DRV8231DDAR
Product Specifications
DRV8231DDAR
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV8231DDAR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV8231DDAR: 3.7 A brushed DC motor driver with a 33 V rating and a 600 milliohm bridge
DRV8231DDAR is a single H-bridge motor driver in the eight pin DDA body that runs from 4.5 V to 33 V, integrates 600 milliohm of combined switch resistance, delivers 3.7 A peak and regulates current with an external shunt in a HSOP with PowerPAD body of 8 pins. The DRV8231 is the shunt sensing member of the pair that also includes the mirror based DRV8231A. It is an N-channel H-bridge rated 4.5 V to 33 V with 600 milliohm of combined switch resistance and 3.7 A of peak output, controlled over a PWM interface that accepts 1.8 V, 3.3 V and 5 V logic. The body is an eight pin HSOP with a PowerPAD, and sleep current is under 1 uA at 24 V.
Order code and package
| Order code | DRV8231DDAR |
| Function | single H-bridge brushed DC motor driver |
| Operating supply voltage | 4.5 V to 33 V |
| Peak output current | 3.7 A |
| Combined switch resistance | 600 milliohm |
| Current sense | external shunt resistor |
| Logic inputs | 1.8 V, 3.3 V and 5 V compatible |
| Sleep current | under 1 uA at 24 V and 25 C junction |
| Package | eight pin HSOP with PowerPAD, 4.9 mm by 6.0 mm |
| Sibling order code | DRV8231A, same bridge with a current mirror |
Electrical parameters that decide the application
| Family range, DRV8870 | 6.5 V to 45 V, 565 milliohm, shunt based |
| Family range, DRV8251 | 4.5 V to 48 V, 450 milliohm, shunt based |
| Family range, DRV8251A | 4.5 V to 48 V, 450 milliohm, mirror based |
| Family range, DRV8231A | 4.5 V to 33 V, 600 milliohm, mirror based |
| Bridge resistance at 1 A | 0.6 V of drop and 0.6 W of loss |
| Bridge resistance at 2 A | 1.2 V of drop and 2.4 W of loss |
| Bridge resistance at the 3.7 A peak | 2.2 V of drop and 8.2 W of loss |
| Junction temperature range | minus 40 C to 150 C |
Points to check before this part goes on a BOM
Six hundred milliohms of combined resistance is the term that decides how much of the rail reaches the motor. At 1 A the bridge drops 0.6 V, at 2 A it drops 1.2 V, and at the 3.7 A peak it drops 2.2 V. On a 12 V rail that is a fifth of the supply at the peak, and the loss that produced it is 8.2 W inside an eight pin package. The peak rating is therefore a short event, and the continuous rating is set by how much heat the PowerPAD can move into the board.
The choice between this part and the mirror version is a measurement decision. A shunt gives a voltage that is proportional to current with the tolerance of the resistor and almost no drift, which is what a torque loop or a precise current limit needs. The mirror removes the shunt loss and the shunt drop but inherits a ratio that moves with temperature and process. At 2 A a 0.1 ohm shunt dissipates 0.4 W and drops 0.2 V, which is worth removing on a battery product and worth keeping on a drive that has to hold torque.
The 33 V ceiling is the line between this part and the 48 V member of the same family. Both are eight pin HSOP devices with the same pin out, so a board can be built for 48 V and populated with either, and a 24 V system with load dump transients is the case where the difference matters. A 24 V rail with a transient to 40 V is inside the 48 V part and outside this one, and the family table is the first thing to read before a bill of materials is frozen.
PWM frequency and current ripple are linked through the motor inductance, and the driver only sets the switching speed. A 12 V motor with 1 mH of inductance driven at 20 kHz has a ripple of about 0.3 A, which the current regulation has to average; at 5 kHz the same motor has 1.2 A of ripple and the peak current limiting trips much earlier than the average suggests. The choice of frequency is therefore a decision about the peak current, not only about audible noise.
The PowerPAD has to be soldered to a copper area with vias, and on an eight pin HSOP the pad is the only meaningful heat path. A 2.4 W loss at 2 A is a junction rise of tens of degrees on a good board and far more on a poor one, and the difference between the two is not visible on the drawing or in a simulation that assumes a heatsink. The pad area, the via count and the copper thickness are the thermal specification.
Sleep current under 1 uA at 24 V is useful for a product that holds a mechanism still, but the wake path matters as much. The internal regulator and the gate drive have to come up before the bridge switches, so a controller that applies PWM in the same cycle as the enable will clip the first pulses. The usual arrangement is to enable, wait for the period the data sheet gives for the internal rails, and then start the PWM at a low duty.
The four bridge states include a brake state in which both low side switches conduct. That is the right way to stop a load quickly: the motor current circulates in the low side switches and the energy is dissipated in the bridge and the winding rather than being returned to the supply. Disabling the bridge instead lets the motor coast, and on a 24 V system with a heavy load the coasting current can push the supply up if there is nowhere for it to go.
Where this order code fits
This order code belongs on 12 V and 24 V brushed motor loads in printers, vending machines, valve actuators, lab equipment, home appliances and automotive body mechanisms that do not need the 48 V rating of the larger part in the family. It is chosen when a shunt based current measurement is preferred because the current has to be regulated precisely, or when an existing board already has the sense resistor and its filter. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.
Questions buyers ask
Why choose this over the 48 V part in the same family? The 33 V part has 600 milliohm of bridge resistance against 450 milliohm on the 48 V part, so the 48 V version is both higher voltage and lower loss. The reason to stay with the 33 V part is cost and availability on a 12 V or 24 V product; the reason to move up is a 24 V rail with transients or a load that needs the lower resistance.
Can the 3.7 A peak be sustained? No. At 3.7 A the bridge dissipates about 8.2 W, which is far beyond what an eight pin package can hold continuously even with a good pad. The peak rating covers acceleration and stall events of short duration. A continuous 1.5 A to 2 A is a realistic ceiling with a properly soldered PowerPAD and copper on both sides.
How is the current regulated? The external shunt produces a voltage that the controller compares against a reference, and the PWM duty is reduced when the measured current exceeds the target. The driver itself only switches; the regulation loop lives in the controller. That is a simpler and more predictable arrangement than an internal mirror, and it requires a sense resistor and a filter that do not drift.
What happens if the motor is back driven? The bridge conducts through its internal body diodes and returns current to the supply, which raises the rail unless something absorbs it. On a 24 V system with a large load a braking event can push the supply above its nominal, and the supply capacitance and any clamp have to be sized for that energy. The brake state, with both low side switches on, keeps the current in the bridge instead.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.