DRV8316CTRGFR
Product Specifications
DRV8316CTRGFR
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV8316CTRGFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV8316CTRGFR: six FETs, the gate drive and the current sense in one 40-pin VQFN
The DRV8316CTRGFR is the hardware configured member of the DRV8316C family, a three-phase motor driver that carries six N-channel power FETs, the gate drive stage, three current sense amplifiers and a small buck regulator on one die. The body is a 7.00 mm by 5.00 mm VQFN with 40 pins on a 0.5 mm pitch and an exposed pad, which is the whole point of the part: a 24 V brushless motor drive that used to need six external FETs, three shunt resistors and a bias supply now fits under a coin.
The operating window is 4.5 V to 35 V, with 40 V as the absolute maximum. One high-side FET plus one low-side FET measure 95 mΩ together at 25 C, so at 8 A peak the conduction loss in the bridge is around 6 W for the pair that is on, split across the two devices. That number is what decides the board area under the pad, not the headline current. A 1.5 µA sleep current at 24 V is the other half of the story, because a battery tool that sits in a drawer for a month cannot afford a driver that drains it.
Current is sensed inside the part, so the three low-side shunts and their amplifiers disappear from the bill of materials. Four gain settings are selected on the GAIN pin, and the sense outputs go straight to the controller ADC. The PWM interface accepts 6x or 3x patterns, which covers sensored and sensorless field oriented control as well as trapezoidal drive, and the input stage works with 1.8 V, 3.3 V and 5.0 V logic without a level shifter.
Two supplies come built in. A buck regulator delivers 3.3 V or 5.0 V at up to 200 mA from the motor rail, with 4.0 V and 5.7 V also available as headroom for an external low dropout regulator, and a 3.3 V linear regulator on AVDD sources 30 mA for analog references. On many drives that removes the separate housekeeping converter and its inductor entirely, which is why the part turns up in handheld tools, gimbal joints and pump controllers where the board is small and the rail is dirty.
Key data for the DRV8316CTRGFR
| Operating range | 4.5 V to 35 V, 40 V absolute maximum on VM |
| Output stage | Three half bridges, integrated N-channel FETs, 95 mOhm combined high side and low side at 25 C |
| Peak current | 8 A peak, held only inside the thermal budget of the pad and the copper under it |
| PWM | 6x and 3x patterns, switching up to 200 kHz |
| Current sense | Built in, no external shunt, four gain settings on the GAIN pin |
| Buck regulator | 3.3 V, 4.0 V, 5.0 V or 5.7 V at up to 200 mA, 47 uH or 22 uH inductor |
| Linear regulator | 3.3 V at 30 mA on AVDD for analog and reference loads |
| Overcurrent | 16 A or 24 A trip point selected on the OCP/SR pin, plus a cycle by cycle limit option |
| Logic | 1.8 V, 3.3 V and 5.0 V CMOS inputs |
| Sleep current | 1.5 uA at 24 V and 25 C |
Body, packing and marking data
| Body | 40-pin VQFN, the RGF outline, 7.00 mm by 5.00 mm, 1 mm maximum height, 0.5 mm pitch |
| Carrier | 3000 pieces on a 330 mm large tape and reel |
| Finish | NIPDAU lead finish, moisture level 2, 260 C peak reflow, one year floor life |
| Temperature | Minus 40 C to plus 125 C operating, junction range wider |
| Marking | DRV8316CT on the body, lot and date code on the reel label |
Reading the code before you buy it
The string splits four ways. DRV8316C is the circuit generation, T is the hardware interface, RGF is the 40-pin VQFN body, and the final R is the large tape and reel. Swap the T for an R and the order code becomes DRV8316CRRGFR, which is the same silicon with a 5 MHz 16-bit SPI port in place of the configuration pins. The two parts are not interchangeable on a board that has already been laid out, because the pin function on several pads changes, so a purchasing substitution across the T and R suffixes has to be checked against the drawing rather than against the data sheet text.
The nFAULT pin needs attention on the board level. The vendor asks for a pull-up even when the fault output is not used, and the note adds that if an external supply pulls the pin up it has to reach more than 2.2 V at power-up, otherwise the device can enter an internal test mode and behave in a way that has nothing to do with the motor. A board that ties nFAULT to a 1.8 V rail through a weak resistor has a startup race that shows up as a dead driver on a small percentage of units.
The buck pins are the second trap. If the buck is not used, SW_BK, GND_BK and FB_BK cannot be left floating and cannot be tied to ground: the inductor and the feedback divider still have to be fitted. That is a bill of materials that buyers sometimes try to strip out of a cost down, and it is the reason a stripped board comes back as a non-starter.
Where the DRV8316CTRGFR earns its space
CPAP blowers and small fan modules are the classic case, because the motor is a three-phase brushless unit running from 24 V and the housing has no room for six FETs. Camera gimbal joints follow the same shape with a lower current, and the 200 kHz switching ceiling keeps the ripple inside the small inductors those products use.
HVAC blowers run the part close to its thermal edge. A 24 V, 80 W motor draws a little over 3 A continuous, and at 95 mOhm the bridge drops about 0.3 V per phase, which is 1 W of heat per phase inside the package. The exposed pad has to reach a copper area that can carry that away at 85 C ambient, and the peak current has to stay inside the 16 A trip point during a start.
Robotics joints and battery tools use the integrated buck to power the controller from the same 24 V rail, which is where the 200 mA ceiling matters: a radio module and a microcontroller fit, a second motor driver does not. A buyer comparing this part against a discrete bridge usually ends up comparing the number of parts on the board, and our drone and UAV component page lists the adjacent parts that show up in the same flight controller and gimbal builds.
Questions we get on this code
Why does the data sheet say 8 A peak when the part is used at 3 A? Because peak is the current the bridge can pass for the length of a start or a stall before the overcurrent comparator acts, and continuous current is set by junction temperature. A 3 A continuous drive at 24 V sits comfortably, a 3 A drive at 35 V with a slow fan does not.
Can the buck run the microcontroller and the LDO run the analog reference at the same time? Yes, and that is the intended split: 5.0 V at 200 mA from the buck for the MCU and the gate drivers of a second stage, 3.3 V at 30 mA from AVDD for a reference. The two are independent, so a short on the buck output does not take the analog rail down.
Do I still need external shunts? No. The sense elements are inside the part and the gain is set by pin. What is lost is the ability to choose the shunt value, so a board that needs a very wide dynamic range has to check the four available gains against the ADC window before committing.
What happens at 36 V? The operating maximum is 35 V and the absolute maximum is 40 V, so a nominal 36 V rail is outside the operating window even before any transient. A 36 V system needs a part rated above it, and the cross reference route for that class of swap is on our pin to pin cross reference page.
Is the T suffix available on a small reel? The published addendum lists 3000 pieces on a large reel only, so a prototype build either buys a full reel or takes parts from a broken reel. That is worth knowing before a twenty piece pilot is planned.