DRV8703DQRHBRQ1
Product Specifications
DRV8703DQRHBRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV8703DQRHBRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV8703DQRHBRQ1: An Automotive H Bridge Gate Driver With Eight Drive Levels Over SPI
DRV8703DQRHBRQ1 is a single H bridge gate driver for four external N channel MOSFETs in a VQFN (RHB) body of 32 pins. It drives four external FETs from 5.5 V to 45 V, holds the high side gate 11.5 V above the source with a charge pump, and sets peak gate current in eight steps between 10 mA and 240 mA so the switching edge is chosen rather than fixed. The SPI port also reaches the current shunt amplifier gains of 10, 20, 40 and 78, the PWM current regulation and a watchdog that turns the bridge off if the controller stops talking.
Order code and package
| Ordering string on the catalogue page | DRV8703DQRHBRQ1, large reel, 3000 pieces |
| Ordering string in the vendor addendum | DRV8703QRHBRQ1, an extra D in the catalogue string |
| Family document | DRV870x-Q1, SLVSDR9F, revised June 2026 |
| Package | VQFN (RHB), 32 pins, 5.00 mm by 5.00 mm |
| Lead finish | NIPDAU or SN, both published for this body |
| Moisture level | Level 3, 260 C, 168 hour floor life |
| Body marking | DRV8703 |
| Temperature range | minus 40 to plus 125 degrees ambient, AEC-Q100 grade 1 |
| Sibling without SPI | DRV8702QRHBRQ1, same body and reel, fixed 20 V per V amplifier |
| Tube row | DRV8703QRHBTQ1 exists in the addendum with no published quantity |
| Qualification | AEC-Q100 grade 1, Functional Safety-Capable documentation |
Electrical parameters that decide the application
| Gate driver supply range | 5.5 to 45 V, logic functional from 4.5 V |
| Gate to source voltage | 11.5 V typical above 13.5 V of supply |
| Peak source current | Eight steps, 10, 20, 50, 70, 100, 145, 190 and 240 mA |
| Peak sink current | Eight steps, 20, 40, 90 and upward in the same pattern |
| Active supply current | 5.5 to 12 mA at 13.5 V, no FETs switching |
| Sleep current | 14 uA at 25 C and 25 uA at 125 C |
| Internal regulator | 3.3 V at 30 mA, or 5 V at 30 mA by register |
| Charge pump output | 23.5 V typical at 13.5 V supply, 12 mA capability |
| Shunt amplifier gain | 10, 20, 40 and 78 V per V, selected by register |
| Shunt amplifier offset | 5 mV typical, 10 mV maximum |
| Reference input range | 0.3 to 3.6 V for the internal current chopping |
| Undervoltage lockout | on the supply and on the charge pump, both reported on nFAULT |
| Protection set | overcurrent, gate driver fault, thermal shutdown and a watchdog timer |
| PWM duty | 100% supported, because the charge pump runs continuously |
Family variants and how they differ
| DRV8702-Q1 | Same bridge, no SPI, gain fixed at 20 V per V, drive set by a resistor |
| DRV8703-Q1 | SPI member, gain and drive in registers, watchdog, the part on this page |
| Interface options | PH and EN, independent half bridge, or PWM on one pin |
| Gate fault detection | VGS and VDS monitors reported per FET |
| Watchdog | Turns the bridge off if the SPI traffic stops, which a safety case can use |
| Charge pump | Supports 100% duty, unlike a bootstrap only driver |
| What the SPI costs | Four pins and a configuration sequence at start up |
Points to check before this part goes on a BOM
The drive level has to be chosen from the FET and the loop, not from the maximum. A 240 mA source current turns a 100 nC gate in 400 ns, which on a 20 nH gate loop rings at 50 MHz and radiates. The same FET driven at 50 mA takes 2 us to switch, which is slow enough that the switching loss at 20 kHz becomes the thermal limit instead. The eight steps span that range so a single board can pass an emissions scan and still keep the FET cool at the chosen frequency.
The current regulation loop chops the bridge when the amplified shunt voltage reaches the reference. With a 1 mOhm shunt and a gain of 78, a 2 A current produces 156 mV, so a 150 mV reference sets the limit at about 1.9 A. The chopping off time is set in the same register block, and the value decides whether the current ripple stays inside the motor inductance or produces an audible whine at the chopping frequency.
The watchdog is a safety feature that also bites in development. If the controller stops writing to the SPI port within the window, the bridge turns off and the motor coasts. That is the right behaviour in a seat or a window lift, and it is a nuisance on a bench where the controller is being single stepped. The watchdog can be disabled by register, and a board that does so for production loses the diagnostic that a safety case would want.
The catalogue string and the vendor addendum disagree by one letter. This page is titled DRV8703DQRHBRQ1, while the addendum dated for this family prints DRV8703QRHBRQ1 for the 32 pin RHB body at 3000 pieces on a large reel, and no D appears anywhere in the published rows. A purchase order written from the title alone may come back as a non catalogue part or as a clarification, so the string should be confirmed against a customer part list before a schedule is quoted.
Level 3 moisture and a 5 mm QFN body mean the pad is the thermal path and the floor life is 168 hours. The gate drive loss at 20 kHz with 60 nC of gate charge and 11.5 V of drive is under 30 mW per FET, so the package is not the limit; the external FETs are. What the package does need is a solid ground under the pad, because the source of the low side FETs returns through it and any impedance there appears in series with the gate loop.
Where a gate driver beats an integrated bridge
A window lift motor draws 8 A at stall and 2 A running, and the FETs have to sit where the heat can leave the board. An integrated bridge in a 5 mm package cannot pass 8 A continuously, while four external FETs in DPAK or PowerPAK can be placed on the copper that suits them and the driver sits anywhere nearby. The same argument applies to a seat module with four motors, where one driver per motor and a shared microcontroller is the cheapest arrangement.
The external FET choice also decides the reverse battery behaviour. A bridge built from four N channel FETs passes current through the body diodes in the wrong polarity, so the module needs a reverse battery FET or a fuse, and the driver itself has to survive the supply going below ground during a load dump, which the 45 V ceiling and the charge pump lockout handle.
The drive level is set differently on the two members. The DRV8702-Q1 takes a resistor on the IDRIVE pin between 1 kOhm to ground and 1 kOhm to the regulator, giving 10 up to 240 mA of peak source current; the DRV8703-Q1 sets the same eight levels in a register. A board that wants to tune the edge after the first emissions scan needs the SPI member, and a board that fixes the value at prototype and never touches it again saves four pins with the resistor member.
Where this order code fits
Automotive body modules that need external FETs start from the power management cross reference page and the pin to pin table Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
Can the bridge hold 100% duty? Yes. The charge pump generates the gate supply continuously, so the high side FET stays enhanced indefinitely. A bootstrap driver cannot do this, which is why the part is chosen for a relay replacement or a load that has to be held on.
What happens if the SPI bus is not connected? The part powers up with default drive levels and gains and will drive a motor from the input pins, but the watchdog is active by default and the fault registers are not readable. A board that does not talk to the part should use the DRV8702-Q1 instead.
Does it need a shunt on every phase? One shunt in the low side path is enough for current regulation, because the bridge is a single H. The amplifier inputs are differential and rated to 1.2 V pulsed, so the shunt value and the gain are chosen together from the maximum current.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Date Code Management page sets out the checks that keep a substitute from failing on the bench.