DRV8801AQRMJRQ1
Product Specifications
DRV8801AQRMJRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV8801AQRMJRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV8801AQRMJRQ1: An Automotive Full Bridge That Reads Its Own Current Out of a Sense Pin
DRV8801AQRMJRQ1 is an automotive DMOS full bridge motor driver in a QFN (RMJ) body of 16 pins. It drives a brushed motor or one winding of a stepper from 8 V to 38 V, sources and sinks 2.8 A at peak, and brings a voltage out on the VPROPI pin that is proportional to the current in the bridge, so a controller can close a current loop without a shunt amplifier. The output stage is a full H bridge of N channel FETs with a charge pump for the high side gates, and the overcurrent limit is set by one resistor on the SENSE pin.
Order code and package
| Ordering string | DRV8801AQRMJRQ1 |
| Family document | DRV8801-Q1, SLVSAS7D, revised March 2021 |
| Package | QFN, 16 pins, 4.00 mm by 4.00 mm with an exposed pad |
| Reel and packing | 3000 pieces on a large reel |
| Temperature range | minus 40 to plus 125 degrees, AEC-Q100 grade 1 |
| ESD classification | HBM level H2 and CDM level C4 |
| Interface | PHASE and ENABLE, with nSLEEP for the low power state |
| Current feedback | VPROPI output, a voltage proportional to the bridge current |
| Current limit setting | A resistor on SENSE sets the trip point |
| Published row in the addendum | DRV8801QRTYRQ1 in the RTY QFN body, 3000 pieces |
| String on this page | The A and RMJ letters are not printed in the addendum of revision D |
| Duty cycle | 100 per cent supported, the charge pump keeps the high side on |
Electrical parameters that decide the application
| Operating supply | 8 to 38 V on VBB |
| Peak output current | plus or minus 2.8 A |
| On resistance, sink driver at 2.8 A | 0.74 to 0.85 Ohm at 25 degrees junction |
| On resistance, source driver | 0.48 Ohm at 2.8 A and 25 degrees junction |
| On resistance, headline figure | 0.83 Ohm for the high side plus low side in series |
| Undervoltage lockout | 6.5 to 7.5 V with VBB rising |
| Overcurrent trip | About 3 A, set by the SENSE resistor and a 0.5 V threshold |
| Sense pin threshold | 0.5 V, with the resistor sized so the drop stays below it at rated current |
| Thermal warning | OTW at the warning level, with 15 degrees of hysteresis on the shutdown |
| Logic levels | 3.3 V and 5 V compatible inputs |
| Sleep | nSLEEP low shuts the internal circuits down, including the charge pump |
| Protection | Undervoltage, overcurrent, short to supply, short to ground, thermal warning and shutdown |
Family variants and how they differ
| DRV8801-Q1 | This part, one full bridge, automotive qualified |
| DRV8801 | The industrial version of the same function |
| DRV8800 | A lower current member with the same interface |
| DRV8871 | A single bridge with an internal current limit and no sense pin |
| DRV8873-Q1 | An automotive bridge with a serial port and integrated current sense |
| DRV8251 | A single bridge for a lower voltage rail |
Points to check before this part goes on a BOM
The order code on this page does not appear in the vendor addendum, which prints DRV8801QRTYRQ1 in the RTY body for every published row of revision D. The A and RMJ letters belong to an earlier body name, and a purchase order that quotes this string may come back as the RTY part. The page states the discrepancy rather than presenting the string as confirmed, and the code should be checked against a customer PO before a schedule is set.
VPROPI is the feature that saves a shunt, and it is an approximation. The pin outputs a voltage proportional to the current in the low side path, with a tolerance that is good enough for a torque limit and not good enough for a measurement. A current loop built on it drifts with temperature and with the supply, and a product that has to report amps needs a real shunt instead.
The SENSE resistor sets the trip point and also carries the whole bridge current, so it dissipates. With the 0.5 V threshold and a 0.2 Ohm resistor the trip is 2.5 A and the resistor burns 1.25 W at that current, which is more than the package can take in a small body. The resistor has to be a power type and its tolerance directly moves the trip point.
The on resistance figures are quoted at 2.8 A, which is the peak rating, so they already include the heating that comes with it. The sink driver is 0.74 to 0.85 Ohm while the source driver is 0.48 Ohm, and that asymmetry means a bridge driven in one direction runs hotter than in the other. A product that reverses often needs the thermal calculation for the worse direction.
The 38 V ceiling is above a 24 V rail with a regenerative spike but below a 36 V nominal rail at tolerance, and the undervoltage lockout at 6.5 to 7.5 V is above a 6 V rail. That puts the part in the 12 V and 24 V world, which is where most automotive actuators live, and keeps it out of a 48 V system without an external regulator.
Where an automotive full bridge is used
A throttle body, an exhaust gas recirculation valve, a seat motor or a mirror actuator is the target. The motor is brushed, the rail is 12 V, the bridge has to survive a short to ground on the harness, and the controller wants a rough current reading to detect a stall against the end stop. VPROPI gives that reading with no extra parts.
A stepper with two windings uses two of these parts, one per winding, driven with PHASE and ENABLE from a timer. The 100 per cent duty support matters at low speed, where a PWM chopper would otherwise need a minimum off time, and the charge pump keeps the high side gate up through a long on time.
What has to be checked before the order
The body and the order code first, because the published rows are in the RTY body and this string names RMJ. Confirm the code and the package with the vendor or the distributor, and treat any quotation that cannot show the exact string as unconfirmed.
The second check is the sense resistor and its thermal load. It carries the full bridge current, so a 0.2 Ohm part at 2.8 A dissipates 1.6 W and heats the board around the driver. A smaller resistor moves the trip point up, and a larger one moves it down, so the choice is a trade between protection and loss rather than a fixed value.
Where this order code fits
The part suits a 12 V or 24 V brushed actuator on a vehicle harness, where a rough current reading is enough to detect a stall and the board has no room for a shunt amplifier. Teams comparing it with a neighbouring part start from our Pin to Pin Cross Reference page, and teams replacing a part that has gone end of life start from the Obsolete Part Cross Reference Hub page.
Questions buyers ask
Is VPROPI accurate enough to measure current? No. It is a proportional voltage for a torque or stall limit, with drift over temperature and supply. A reading in amps needs a shunt and an amplifier.
Why is the order code not in the addendum? The addendum of revision D prints DRV8801QRTYRQ1 in the RTY body for every row, and the A and RMJ letters are not there. The string should be confirmed against the vendor or a customer purchase order before it is quoted.
Can it run at 100 per cent duty? Yes. The charge pump supplies the high side gate, so a static on command holds the bridge on instead of decaying the gate charge.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.