DRV10987SPWPR
Product Specifications
DRV10987SPWPR
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV10987SPWPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV10987SPWPR: A Sensorless Sinusoidal Driver for a 12 V or 24 V Fan With No Position Sensor
DRV10987SPWPR is a three phase sensorless BLDC motor driver in a HTSSOP (PWP) body of 24 pins. It runs a three phase fan or pump from 6.2 V to 28 V with integrated MOSFETs, drives 2 A of continuous winding current with a 3 A peak, and does it without a Hall sensor by measuring the back emf and starting the motor with an initial position detect so the rotor does not kick backwards. The S letter in the order code is one of two firmware images, and the body is the 24 pin HTSSOP with a thermal pad.
Order code and package
| Ordering string | DRV10987SPWPR |
| Family document | DRV10987, SLVSE89C, revised June 2020 |
| Package | HTSSOP (PWP), 24 pins with a thermal pad, 7.80 mm by 6.40 mm |
| Reel and packing | 2000 pieces on a large reel |
| Lead finish and moisture | NIPDAU, level 3 at 260 C, 168 hour floor life |
| Temperature range | minus 40 to plus 125 degrees |
| Body marking | 10987S |
| Sibling body | DRV10987DPWPR, same package, marking 10987D |
| Interface | I2C for registers and EEPROM, a SPEED pin for analogue or PWM demand, FG for tach |
| Current sense | No external shunt resistor |
| Commutation | Sensorless sinusoidal, 180 degree |
| Configuration storage | Internal EEPROM, written through I2C |
Electrical parameters that decide the application
| Motor operation range | 6.2 to 28 V, with the part stopping the drive above 28 V |
| Continuous winding current | 2 A, with a 3 A peak |
| On resistance, high side plus low side | 250 mOhm at 25 degrees in the features list |
| The same number in the electrical table | 400 mOhm at 25 degrees with VCC above 6.5 V and 1 A |
| Undervoltage lockout | 5.8 to 6.2 V rising, 5.6 to 6 V falling, 195 mV typical hysteresis |
| High side overcurrent | 4.25 A typical and 5.5 A maximum |
| Low side overcurrent | 4.25 A typical and 5.5 A maximum |
| Phase slew rate | Selectable, from a few V per us to about 145 V per us |
| Speed demand | Analogue voltage or PWM duty on the SPEED pin |
| Speed feedback | FG output and the I2C registers at the same time |
| Start up | Initial position detect, so the rotor does not spin backwards |
| Protection | Undervoltage, overcurrent, overvoltage and thermal shutdown |
Family variants and how they differ
| DRV10987S | This part, one of the two firmware images in the same body |
| DRV10987D | The other image, same package, different default register set |
| DRV10983 | An earlier member of the family with a lower current rating |
| DRV10983-Q1 | The automotive version, with its own tuning guide |
| DRV11873 | A pin configured sensorless driver for a fixed fan, no I2C |
| DRV8313 | A gate driver style part for a three phase bridge with external FETs |
Points to check before this part goes on a BOM
The on resistance is published twice and the two numbers differ. The features list says 250 mOhm at 25 degrees, and the electrical table gives 400 mOhm at 25 degrees with the supply above 6.5 V and 1 A of load. The second number is the one to use for a thermal calculation, because it comes with a test condition attached, and a 1.6 times difference in dissipation is the difference between a fan that runs cool and one that folds back.
The EEPROM is what makes a sensorless fan work out of the box. Motor parameters, the start up current, the alignment time and the commutation timing are written once through I2C and the part then runs standalone with a PWM on the SPEED pin. A board that leaves the EEPROM at its defaults will start some motors and stall on others, which is the most common complaint about this family.
Starting without a sensor needs a strategy, and the initial position detect is it. The part pulses the windings and measures the response to work out where the rotor is before it commutates, so a fan in a duct does not kick backwards on power up. The alternative, a blind ramp, works on a free rotor and fails on a loaded one, which is why the detect is on by default in the tuning guide.
The speed interface has three inputs for three different products. An analogue voltage on SPEED suits a thermistor network in a fan tray, a PWM duty suits a controller with a spare timer, and the I2C registers suit a product that wants to read the speed back and log it. All three work at the same time, so a controller can drive the fan with PWM and still read the actual speed over I2C.
The 28 V ceiling is a real ceiling and not a suggestion. Above it the part stops driving and protects itself, which is the correct behaviour on a 24 V rail with a regen spike from a spinning fan, but it means the supply has to be clamped below the absolute maximum. A 24 V nominal rail with a 10 per cent tolerance and a brake event reaches the limit, so the clamp and the bulk capacitor are part of the circuit, not optional.
Where a sensorless sinusoidal driver fits
A ceiling fan, a pedestal fan, an air purifier or a drain pump is the target. The motor has three wires and no Hall sensors, the board has to be small and quiet, and the demand comes from a knob, a remote or a humidity sensor as an analogue voltage or a PWM. Sinusoidal commutation is what keeps the audible noise below the airflow noise, which a trapezoidal drive does not.
A condenser fan in a refrigeration unit uses the same part with a different tuning set. The EEPROM holds the ramp and the alignment current for the specific motor, so one board can serve several motor variants if the parameters are written at end of line, which is how a fan maker keeps one PCB across a range.
What has to be checked on a replacement
The firmware image letter matters as much as the body. The S and D strings share a package and a pin out but carry different default registers, so a board tuned for one starts differently on the other. A cross reference that treats them as the same part gives a fan that runs at the wrong speed or fails to start on a cold morning.
The second item is the thermal path. The 24 pin HTSSOP has a pad that has to be soldered to copper, and at 2 A the dissipation is around 1.6 W with the 400 mOhm figure. A board that relies on the pad alone without a copper area runs into thermal foldback, which reads as a fan that slows down after ten minutes rather than as a fault.
Where this order code fits
The part suits a 12 V or 24 V fan or pump with a three wire motor, no Hall sensor, and a demand that arrives as a PWM or an analogue voltage. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
Does it need a shunt resistor? No, the current is measured internally and no external sense element is used. The overcurrent protection is a fixed window of about 4.25 to 5.5 A on either side of the bridge.
Can I run it without writing the EEPROM? It will run, but the start up and commutation parameters are generic and some motors stall. The vendor provides a tuning guide and the parameters are written once through I2C at end of line.
What is the difference between the S and D strings? The same die and package with two different default register images. The parameters that matter, start current and commutation timing, still come from the EEPROM, so the difference is in the defaults a blank part starts with.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.