Contact Us

DRV8313RHHR

Brand: Texas Instruments
Texas Instruments DRV8313RHHR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV8313RHHR — Power Management & Signal Chain | Superb Automation

DRV8313RHHR

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV8313RHHR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV8313RHHR: A Triple Half Bridge in a 6 mm QFN With an Uncommitted Comparator

DRV8313RHHR is a three channel half bridge driver for brushless, solenoid and brushed loads in a VQFN (RHH) body of 36 pins. Each of the three bridges is controlled on its own enable and input pin, carries 2.5 A peak from 8 V to 60 V, and has a separate ground return so a shunt can be placed under any one of them. The part also contains a 3.3 V 10 mA regulator for the controller and a comparator with a 7 mV offset window that can be wired into a current limit without any external amplifier.

Order code and package

Ordering stringDRV8313RHHR, large reel, 2500 pieces
Family documentDRV8313, SLVSBA5D, revised April 2016
PackageVQFN (RHH), 36 pins, 6.00 mm by 6.00 mm
Lead finishNIPDAU
Moisture levelLevel 3, 260 C, 168 hour floor life
Body markingDRV8313
Temperature rangeminus 40 to plus 125 degrees
Tube row in the same bodyDRV8313RHH, 60 pieces in a tube
HTSSOP alternativeDRV8313PWPR, 28 pins, 2000 pieces, same die
Rows that differ only by suffixDRV8313RHHR.A, DRV8313RHHR.B, DRV8313RHHRG4

Electrical parameters that decide the application

Supply range8 to 60 V, absolute maximum 65 V
Supply ramp limit2 V per microsecond
Peak output current per bridge2.5 A, internally limited
FET resistance0.24 Ohm at 25 C, 0.29 Ohm typical and 0.39 Ohm maximum at 85 C
Charge pump headroomVCP to VM 12 V maximum in absolute terms
Internal regulator3.3 V, 3.1 to 3.52 V window, 10 mA maximum
Comparator offsetplus or minus 7 mV
Comparator response2 us for a 100 mV step with 10 mV of overdrive
Logic thresholds0.6 to 0.7 V low, 2.2 V high, 50 to 600 mV of hysteresis
Overcurrent trip3 to 5 A per bridge, 5 us of deglitch
Undervoltage lockout6.3 to 8 V rising
Switching delays300 to 500 ns from input to output, 130 to 475 ns through the enable pin
Output dead time90 ns
Thermal shutdown150 to 180 C with 35 C of hysteresis

Family variants and how they differ

DRV8313 in HTSSOPSame die in a 28 pin body, 9.70 mm by 4.40 mm, poorer thermal path
DRV8313 in VQFN36 pins, 6 mm square, the body on this page
ChannelsThree independent half bridges, not a three phase state machine
Ground returnsOne per bridge, so a single shunt can be placed on any leg
ComparatorUncommitted, with both inputs and the output brought out
Regulator3.3 V at 10 mA, enough for a small controller or a sensor
What is missingNo charge pump fault latch and no SPI, both arrive in later families

Points to check before this part goes on a BOM

This is three half bridges, not a motor controller. Every output follows its own input pin while the enable pin is high, so the commutation table lives in the controller and the part simply amplifies it. That is an advantage when the load is a solenoid pair or a brushed motor and a disadvantage when the controller has no spare timer, because the dead time between the high and low side of one bridge is only the 90 ns inserted internally and any overlap in the firmware table becomes a shoot through.

The separate ground returns are the feature that earns this part its place on a current sensing board. Each bridge has its own PGND pin, so a shunt under one leg measures that leg alone, and the internal comparator can compare the amplified voltage with a reference and feed the result back into the enable pin to build a cycle by cycle limit with three components. The 7 mV offset window is tight enough for a 10 mOhm shunt at 2 A, where the signal is 20 mV.

The 3.3 V regulator is a convenience with a limit. It holds 3.1 to 3.52 V up to 10 mA from a supply above 8 V, which runs a small microcontroller in a fan or a gimbal. It does not survive a short on its output and it is not protected against back feeding, so a board that also has a 3.3 V rail from elsewhere has to keep the two apart with a diode or leave the internal regulator unloaded.

Level 3 moisture sensitivity is the practical difference between the two packages. The QFN body has a 168 hour floor life after the bag is opened, which is three working weeks of single shift assembly, and a board that sits on a bench longer than that needs a bake before reflow. The HTSSOP body carries the same Level 3 rating, so the choice between them is thermal and mechanical, not logistical.

Where a 60 V triple half bridge is the right size

A camera gimbal, an HVAC damper motor and a hospital bed actuator all run from 24 V and draw under 1.5 A, but they need three phases or two directions plus a brake, and they need the controller to decide the sequence. The 8 V floor of this part rules out a single cell lithium pack, and the 60 V ceiling covers a 48 V industrial rail with margin for regen, which is the window where the part earns its cost against a discrete bridge of six FETs and a driver.

A solenoid driver uses the same three channels differently. Two bridges pull a latching solenoid in each direction and the third drives a holding coil, with the comparator watching the current in the holding coil and the enable pin as the actuator. That arrangement avoids a separate solenoid driver and uses a part that was intended for a motor, which is legitimate as long as the inductive kick is clamped at the outputs and the 65 V absolute maximum is respected.

A sixty volt rail is also a sixty volt fault. A motor that is braking returns current to the supply, and a supply with no path for that current lifts the rail until something clamps it. The 65 V absolute maximum on VM and the 12 V headroom of the charge pump set the ceiling, so the board needs a bulk capacitor that absorbs the regen of the load and, on a 48 V rail, a clamp that turns the energy into heat before the bridge sees it. The part turns its outputs off above the lockout rather than trying to ride through, so the mechanism coasts and the controller sees a fault rather than a destroyed bridge.

Where this order code fits

Boards moving from a discrete six FET bridge usually compare the integrated options on the cross reference page first Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Obsolete Part Cross Reference Hub page.

Questions buyers ask

Is 2.5 A a continuous rating? It is the peak the bridge will deliver before the 3 to 5 A overcurrent trips. Continuous current is set by the 0.29 to 0.39 Ohm pair and the thermal path, which in the 6 mm QFN with a soldered pad is roughly 1 A per bridge at 25 C ambient and less inside an enclosure.

Can two bridges be paralleled for more current? They can be driven from the same input pins, but the two dies inside the package do not share current evenly and there is no current balancing circuit. The vendor does not publish a paralleled rating, so a 4 A load needs a different part rather than two channels tied together.

Does the part need an external charge pump capacitor? Yes. VCP, CPH, CPL and CPP are all brought out, and the flying and storage capacitors have to be fitted for the high side gate drive to work. Without them the high side FETs never enhance and the bridge appears to work only on the low side.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.