Contact Us

DRV8836DSSR

Brand: Texas Instruments
Texas Instruments DRV8836DSSR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV8836DSSR — Power Management & Signal Chain | Superb Automation

DRV8836DSSR

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV8836DSSR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV8836DSSR: Two 1.5 A H Bridges From a 2 V Rail, in a 3 mm Package

DRV8836DSSR is a dual low voltage H bridge for two DC motors or one stepper in a WSON (DSS) body of 12 pins. It works from 2 V to 7 V, delivers 1.5 A per bridge and 3 A with the two bridges in parallel, and measures 305 mOhm across the high and low side FETs at 5 V. The 2 V floor is what puts it on a two cell alkaline pack or a single lithium cell, and the 95 nA sleep current is what keeps a battery powered toy from draining on the shelf.

Order code and package

Ordering stringDRV8836DSSR, large reel, 3000 pieces
Family documentDRV8836, SLVSB17D, revised April 2016
PackageWSON (DSS), 12 pins, 3.00 mm by 2.00 mm
Lead finishNIPDAU
Moisture levelLevel 1, 260 C, unlimited floor life
Body marking836
Temperature rangeminus 40 to plus 85 degrees on the addendum
Rows of the same stringDRV8836DSSR.B and DRV8836DSSRG4, both active, same reel
Driver countTwo independent H bridges with a shared supply and separate inputs
Control pins per bridgeTwo inputs and one enable, plus an nSLEEP for the pair

Electrical parameters that decide the application

Supply range2 to 7 V
Output current per bridge1.5 A maximum
Output current with bridges paralleled3 A
FET resistance high plus low at 5 V305 mOhm typical, 355 mOhm maximum
FET resistance high plus low at 3 V370 mOhm typical, 420 mOhm maximum
Sleep current40 nA typical, 95 nA maximum with the supply at 5 V
Active current1.7 mA typical, 2.5 mA maximum at 50 kHz and no load
Undervoltage lockout2 V rising, 1.9 V falling
Input thresholds0.5 times the supply for a high, with 100 kOhm pulldowns
Overcurrent trip1.6 to 3.5 A per bridge
Overcurrent timing1 us of deglitch, then a retry every 1 ms
Output dead time100 ns
Output rise and fall20 to 188 ns rise, 8 to 30 ns fall
Thermal shutdown150 to 180 C

Family variants and how they differ

DRV8836Dual bridge, 2 to 7 V, 1.5 A, 305 mOhm, the part on this page
DRV8835Dual bridge, 2 to 11 V, 1.5 A, phase and enable interface
DRV8833Dual bridge, 2.7 to 10.8 V, 1.5 A, PWM interface only
DRV8834Stepper indexer with two bridges, 2.5 to 10.8 V, microstepping
What the dual givesTwo motors or one bipolar stepper from one package
What parallel gives3 A into one load with both bridges driven from one input pair
What is missingNo current regulation and no charge pump, so the supply sets the torque

Points to check before this part goes on a BOM

The 2 V floor is the whole reason this part exists in a toy or a handheld. Below about 2.5 V the gate drive of a conventional bridge stops enhancing the FETs, the resistance rises and the motor stalls at exactly the point where the battery is weakest. This part keeps its 370 mOhm at 3 V and still switches at the 2 V lockout, so the last third of the battery curve is usable rather than a slow crawl.

Parallel mode is not automatic. The two bridges have to be driven from the same inputs, with IN1 and IN3 tied and IN2 and IN4 tied, and the outputs joined at the motor terminals. Both bridges then carry half the current, which halves the conduction loss and distributes the heat across the 3 mm package. The 3 A figure assumes the two bridges are matched, which they are on one die, but it does not assume they share perfectly, so a 3 A continuous load is still a thermal question.

The overcurrent response is a retry, not a latch. A short trips at 1.6 to 3.5 A, the bridge turns off for 1 ms and then tries again, which means a jammed mechanism produces a 1 kHz buzz rather than a silent dead channel. That is easier to diagnose in the field but it also heats the die, because every retry pushes the full current into the short for the deglitch time. A mechanism that can jam permanently needs the supply cut by the controller, not left to the driver.

Sleep is entered by the nSLEEP pin rather than by the inputs, which matters when the controller is also asleep. With nSLEEP low the whole part draws under 95 nA, so a toy left in a box for a year loses under 1 mAh. The wake time is in the microsecond range and the outputs come up in the state the inputs define, so a firmware that pulls nSLEEP high before setting the input pins can produce a short pulse on the motor at every wake.

What the board has to provide

Two 0.1 uF ceramics, one at the supply pin and one at the bridge supply, plus bulk capacitance sized for the stall current of both motors. At 3 A with 305 mOhm the bridge drops nearly a volt, so a 3 V rail cannot deliver 3 A into a winding that needs 2 V; the arithmetic of the resistance and the motor sets the real ceiling, not the current rating.

The WSON body has an exposed pad and it is the only thermal path. Twelve pins in a 3 mm by 2 mm outline give almost no lead area, so a board that does not solder the pad to a ground plane runs the part at the thermal shutdown within seconds at 1 A. Four vias of 0.3 mm under the pad into the ground plane is the minimum that makes the 1.5 A rating real.

A two cell alkaline pack is the case this part was written for. Two fresh cells give 3.2 V, the pair falls to 2.4 V at the end of life, and a driver that needs 2.7 V to keep its FETs enhanced stops working while the cells still have a third of their energy left. The 2 V lockout here means the toy keeps running until the cells are genuinely flat, and the 370 mOhm at 3 V keeps the torque usable rather than dropping to a crawl. A single lithium cell is the other case, with a 4.2 V top and a 3.0 V floor, and it fits inside the window without a boost converter.

Where this order code fits

Robot and toy projects that moved from a 5 V rail to a single cell usually compare this part on the power management cross reference page Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Can it drive a bipolar stepper? Yes. Each bridge drives one winding and the two input pins per bridge set the polarity, so the controller produces the four step states. There is no indexer inside, so microstepping and current control have to come from the firmware and a chopper outside the part.

What happens below 2 V? The undervoltage lockout turns the outputs off at 1.9 V falling and they come back at 2 V rising. Between those points the part is in a defined state rather than switching weakly, which is what protects a lithium cell from being over discharged by a stalled motor.

Is the 85 degree ambient rating a problem? It rules out engine bay and most industrial cabinet work. Inside a handheld product the ambient stays under 50 C and the junction is the number to watch, which reaches 150 C shutdown only if the pad is not soldered or the load is above 1 A continuously.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.