Contact Us

DRV8802QPWPRQ1

Brand: Texas Instruments
Texas Instruments DRV8802QPWPRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV8802QPWPRQ1 — Power Management & Signal Chain | Superb Automation

DRV8802QPWPRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV8802QPWPRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV8802QPWPRQ1: A Dual H Bridge for Two DC Motors With Four Selectable Current Levels

DRV8802QPWPRQ1 is an automotive dual H bridge DC motor driver with two bit winding current control in a HTSSOP (PWP) body of 28 pins. It runs from 8 V to 45 V, drives two DC motors at 1.6 A peak or 1.1 A RMS each with proper heatsinking, and controls the winding current in four levels through a two bit parallel interface, so a motor can be run at full, half or quarter strength without a PWM signal from the host. The outputs use N channel FETs on both sides with a charge pump for the high side, and the on resistance is 0.63 Ohm for the high side and 0.65 Ohm for the low side at 25 degrees. A 3.3 V reference output is included for the current setting divider.

Order code and package

Ordering stringDRV8802QPWPRQ1, HTSSOP, large reel
Family documentDRV8802-Q1, SLVSCI2A, June 2014, first revision
QualificationAEC-Q100 grade 1, minus 40 to plus 125 degrees ambient
ESD classHBM level 2, CDM level C4B
PackageHTSSOP (PWP), 28 pins with PowerPAD
Bridgestwo independent H bridges, one motor each
Controlparallel digital, two bits per bridge set four current levels
Decay pinselects brake or coast when the bridge is disabled
Reference3.3 V output, 1 mA, for the current setting divider
Fault outputnFAULT, open drain, low on a fault

Electrical parameters that decide the application

Supply range8 to 45 V on each VM pin
Undervoltage lockout7.8 V falling, 8.2 V rising
Output current1.6 A peak, 1.1 A RMS per bridge with heatsinking at 24 V and 25 C
High side on resistance0.63 Ohm typical at 24 V and 1 A, 0.9 Ohm maximum
Low side on resistance0.65 Ohm typical at 24 V and 1 A
On resistance at 125 C0.85 Ohm typical, 1 Ohm maximum
Operating supply current5 mA typical, 8 mA maximum at 24 V with PWM below 50 kHz
Sleep current10 uA typical, 20 uA maximum
Overcurrent trip1.8 A minimum, 5 A maximum
Current sense trip voltage469 mV typical, 445 to 492 mV
Sense amplifier gain5 V per V
Current sense blanking100 us after a switching edge
Thermal shutdown150 C minimum, 160 C typical, 180 C maximum
Reference output3.3 V, 3.1 to 3.5 V, up to 1 mA
Input thresholds2.1 V high, 0.7 V low, 0.45 V hysteresis

Family variants and how they differ

DRV8802-Q1dual bridge, 8 to 45 V, two bit current control, the part on this page
DRV8801-Q1single bridge, 8 to 38 V, with a current sense output
DRV8873-Q1single bridge, 4.5 to 38 V, integrated current sense and SPI diagnostics
DRV8874-Q1single bridge with integrated current sense in a smaller body
DRV8847dual bridge at lower voltage with a simpler interface
DRV8428stepper driver with microstepping, for a different motor type
What this part addstwo bridges in one body with a shared reference and fault pin
What it does not havemicrostepping, SPI diagnostics or integrated current sense output

Points to check before this part goes on a BOM

Two bits for four current levels is an old interface and it is still the right one for a replacement part. A mirror or a flap motor in a vehicle is driven from a body controller that already has two or three GPIOs per motor, and asking that controller to generate a PWM signal with the right duty cycle is a firmware change. With this part the levels are selected by the same two pins that used to select direction, and the current limit is set by a resistor divider on the reference pin. That is why the part survives in products that are otherwise being reworked around it: the harness and the firmware stay the same.

The current control works by chopping the bridge when the voltage across the sense resistor reaches a fraction of the reference. The amplifier gain is 5, the trip is 469 mV, and the divider on the reference pin sets the fraction, so the four levels come from four divider settings rather than four reference voltages. The blanking time of 100 us after each switching edge is what stops the current spike of the commutation from tripping the comparator, and it also sets the minimum pulse width, which is why the chopping frequency is low compared with a modern driver. At 24 V into a 10 Ohm motor the ripple at that frequency is a few tens of milliamps, which is audible as a hum but not as a torque problem.

The 1.6 A peak rating is not the continuous rating, and the difference is thermal. Each bridge dissipates the square of the current times the sum of the two FET resistances, so 1 A gives about 1.3 W at 25 degrees and 1.7 W at 125 degrees, and 1.6 A gives more than 3 W before any switching loss. In the 28 pin HTSSOP with a PowerPAD soldered to a copper area, that is manageable for intermittent loads such as a mirror fold that runs for two seconds, and it is not manageable for a pump that runs continuously. The 1.1 A RMS figure assumes proper heatsinking, which in practice means several square centimetres of copper on both layers connected to the pad with vias.

Protection covers the faults a vehicle harness produces. Overcurrent trips between 1.8 and 5 A, thermal shutdown at 160 degrees typical, undervoltage lockout at 8 V, and the nFAULT pin goes low and stays low until the fault clears, which lets the controller distinguish a transient from a short. What the part does not have is a diagnostic register, so a controller that needs to know which bridge faulted has to test them one at a time. The decay pin selects brake or coast on disable, and that choice matters for a flap that has to hold position against a spring rather than drift back when the drive is released.

Setting the current limit with the internal reference

The 3.3 V reference pin exists so the current setting divider does not have to depend on the controller supply. A divider from that pin to ground sets the reference for the internal comparator, and the two bit input selects one of four fractions of it, so the four current levels scale together with one resistor pair. The reference is rated for 1 mA, which is why the divider should be in the tens of kilohms rather than the hundreds of ohms, and why nothing else should be powered from that pin. Because the trip point is 469 mV at the sense amplifier input with a gain of 5, the divider values translate into a winding current through the shunt, and that calculation has to be done at the highest ambient temperature the motor sees, where the shunt resistance rises.

Where this order code fits

Mirror adjust and fold, HVAC flaps, seat pumps, small pumps and any pair of DC motors driven from a body controller with limited GPIO. The four level current control suits loads that need a low power hold rather than full torque. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Can the two bridges be paralleled for one bigger motor? Not directly. The two bridges are independent and the current control is per bridge, so paralleling needs external current sharing that the part does not provide.

Does it need a charge pump capacitor? The charge pump is internal and needs only its own bypass capacitors as shown in the typical application circuit, no external diode.

What sets the four current levels? The divider on the reference pin, with the two bit input selecting one of four fractions of that reference.

Is the 3.3 V reference able to power a microcontroller? No. It is rated for 1 mA and exists to set the current level divider.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.