at 25 C ambient
Driver current in parallel2 A root mean square
FET resistance at 12 V520 mOhm at 25 C and 700 mOhm at 85 C, first bridge
FET resistance at 5 V530 mOhm at 25 C and 740 mOhm at 85 C
FET resistance at 2.7 V690 mOhm at 25 C and 950 mOhm at 85 C
Sleep current1.7 uA at 12 V and 25 C, 2.5 uA at 85 C
Active current3 mA typical at 12 V with the inputs low
Wake time1.5 ms from nSLEEP high to an output transition
Input thresholds0.6 V low below 7 V of supply, 1.0 V above it, 1.6 V high
Propagation delay400 ns typical, 100 to 600 ns window
Output dead time200 ns
Body diode drop1.1 V at 0.5 A
Current regulation20 us fixed off time on the ISEN pins
Torque scalarhalves the regulated current when the TRQ pin is pulled low
Protectionundervoltage, overcurrent, open load and thermal shutdown on nFAULT

Family variants and how they differ

DRV8847PWRPin controlled, no I2C, same body and pinout
DRV8847SPWRI2C diagnostics, the part on this page
DRV8847PWPRHTSSOP with a PowerPAD, same die, better thermal path
DRV8847RTERWQFN body, 3000 piece reel
DRV88471RTERWQFN body with the torque scaler and no I2C
InterfacesFour pin, two pin, parallel bridge or independent bridge
What the bus addsRegister level fault reporting and multi slave addressing

Points to check before this part goes on a BOM

The TSSOP body has no thermal pad and that is the first constraint. The 1 A rating is a root mean square figure at 25 C ambient with the part soldered to a board, and the same die in the HTSSOP with a pad carries more because the heat has somewhere to go. A board that needs 1 A continuously in a closed box should take the PWP body, and a board that needs 0.5 A can stay in the TSSOP without a heatsink.

The two bridges are not identical in resistance. At 12 V the first measures 520 mOhm at 25 C and the second 450 mOhm, which is a real difference of about 13 percent and comes from the internal routing rather than from the silicon. A stepper that uses both windings alternately sees a slightly different voltage on each, which shows up as a position error that a microstepping controller can correct only if it knows which bridge is which.

Current regulation on this part is a fixed 20 us off time chopper rather than a constant current loop. The ISEN pin voltage is compared with an internal threshold, the bridge turns off for 20 us, and the current decays through the body diodes. That is enough to hold a stepper at a set current and it is not enough to hold a motor at a precise torque, because the ripple depends on the winding inductance and the supply.

The I2C member exists for diagnostics rather than for control. The bridge is still driven from the input pins, and the bus reports which bridge saw an overcurrent, whether a load is open and whether the die has been hot. On a bank of eight solenoid drivers that is the difference between replacing a board and replacing a valve, and it costs two pins and a pull up.

What the pin options do to a board

The four pin interface uses two inputs and two enables per bridge, which is the simplest to drive from a microcontroller with spare GPIO. The two pin interface uses one direction and one enable, which halves the pin count and puts the commutation table in firmware. Parallel bridge mode ties both bridges to one input pair for 2 A into a single load, and independent mode drives two loads that have nothing to do with each other.

The torque scaler pin halves the regulated current without changing the sense resistor. On a printer that has a draft mode and a quality mode, that is one GPIO instead of a second sense resistor and a second bill of materials line, and the current in the low torque mode is set by the same resistor that sets the high torque mode.

The TSSOP body is the whole thermal argument. Sixteen pins of 0.65 mm pitch carry very little heat, and the 1 A figure assumes a board with copper on both sides and a still air ambient of 25 C. Inside a solenoid manifold at 60 C the same part carries about 700 mA before the junction reaches its limit, which is why the HTSSOP with a pad exists in the same family and fits the same footprint outline.

The I2C address is set by a resistor rather than by a pin strap, so eight drivers can share a bus without a decoder. The bus runs at standard or fast mode, the registers report per bridge faults, and the part answers while the bridge is switching. A controller that polls all eight every ten milliseconds adds about a millisecond of bus traffic, which is cheap compared with the wiring it replaces in a bank of valves.

Where this order code fits

Solenoid and stepper boards that want fault reporting without a bigger package start from the power management cross reference page Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Does the I2C member need the bus to run? No. The bridge is controlled from the input pins exactly like the plain member, and the bus only carries diagnostics. A board that leaves SCL and SDA unconnected still drives motors, it just cannot read why a fault occurred.

Can both bridges be paralleled for 2 A? Yes, that is the published parallel mode. The inputs are tied together and the outputs joined, and the 2 A root mean square figure assumes the TSSOP body at 25 C. Inside an enclosure the thermal path, not the rating, sets the usable current.

Why does the second bridge measure lower resistance? The two bridges sit on different parts of the die and the internal metal is not symmetric. The vendor publishes both sets of numbers, and a board that depends on matching between the two bridges has to allow for the difference rather than assume one figure applies to both.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.