DRV8302DCAR
Product Specifications
DRV8302DCAR
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV8302DCAR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV8302DCAR: Three Half Bridges, Two Shunt Amplifiers and a 1.5 A Buck in One 56 Pin Body
DRV8302DCAR is a three phase gate driver with dual current shunt amplifiers and an integrated buck regulator in a HTSSOP (DCA) body of 56 pins. It drives six N channel MOSFETs from a single rail anywhere between 8 V and 60 V, sources 1.7 A and sinks 2.3 A into each gate, and carries a bootstrap circuit with a trickle charge path so a high side FET can stay on at 100 per cent duty. Two shunt amplifiers with a pin selected gain of 10 or 40 V/V sit beside a 570 kHz buck that delivers up to 1.5 A for the controller, so a motor drive needs one chip and a handful of passives instead of three.
Order code and package
| Ordering string | DRV8302DCAR |
| Family document | DRV8302, SLES267C, revised March 2016 |
| Package | HTSSOP (DCA), 56 pins, 14.00 mm by 6.10 mm with a thermal pad |
| Reel and packing | 2000 pieces on a large reel |
| Lead finish and moisture | NIPDAU, level 3 at 260 C, 168 hour floor life |
| Temperature range | minus 40 to plus 125 degrees |
| Body marking | DRV8302 |
| Tube option | DRV8302DCA, 35 pieces in a tube |
| Control interface | Hardware pins only, no serial port |
| Dead time setting | One resistor from DTC to ground, 0 to 150 kOhm for 50 to 500 ns |
| Current limit setting | A voltage on OC_ADJ sets the VDS trip point of the external FETs |
| PWM input modes | Six input or three input, chosen by the PWM mode pin |
Electrical parameters that decide the application
| Supply range | 8 to 60 V on PVDD, with a UVLO that drops the part below about 6 V |
| Peak source current | 1.7 A into the gate |
| Peak sink current | 2.3 A out of the gate |
| Gate drive rail | GVDD regulated internally, with an overvoltage lockout above it |
| Dead time | 50 ns with DTC grounded to 500 ns with 150 kOhm, minimum 45 ns after handshake |
| Shunt amplifier gain | 10 V/V with the GAIN pin low, 40 V/V with it high |
| Shunt amplifier offset | Adjustable up to 3 V for bidirectional current sensing |
| Buck output current | Up to 1.5 A, with an adjustable output and switching frequency |
| Buck example in the document | 3.3 V at 570 kHz from a 3.5 to 40 V input |
| Logic interface | 3.3 V and 5 V compatible inputs |
| Current sense method | VDS sensing of the external high side and low side FETs |
| Fault reporting | nFAULT for a latched fault and nOCTW for overcurrent and overtemperature warning |
Family variants and how they differ
| DRV8302 | This part, with the buck and two shunt amplifiers in the 56 pin body |
| DRV8303 | The same gate driver with a serial port in place of the hardware pins, no buck |
| DRV8301 | A predecessor with a similar block set, in the same body, documented separately |
| DRV8323 | The current generation smart gate driver with adjustable drive strength and three shunts |
| DRV8353 | A later family with a higher voltage charge pump and an integrated buck option |
| DRV8300 | A gate driver only, no amplifiers and no buck, for a smaller board |
Points to check before this part goes on a BOM
Dead time is set by one resistor and the number is a compromise. With the pin grounded the part inserts 50 ns, which is right for a fast FET with a small gate charge and wrong for a large module where the real switching edge is longer than that, and body diode conduction during the window costs efficiency. At 150 kOhm the window is 500 ns, and the vendor counts 45 ns as the minimum after the handshake logic has done its work.
The buck is not a separate convenience, it is what makes a single rail board possible. It runs from the same PVDD, needs an inductor, a diode and a feedback divider, and gives up to 1.5 A at a switching frequency set by a resistor. The document quotes 3.3 V at 570 kHz from a 3.5 to 40 V input, which is the rail a 3.3 V controller wants, and the feedback pin is the place to check first if the controller resets when the motor starts.
The two shunt amplifiers have a fixed gain pair, 10 or 40 V/V, and their offset can be shifted up to 3 V so a bidirectional current swing stays inside a single ended ADC window. The gain choice is a pin, not a register, so the board has to decide before it is built. At 40 V/V a 1 mOhm shunt gives 40 mV per amp, which is comfortable for a 20 A drive and too coarse for a 1 A one.
The protection that matters is the VDS sensing, because it protects the external FETs and not the chip. The trip point is set by a voltage on OC_ADJ, the part compares the drain to source voltage across the conducting device, and the response is a latched shutdown reported on nFAULT. A FET with a higher RDS(on) at temperature trips earlier at the same setting, so the resistor divider has to be trimmed for the hot resistance and not the 25 C one.
Thermal warning comes before thermal shutdown, and the two are reported on different pins. nOCTW goes low at the warning level, which lets a controller reduce current or raise fan speed, while the shutdown level turns the gate driver and the charge pump off and latches until the part is cycled. Reading nOCTW and doing nothing is the same as waiting for a thermal shutdown with a motor still spinning.
Where a three phase driver with a buck is the right shape
A pump, a fan or a small compressor with a 24 V or 48 V rail and a 3.3 V controller is the natural fit. The buck makes the 3.3 V from the same rail, the two shunt amplifiers measure the current in the two low side legs that are already there, and the gate driver runs the six FETs from the rail with a bootstrap that tolerates a static high side command.
The 60 V ceiling puts it on a 48 V bus with margin for the regen spike, and the 8 V floor keeps it out of single cell battery work. A 12 V automotive rail with load dump needs a clamp in front, because the absolute maximum is well below the transient, and the buck input divider has to be checked at the highest rail the load dump clamp allows.
What has to be checked on a replacement
The body is the first thing, because 56 pins in an HTSSOP with a thermal pad is not the same footprint as the later 40 pin QFN parts that share the family name. The pin names match, the functions match, and the package does not, so a cross reference that stops at the part number is wrong.
The second is the current sense arrangement. This part measures the FET drop, so the resolution falls with current and the reading is useless below a tenth of the rated current. A board that needs an accurate reading at light load needs a shunt and an amplifier, which is the reason the later families added three dedicated shunt amplifiers.
Where this order code fits
The part fits a 24 V to 48 V three phase drive that needs its own 3.3 V rail and two current readings, in a body large enough to solder by hand for a first build. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
Can this part run a motor at 100 per cent duty? Yes, the bootstrap has a trickle charge path for it, which is the difference between this part and a plain bootstrap driver that drops the high side gate after a few milliseconds of static on time.
Is the buck powerful enough for the controller? It delivers up to 1.5 A, which covers a 3.3 V MCU, its memory and a small display. A radio or an SD card that draws pulses needs a separate regulator, because the buck is inside the same thermal package as the gate driver.
What sets the overcurrent trip point? A voltage on OC_ADJ, compared against the VDS of the conducting FET. It is a threshold on the FET drop, so the equivalent current moves with temperature and has to be set from the hot RDS(on).
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Obsolete Part Cross Reference Hub page sets out the checks that keep a substitute from failing on the bench.