DRV8251DDAR
Product Specifications
DRV8251DDAR
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV8251DDAR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV8251DDAR: A 4.1 A Brushed Motor Driver That Latches Off on a Fault Instead of Retrying
DRV8251DDAR is a single H bridge brushed DC motor driver with analogue current regulation in a SO PowerPAD (DDA) body of 8 pins. It runs from 4.5 V to 48 V, switches at up to 200 kHz from 1.8 V, 3.3 V or 5 V logic, and limits motor current by comparing a reference voltage with the drop across a shunt resistor on the ISEN pin. The two FETs measure 225 mOhm each, and the overcurrent response on this member is a latch rather than an automatic retry, which is the single difference that decides whether a jammed mechanism recovers by itself or waits for the controller to reset it.
Order code and package
| Ordering string | DRV8251DDAR, large reel, 3000 pieces |
| Family document | DRV8251, SLVSFZ6, December 2021, first release |
| Package | SO PowerPAD (DDA), 8 pins, 4.90 mm by 6.00 mm |
| Lead finish | NIPDAU |
| Moisture level | Level 2, 260 C, one year floor life |
| Body marking | DRV8251 |
| Ambient range on the addendum | minus 40 to plus 125 degrees |
| Junction range in the electrical table | minus 40 to plus 150 degrees |
| Second row of the same string | DRV8251DDAR.A, same body, same reel, same marking |
| Pins that matter on a board | VM, OUT1, OUT2, ISEN, VREF, IN1, IN2, GND plus the pad |
Electrical parameters that decide the application
| Supply range | 4.5 to 48 V, absolute maximum 50 V |
| Supply ramp limit | 2 V per microsecond on VM |
| Peak output current below 5.5 V | 3.7 A |
| Peak output current at 5.5 V and above | 4.1 A |
| FET resistance, high side and low side | 225 mOhm each at 24 V and 1 A |
| Sleep current | 1 uA at 24 V and 25 C when both inputs are low |
| Active supply current | 3 mA typical, 4 mA maximum, no load |
| Wake and sleep timing | 250 us to wake, 0.8 to 1.5 ms to enter sleep |
| Input to output delay | 0.7 to 1 us, with 200 ns of dead time inserted |
| ISEN amplifier gain | 10 V per V, window 9.6 to 10.4, with VREF at 2.5 V |
| Current regulation timing | 25 us off time and 2 us of blanking |
| Undervoltage lockout | 4.15 to 4.45 V rising, 4.05 to 4.35 V falling, 100 mV of hysteresis |
| Overcurrent trip point | 3.7 A below 5.5 V, 4.1 A at 5.5 V and above, 0.7 V on ISEN |
| Thermal shutdown | 150 C minimum and 175 C typical, 40 C of hysteresis |
| Junction to ambient | 40.4 C per W in the DDA body |
Family variants and how they differ
| DRV8870 | 6.5 to 45 V, 565 mOhm, external shunt, automatic retry, same footprint |
| DRV8251 | 4.5 to 48 V, 450 mOhm, external shunt, latched disable, the part on this page |
| DRV8231 | 4.5 to 33 V, 600 mOhm, external shunt, automatic retry, HSOP or WSON |
| DRV8251A | 4.5 to 48 V, 450 mOhm, internal current mirror on IPROPI, automatic retry |
| DRV8231A | 4.5 to 33 V, 600 mOhm, current mirror, automatic retry |
| What the letter A changes | The A members report current on a pin instead of needing an amplifier |
| What the latch changes | A fault holds the outputs off until the inputs are cycled |
Points to check before this part goes on a BOM
The latch is the reason to pick this member over the DRV8231. When an overcurrent trip occurs the outputs turn off and stay off, and the device only returns to normal operation after both inputs have been held low long enough for the sleep timer to run and then released for the wake time. On a pump that jams once a month that is exactly the behaviour wanted, because the mechanism does not hammer itself against the obstruction while the controller decides what to do. On a printer carriage that stalls on a paper edge the same behaviour looks like a dead driver to a service engineer, and the firmware has to pulse the inputs to clear it rather than assume the part has failed.
Current regulation is set by two components. The amplifier gain is 10 V per V, so the trip point is the reference voltage divided by ten times the shunt resistance. A 0.2 Ohm shunt with 2.5 V on VREF trips at 1.25 A, and the same shunt with 0.5 V trips at 250 mA. The shunt carries the full motor current, so its rating and its temperature coefficient decide the accuracy of the limit far more than the amplifier does. At 1.25 A a 0.2 Ohm resistor dissipates 313 mW, which rules out an 0603 part and points at a 1206 or a current sense resistor in a wider body.
The 4.1 A figure is a peak rating and the thermal table explains why. Conduction loss is the square of the current times 450 mOhm for the pair of FETs, so 1 A produces 0.45 W and a rise of about 18 C, 2 A produces 1.8 W and a rise of 73 C, and 3 A produces 4.05 W and a rise near 164 C, which is already past the shutdown point before any switching loss is added. A motor that draws 3 A continuously needs a driver with lower resistance or a much larger copper area under the pad, and the peak rating is there for the inrush of a cold winding.
Sleep entry is not instant. Setting both inputs low starts a timer of 0.8 to 1.5 ms before the internal circuits shut down, and the part needs 250 us of a high input before it is fully awake again. A controller that pulses the inputs at a 100 us rate to save power never lets the part settle in either state, and the supply current sits between the 1 uA sleep figure and the 3 mA active figure with no guarantee of which. The pulse rate in the firmware has to be slower than both timers, or the driver should simply be left awake.
What the board has to provide
A 0.1 uF ceramic within a few millimetres of VM, plus bulk capacitance sized for the motor current and rated for the 48 V rail. The charge pump runs from VM, so a supply that droops during a start transient takes the gate drive down with it, and the undervoltage lockout at 4.3 V then turns the bridge off in the middle of the ramp. A 47 uF electrolytic beside the ceramic covers most small brushed motors up to 2 A.
The pad is the thermal path and it is the only one. The DDA body has the pad on the underside and the 40.4 C per W figure assumes it is soldered to a plane with vias, so a footprint that treats the pad as a mechanical anchor and not as copper turns a 1 A load into a thermal problem. Four to nine vias of 0.3 mm under the pad into an inner ground plane is the usual arrangement, and the same plane carries the ISEN return so the sense voltage does not pick up the bridge current.
Where this order code fits
Teams replacing a 565 mOhm driver with this one, or moving a mechanism from 24 V to 48 V, usually start from the cross reference table Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
Can the ISEN pin be tied straight to ground? Yes, when current regulation is not used. The internal amplifier then sees zero volts and the regulation loop never trips, leaving only the fixed overcurrent protection at 3.7 or 4.1 A. The pin still has to be connected, because it is also the high current return for the low side FETs.
Does the part survive a locked rotor at 48 V? The overcurrent protection trips and latches, so the bridge turns off rather than dissipating the stall power, and the junction stays inside the 150 C limit provided the trip happens before the thermal shutdown at 150 C. What the part does not do is retry, so a stalled motor stays stalled until the controller clears the latch.
What separates this from the DRV8251A? The A member replaces the external shunt and amplifier with an internal current mirror brought out on IPROPI, which removes the shunt loss but removes the ability to set the limit with a resistor, and its fault response is an automatic retry rather than a latch.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.