Contact Us

DRV8300NRGER

Brand: Texas Instruments
Texas Instruments DRV8300NRGER is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV8300NRGER — Power Management & Signal Chain | Superb Automation

DRV8300NRGER

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV8300NRGER from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV8300NRGER: A 100 V Three Phase Gate Driver That Leaves the Bootstrap Diode to the Board

DRV8300NRGER is a three phase half bridge gate driver for external N channel MOSFETs in a VQFN (RGE) body of 24 pins. It drives six N channel FETs from a gate supply of 5 V to 20 V while the phase pins tolerate 85 V in normal operation and 110 V in absolute terms, which is what makes a 15 cell battery stack practical without an isolated gate supply. The N in the string means the bootstrap diode is external, the DI and D variants carry it inside, and the QFN body adds a DT pin that sets dead time with one resistor.

Order code and package

Ordering stringDRV8300NRGER, large reel, 3000 pieces
Family documentDRV8300, SLVSFG5D, revised March 2022
PackageVQFN (RGE), 24 pins, 4.00 mm by 4.00 mm, exposed pad
Lead finishNIPDAU
Moisture levelLevel 1, 260 C, unlimited floor life
Body marking8300N
Temperature rangeminus 40 to plus 125 degrees ambient, 150 degrees junction
Sibling rows in the same bodyDRV8300DRGER with the diode inside, same reel and marking 8300D
TSSOP siblingsDRV8300DPWR, DRV8300NIPWR, DRV8300DIPWR, all 20 pins on 3000 piece reels
Rows that differ only by suffixDRV8300NRGER.A and DRV8300NIPWRG4, both active

Electrical parameters that decide the application

Gate supply rangeGVDD 5 to 20 V, absolute maximum 21.5 V
Phase pin rangeSHx minus 2 to 85 V recommended, 110 V absolute
Bootstrap pinBSTx to SHx 5 to 20 V recommended, 125 V absolute on BSTx
Source current750 mA typical, 400 to 1200 mA window
Sink current1.5 A typical, 850 to 2100 mA window
Propagation delay125 ns typical, 70 to 180 ns window
Delay matchingplus or minus 4 ns typical, 30 ns limit
Dead time with DT floating215 ns typical, 150 to 280 ns window
Dead time with 400 kOhm to ground2 us typical, 1.5 to 2.6 us window
Minimum input pulse70 ns typical, 150 ns maximum
Gate supply current825 uA typical at 20 kHz switching, no FETs connected
Phase pin leakage55 uA typical, 80 uA maximum
Logic thresholds0.8 V low, 2.0 V high, 100 mV of hysteresis
PWM frequencyup to 200 kHz
Junction to ambient97.4 C per W in TSSOP, 49.3 C per W in the QFN

Family variants and how they differ

DRV8300DBootstrap diode inside, non inverting low side input, fixed dead time, TSSOP
DRV8300DIBootstrap diode inside, inverting low side input, fixed dead time, TSSOP
DRV8300NExternal bootstrap diode, non inverting, fixed dead time in TSSOP
DRV8300NIExternal bootstrap diode, inverting low side input, fixed dead time, TSSOP
DRV8300N in QFNExternal diode, non inverting or inverted selected by the MODE pin
DRV8300D in QFNInternal diode, polarity selected by MODE, variable dead time on DT
Why pick N over DAn external diode allows a higher voltage or a faster part to be chosen

Points to check before this part goes on a BOM

The N suffix is not a trim level, it is a circuit difference. With the diode inside, the bootstrap capacitor is charged through a diode that is rated for the gate supply and nothing more, and the vendor limits the phase slew rate accordingly. With the diode external, the board chooses a diode rated for the full phase voltage, which is the route taken when the phase node swings 85 V and the bootstrap capacitor has to be refilled in a few hundred nanoseconds.

Dead time is the parameter that decides whether this part works on a given bridge. In the TSSOP bodies it is fixed at 215 ns typical, which is long enough to matter at 20 kHz and short enough to be invisible at 5 kHz. In the QFN bodies the DT pin sets it with a resistor, from 200 ns with 40 kOhm to 2 us with 400 kOhm, and with the pin floating the part inserts its default. A bridge with 400 nC of gate charge and a 10 ns switching edge can use the short setting, while a slow FET that turns off in 200 ns needs the long one to avoid a shoot through.

Propagation delay and matching are what the current sense loop cares about. The 125 ns typical delay with plus or minus 4 ns of matching between phases means a low side shunt sees the current of the phase that is actually on, not a mixture of two, and the sampling window at the bottom of a PWM cycle can be short. At 20 kHz the period is 50 us, so a 215 ns dead time plus a few hundred nanoseconds of settling leaves most of the low side on time available, but at 100 kHz the same numbers eat a whole tenth of the period.

The QFN body is 4 mm square with an exposed pad, which is the only reason the thermal figure drops from 97.4 to 49.3 C per W. Gate drive loss at 20 kHz with 100 nC of gate charge and 12 V of drive is about 24 mW per FET, so six FETs produce 144 mW and the package rise is small either way. The pad still has to be soldered to a plane, because the same pad is the ground return for the low side drivers and a floating pad turns every switching edge into a common mode step on the gate loop.

What a 15 cell stack does to the gate supply

A 48 V nominal pack reaches 63 V on charge and higher on regen, so the phase pins have to sit at 85 V with margin, and the gate supply has to be generated from the same rail or from a separate 12 V housekeeping supply. GVDD at 12 V keeps the FET fully enhanced, and the undervoltage lockout at 4.6 V rising and 4.35 V falling on the gate supply is what stops the bridge from running a FET in its linear region after a brownout.

The bootstrap capacitor has to be sized from the gate charge and the leakage, not copied from another board. The phase pin leaks 55 uA typical and the bootstrap pin 4 uA, and the capacitor has to hold the gate above the 4.2 V undervoltage limit for the longest high side on time in the application. At 100% duty the high side never turns off, and there is no refresh, so a bridge that needs continuous conduction has to use the trickle charge path of the smart gate driver family instead of this part.

Where this order code fits

Most teams arrive here from the gate driver column of the power management cross reference, and swap candidates on the pin to pin table Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Can GVDD be tied to the battery? No. The gate supply has a 21.5 V absolute maximum and a 20 V recommended ceiling, so a 48 V or 60 V rail destroys the part. It needs a 12 V housekeeping supply or a regulator from the pack, and the current drawn is under 1 mA when no FETs are connected.

What happens if the DT resistor is left off? In the QFN body the pin floats and the part inserts its default dead time, which is the same 215 ns as the TSSOP bodies. A resistor to ground from 40 kOhm upward lengthens it, and the vendor table stops at 400 kOhm for 2 us.

Does the external diode version need a different capacitor? It needs a capacitor rated for the phase voltage rather than for the gate supply, because the whole bootstrap node moves with the phase. A 100 V X7R part in the same value is the usual substitution, and the diode has to be a fast recovery type rated above the pack voltage.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.