Contact Us

DRV8702QRHBRQ1

Brand: Texas Instruments
Texas Instruments DRV8702QRHBRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV8702QRHBRQ1 — Power Management & Signal Chain | Superb Automation

DRV8702QRHBRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV8702QRHBRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV8702QRHBRQ1: automotive H-bridge gate driver for four external N-channel FETs in a 32 pin VQFN

DRV8702QRHBRQ1 is an AEC-Q100 grade 1 H-bridge gate driver in the 32 pin RHB body that runs from 5.5 V to 45 V, drives four external N-channel FETs with resistor programmed gate currents and a 17 V gate clamp, and supports 100 percent duty operation in a VQFN body of 32 pins. The DRV8702-Q1 drives one H-bridge built from four external N-channel MOSFETs. It accepts 5.5 V to 45 V, offers PH/EN, independent and PWM control interfaces, and holds 100 percent duty on the high side by way of the internal charge pump. Gate current is set by a resistor to ground or to the AVDD rail, which sets the switching slew rate, and the part carries AEC-Q100 grade 1 qualification for minus 40 C to 125 C ambient operation.

Order code and package

Order codeDRV8702QRHBRQ1
Functionsingle H-bridge gate driver for four external N-channel FETs
Operating supply voltage5.5 V to 45 V
Gate drive clamp17 V typical, 16.3 V to 17.8 V
Control interfacesPH/EN, independent H-bridge and PWM
Maximum applied PWM frequency100 kHz
Logic compatibility1.8 V, 3.3 V and 5 V
Package32 pin VQFN, RHB body
QualificationAEC-Q100 grade 1, minus 40 C to 125 C ambient
DocumentDRV870x-Q1 family data sheet

Electrical parameters that decide the application

Gate drive clamping voltage, positive16.3 V to 17.8 V, 17 V typical
Gate drive clamping voltage, negativeminus 1 V to minus 0.5 V, minus 0.7 V typical
Charge pump load current at 13.5 V0 to 12 mA
Charge pump load current at 8 V0 to 10 mA
Charge pump load current at 5.5 V0 to 8 mA
Reference input range for the shunt amplifier0.3 V to 3.6 V
AVDD external load current30 mA maximum
DVDD external load current30 mA maximum
Shunt amplifier output current5 mA maximum
Logic input voltage range0 V to 5.25 V
Ambient operating temperatureminus 40 C to 125 C

Points to check before this part goes on a BOM

The 17 V gate clamp is the number that decides which FETs can be trusted with this driver. It holds the gate source voltage below the 20 V limit that most N-channel FETs specify, including during a 45 V bus transient, and it is high enough above the 10 V plateau that the FET reaches its rated on resistance. A gate driven to the full 45 V rail would destroy the FET, so the clamp is doing protection work rather than trimming a level, and it is why the high side drive comes from a charge pump rather than from the bus.

Gate current is set by a resistor from the IDRIVE pin to ground or to the AVDD rail, and the resistor selects both the source and the sink current. The choice is an emissions decision as much as an efficiency one: a fast edge keeps switching loss low and radiates, a slow edge trades loss for a quieter spectrum. Because both the source and the sink current come from the same setting, the turn on and turn off edges move together unless the gate network is asymmetric, which is why a resistor in series with the gate is a separate tool from the IDRIVE setting.

One hundred percent duty operation needs the charge pump, and the pump has a finite load current. At 13.5 V it will supply 12 mA, at 8 V it is 10 mA and at 5.5 V it is 8 mA. That current has to cover the high side gate leakage and the gate charge of the FET at the switching frequency, so a large FET switched fast at 100 kHz from a 5.5 V rail is outside the pump's ability even though the part is rated for 100 kHz. Gate charge times frequency is the arithmetic that decides it, and a 100 percent duty hold has no switching loss to hide behind.

The shunt amplifier reference input accepts 0.3 V to 3.6 V, and the data sheet notes that operation below 0.3 V degrades accuracy. That makes the reference a deliberate choice: a unidirectional measurement sets it near 0.3 V and uses the full output swing for positive current, while a bidirectional measurement sets it at mid rail and gives up half the swing to the negative direction. The amplifier output can drive 5 mA, which is enough for a microcontroller input and not enough for a low impedance load.

AVDD and DVDD can each supply 30 mA to external circuitry, within the thermal budget. On an automotive actuator that is often used to power a Hall sensor or an encoder, which removes a regulator from the board. The limit is stated as 30 mA subject to power dissipation, so the same 32 pin body that carries the gate drive losses also carries this load, and the thermal calculation has to include it.

The three control interfaces are not three ways of saying the same thing. PH/EN drives the bridge with a direction signal and a magnitude signal, independent mode exposes all four gates and expects the controller to manage the dead time, and PWM mode takes a single duty signal. Independent mode is where shoot through becomes the controller's problem, because the driver's internal timing no longer decides the order in which the switches change state.

Grade 1 qualification is minus 40 C to 125 C ambient, and the family document also mentions functional safety documentation being available for system level work. That documentation is not a certification of the system: it is the input a safety case needs, and a product that claims ASIL compliance on the strength of the part alone has skipped the analysis that the standard actually asks for. The DRV8703-Q1 in the same family adds a serial configuration interface, so the two parts differ in how settings are delivered rather than in what the bridge can do.

Where this order code fits

This order code belongs on automotive body and comfort actuators, pumps, seat and mirror mechanisms, HVAC doors and small traction drives, and on industrial equivalents that need an external FET bridge with calibrated switching behaviour. It is chosen when the bridge has to be built from discrete FETs because the current or the thermal path is beyond an integrated driver, and when the switching edge has to be slowed deliberately to pass an emissions test. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Defense Grade Components page.

Questions buyers ask

Can this driver run from a 48 V bus? The recommended operating range stops at 45 V, so a nominal 48 V bus is outside it. Automotive 12 V and 24 V systems with load dump protection sit inside the range, and a 48 V industrial bus needs a different driver. The distinction matters because a 48 V bus is a nominal figure and the transient above it is what the part has to survive.

How is the gate slew rate chosen? A resistor between the IDRIVE pin and either ground or AVDD selects one of the source and sink current settings. A higher current gives a faster edge, lower switching loss and more radiated energy; a lower current gives a slower edge and a quieter spectrum at the cost of dissipation. The choice is normally made on an emissions test with the real harness, because the spectrum depends on the loop area as much as on the edge rate.

What is the 17 V clamp protecting? The gate source voltage of the external FETs. Without a clamp, a high side gate driven from the bus would see 45 V and exceed the 20 V limit of most N-channel devices. The clamp holds the drive below that limit independent of the bus, which is also why the high side supply is a charge pump rather than a bootstrap that can be pulled up by the switch node.

How much current can the charge pump supply for a 100 percent duty hold? Twelve milliamps at 13.5 V, ten at 8 V and eight at 5.5 V. That is the budget for the high side gate leakage plus the gate charge at the switching frequency. A hold at 100 percent duty draws only leakage, while a 100 kHz drive from a 5.5 V rail draws gate charge times frequency and can exhaust the pump. Both cases have to be checked against the FET that was chosen.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.