Contact Us

DRV8262DDWR

Brand: Texas Instruments
Texas Instruments DRV8262DDWR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV8262DDWR — Power Management & Signal Chain | Superb Automation

DRV8262DDWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV8262DDWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV8262DDWR: Two 60 V H Bridges With Current Sense on the High Side FETs

DRV8262DDWR is a dual H bridge motor driver with integrated current sensing in a HTSSOP (DDW) body of 44 pins. It works from 4.5 V to 60 V and carries two H bridges that can drive two brushed motors, one stepper or two thermoelectric coolers, with 8 A peak per bridge in this package and 16 A when both halves are paralleled into one bridge. Current is mirrored out of the high side FETs at 212 uA per amp, so no shunt is needed, and the chopping off time is selectable between 7 us and 32 us.

Order code and package

Ordering stringDRV8262DDWR
Family documentDRV8262, SLVSFV5C, revised July 2025
PackageHTSSOP (DDW), 44 pins, 14 mm by 6.1 mm, thermal pad on the bottom
Reel and packing2500 pieces on a large reel, NiPdAu lead finish
Moisture levelLevel 3, 260 C peak, 168 hours of floor life
Body markingDRV8262
Temperature rangeminus 40 to plus 125 degrees
Top pad siblingDRV8262DDVR, the same die with the thermal pad on the top, same reel size
Interface optionsPH/EN or PWM, selected by the MODE pins
Current senseIPROPI output per bridge, 212 uA per amp
Fault handlingOCPM pin selects latch off or automatic retry
Decay and off timeDECAY pin is tri level, TOFF pin is quad level

Electrical parameters that decide the application

Supply range4.5 to 60 V
Bridge resistance, dual50 mΩ typical and 60 mΩ maximum per FET at 25 C, 100 mΩ for the pair
Bridge resistance, single25 mΩ typical and 30 mΩ maximum per FET at 25 C, 50 mΩ for the pair
Peak current, this package8 A per bridge in dual mode, 16 A in single bridge mode
Peak current, top pad package16 A per bridge in dual mode, 32 A in single bridge mode
Overcurrent trip, this package8 A per bridge in dual mode, 16 A in single bridge mode
Current mirror gain212 uA per amp
Mirror accuracy12 per cent at 10 to 20 per cent of rated current, 7 per cent at 20 to 40 per cent, 4 per cent at full current
Sleep current3 uA typical and 8 uA maximum
Internal logic rail5 V plus or minus 5 per cent on DVDD
Undervoltage2.9 V typical rising, 3.05 V typical maximum, 100 mV of hysteresis
Charge pumpVM plus 5 V, 360 kHz switching
Thermal shutdown165 C typical with 150 C and 180 C limits, 20 C of hysteresis
Overcurrent timing2.1 us of detection delay and 4.1 ms before a retry

Family variants and how they differ

Off time 7 usTOFF pin at ground, the fastest chopping and the lowest current ripple per cycle
Off time 16 usTOFF pin at DVDD, a middle setting for medium inductance motors
Off time 24 usTOFF pin left floating, the usual choice for a stepper winding
Off time 32 usTOFF pin through 330 kΩ to ground, for high inductance loads
Slow decayDECAY at ground, both high side FETs on during the off time
Smart tuneDECAY at DVDD, the vendor adaptive decay setting for stepper current waveforms
Mixed decayDECAY floating, 30 per cent fast decay followed by slow decay
Latch offOCPM low, the bridge stays off until an nSLEEP reset pulse or a power cycle
Automatic retryOCPM high, the bridge resumes once the junction temperature falls by the hysteresis

Points to check before this part goes on a BOM

The peak current is a package number, not a die number. Both order codes carry the same silicon, and the difference between 8 A and 16 A per bridge is whether the thermal pad faces the board or the air. A team that specifies the DDW part for a 12 A stall and then reads the DDV column of the same document will believe the part can do twice what the mounted package can actually hold, and the overcurrent trip in this body is set at 8 A for the same reason.

Current sense accuracy is stated in bands, and the band matters at the threshold an engineer actually uses. The mirror is within 4 per cent at full rated current, but only 12 per cent between 10 and 20 per cent of rating, so a stall detector set at 15 per cent of rating inherits the wider figure. Below 10 per cent the part publishes no accuracy at all, and the mirror only reports current that flows through the high side FETs, so no reading is available in coast or in slow decay with the low side conducting.

The current regulation loop compares the voltage on IPROPI with VREF, which means the trip point is set by two passive parts. The vendor example puts 3.3 V on VREF with 3.09 kΩ on IPROPI to reach 5 A, and a one per cent resistor moves the trip by one per cent while a change in the mirror gain moves it by more. The loop chops with the selected off time and allows a double off time when the current has not fallen below the threshold, which is what keeps a stalled motor from sitting at the limit continuously.

The way the part comes back from a fault depends on a pin that is often tied to a fixed level early in the programme. With OCPM low the bridge latches off after an overcurrent or an overtemperature event and needs an nSLEEP reset pulse of about 120 us, or a power cycle, before it will drive again. With OCPM high it retries on its own after 4.1 ms, which is friendlier for a mechanism that jams and clears but harder on a bridge that is shorted.

The 60 V rating covers the supply, not the energy that comes back from the motor. A 48 V rail with a spinning load can push the bridge node above the rail during braking, and the charge pump and the absolute maximum ratings have to be checked against that overshoot rather than against the nominal supply. The same applies to a supply that is switched on through a long cable, where the inductance produces a spike well above the steady value.

Single bridge mode and what it costs

Tying the two bridges in parallel halves the resistance to 50 mΩ for the pair and doubles the current to 16 A in this package, which is how a single large brushed motor or a thermoelectric cooler is driven. The parallel connection is not just a wiring choice: the two halves have to be driven with the same inputs, and the current mirror then reports the sum, so the trip point set on VREF applies to the combined current rather than to one half.

The thermal path also changes, because the dissipation is now concentrated in one logical bridge even though it is spread across the same silicon. A cooler driven at 12 A continuously at 24 V drops about 7.2 W in the bridge at 50 mΩ, which the 44 pin body can only hold with a copper area on the pad and some airflow. The thermal shutdown at 165 C is a last resort, not a working point.

Chopping a stepper winding

A bipolar stepper needs a current waveform, not a voltage, and the off time setting decides how closely the waveform follows the reference. The 7 us setting gives the smallest ripple but the highest switching loss, and the 32 us setting is for windings with enough inductance that the current cannot rise far in a short window. The decay mode is the second half of the choice: mixed decay at 30 per cent fast keeps the current from climbing at each step, while slow decay is quieter and simpler.

Both bridges are needed for one stepper, so the peak current per phase is half of what a single bridge could deliver. That is the trade a stepper application makes with this part, and it is the reason the single bridge mode exists for the case where one large load matters more than two small ones.

Where this order code fits

The part fits a 24 V or 48 V mechanism with one or two brushed motors, a stepper or a thermoelectric cooler, where the current has to be limited and reported without a shunt resistor on the board. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Can this package really deliver 16 A? Only when both bridges are paralleled into one, and only with the thermal pad soldered to a copper area that can carry the heat. In dual bridge mode the same body is limited to 8 A per bridge and the overcurrent trip is set to match.

Does the current sense work in both directions? It mirrors current through the high side FETs only. Forward and reverse drive are both reported, because the high side FET of the conducting half carries the current in either direction, but coast and low side recirculation are not, so a reading has to be taken while the bridge is actually driving.

What is needed to clear a latched fault? With OCPM tied low, a low pulse on nSLEEP of about 120 us, or a power cycle. With OCPM high the part retries by itself after roughly 4.1 ms. The choice is made on the board, not in firmware.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.