Contact Us

DAC128S085CIMTX-NOPB

Brand: Texas Instruments
Texas Instruments DAC128S085CIMTX-NOPB is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DAC128S085CIMTX-NOPB — Power Management & Signal Chain | Superb Automation

DAC128S085CIMTX-NOPB

Texas Instruments — Power Management & Signal Chain

Product Overview

The DAC128S085CIMTX-NOPB from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DAC128S085CIMTX-NOPB: the octal 12-bit converter in the 16 pin TSSOP

The DAC128S085CIMTX-NOPB is an eight channel, 12 bit voltage output converter in a sixteen pin TSSOP, packed 2500 pieces on a large tape and reel. The vendor carries the family as ACTIVE and describes a single supply of 2.7 V to 5.5 V, a rail to rail output, ensured monotonicity, a four wire serial interface that runs to 40 MHz, two independent reference inputs that each serve four channels, a power on reset to zero scale, and an operating range of minus 40 to plus 125 degrees. Typical supply power is 1.95 milliwatts at 3 V and 4.85 milliwatts at 5 V.

Two features separate this part from the single reference octals that sit around it. The first is the pair of reference pins, one for channels A to D and one for channels E to H, each settable between 0.5 V and the analogue supply, which lets one group of four channels span 0 to 2.5 V while the other spans 0 to 4.096 V on the same die. The second is the daisy chain, which allows an unlimited number of these devices to be updated through one serial port, and that is the feature that decides whether an eight channel part becomes a sixteen or twenty four channel system without a second chip select line per device.

The DAC128S085CIMTX-NOPB rows as the addendum publishes them

Part classOctal 12 bit voltage output converter, one reference pair
Vendor statusACTIVE, production data
Data sheetSNAS407H, August 2007, revised April 2015
Supply range2.7 V to 5.5 V, single supply
Resolution12 bits, eight channels
Integral nonlinearity8 LSB maximum
Differential nonlinearity0.75 LSB and minus 0.4 LSB maximum, monotonic
Settling time8.5 microseconds maximum to half scale
Zero code error15 mV maximum
Full scale errorminus 0.75 per cent of full scale range maximum
Reference range0.5 V to the analogue supply, two pins
InterfaceThree wire serial, clock to 40 MHz over the full supply range
Input register16 bit shift register, daisy chain capable
Power on resetOutputs to zero scale, held until a valid write
Power, 3 V1.95 milliwatts typical
Power, 5 V4.85 milliwatts typical
Power down, 3 V0.3 microwatts typical
Power down, 5 V1 microwatt typical
Body, TSSOP16 pins, 5.00 by 4.40 millimetres
Body, WQFN16 pins, 4.00 by 4.00 millimetres
Reel row, TSSOPDAC128S085CIMTX/NOPB, 2500 pieces, large tape and reel
Tube row, TSSOPDAC128S085CIMT/NOPB, 92 pieces, tube
Reel row, WQFNDAC128S085CISQX/NOPB, 4500 pieces, large tape and reel
MarkingX78C on the TSSOP, 128S085 on the WQFN
Moisture levelLevel 1 at 260 degrees, unlimited floor life
TemperatureMinus 40 to plus 125 degrees

The packing rows are the ones to read twice. The TSSOP reel is 2500 pieces and the WQFN reel is 4500, so a production quantity quoted in reels is not a production quantity quoted in parts until the body is named. The WQFN also has a 1000 piece small reel row under the same base string, which is the packing a prototype order usually receives, and a line that expects 4500 and gets 1000 has a schedule problem rather than a part problem.

What the electrical table fixes

The 8 LSB integral nonlinearity is quoted over the full temperature range and it is generous for a 12 bit part, which is the trade the part makes for eight channels in one body. At a 4.096 V reference one LSB is 1 mV and 8 LSB is 8 mV, so a channel that is asked to hold a set point to better than 10 mV across temperature is inside the specification by a narrow margin and should be checked against the zero code and full scale errors as well. Zero code is 15 mV maximum and full scale error is minus 0.75 per cent of range, which at 4.096 V is about 30 mV.

The settling time of 8.5 microseconds is quoted to half scale and it is the figure that sets the update rate when the part drives a multiplexer or a sample and hold stage. Eight channels updated in sequence at 8.5 microseconds each is 68 microseconds for a full sweep, about 14.7 thousand full sweeps per second, and that is the number a control loop should be sized against rather than the 40 MHz clock. The clock rate sets how fast a register can be loaded, not how fast the output moves.

The 40 MHz interface figure is quoted across the whole supply range, which is unusual and worth noting because many octal converters drop to 25 MHz below 3.6 V. The 16 bit frame means a single channel update is one frame and an eight channel update is eight frames, and the daisy chain mode turns that into one long frame per device in the chain. The part returns no data on the serial line, so a system that needs to read back a register has to keep its own copy, and that is the difference between this device and the converters that carry a readback bit.

Where the body fits on a board

The WQFN at 4.00 by 4.00 millimetres is the smaller of the two bodies and the vendor calls it the smallest octal converter in its class, which is a claim about the die plus the package rather than about the pin count. The TSSOP at 5.00 by 4.40 millimetres is easier to inspect and easier to rework, and on a board that will be built in hundreds rather than in tens of thousands the TSSOP is usually the better choice for the first article. Both bodies carry the same pin functions and the same register map, so a change between them is a footprint change and nothing else.

Two references mean two decoupling networks and two reference sources, and the second source is the part that is usually forgotten. A board that ties both reference pins to one 4.096 V source gets eight channels with the same span, which is fine, but the source then has to supply the reference current for all eight channels and its output impedance appears in the settling time of every channel. The vendor gives the reference input range as 0.5 V to the supply and no reference current figure on the first page, so the current has to come from the electrical table before a reference is chosen.

What the documents do not publish

The product page gives one settling figure to half scale and no figure for a full scale step, which is the larger of the two and the one that matters when a channel has to move from zero to full range between two conversions. It gives no output noise figure and no crosstalk figure between channels on the same reference pair, and those are the numbers a customer needs when eight channels drive eight separate transmitters that must not modulate each other.

The page also gives no output amplifier drive limit beyond the rail to rail description. A converter that swings to the rails into a high impedance load may not swing to the rails into 2 kilohms, and the load at which the output stays within a stated error is a data sheet table rather than a feature line. A customer who is driving a 1 kilohm input stage should read that table before accepting the part, and a customer who is driving an ADC input with a 10 nanofarad capacitor should read the stability note.

Second source and long term availability

Octal 12 bit converters with two references are made by several vendors and the serial protocol is close enough between them that a cross is usually a software change rather than a board change, but the reference arrangement and the power down behaviour are not identical. The ADC DAC cross reference page sets out what we compare before a candidate is proposed, and the how to verify a drop in replacement page covers the bench checks that follow.

The part has been in production since 2007 with the current revision dated 2015, and the addendum in the document we read is dated November 2025, which is recent enough that the rows are current. Long term availability is not in question for the TSSOP body, and the WQFN body gives a second option if the TSSOP rows ever change packing. A customer who needs a ten year supply should still ask for a written statement rather than infer one from a status column.

What to send with an enquiry

Send the exact string, the body, the quantity and the date you need it. State the reference voltage for each group of four channels, because that decides whether one reference can serve all eight or whether two are needed. State the load, since the output amplifier is specified into a light load and a heavy load changes the settling time.

If the board is already built around the WQFN, say so, because the reel size and the marking both change with the body. The BOM scrubbing page explains how we reconcile the orderable rows against a build quantity before a schedule is confirmed.