Contact Us

CD4069UBE

Brand: Texas Instruments
Texas Instruments CD4069UBE is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

CD4069UBE — Power Management & Signal Chain | Superb Automation

CD4069UBE

Texas Instruments — Power Management & Signal Chain

Product Overview

The CD4069UBE from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

CD4069UBE: six unbuffered inverters in the 14-lead plastic DIP

The CD4069UBE is the plastic dual in line member of the CD4069UB family, six unbuffered inverters on the 3 V to 18 V CMOS process. The vendor describes the part as six channels of 3 V to 18 V inverters and marks it ACTIVE. The parametric table gives six channels, an output low current of 6.8 milliamps, an output high current of minus 6.8 milliamps, a maximum supply current of 150 microamps, standard CMOS input, push pull output, balanced outputs with an input clamp diode, and an operating range of minus 55 to plus 125 degrees.

The row reads Active, plastic DIP with 14 leads at 181.42 square millimetres, 25 pieces in a tube, RoHS yes with a nickel palladium gold lead finish, no moisture sensitivity level because a through-hole body is not reflow classified, minus 55 to plus 125 degrees and the marking CD4069UBE. The ceramic row CD4069UBF3A is marked not recommended for new builds, which is the vendor's phrase for a part that still ships and should not be chosen for a new board.

The CD4069UBE row as the vendor addendum publishes it

Part classHex inverter, unbuffered
Vendor descriptor6 channels, 3 V to 18 V inverters
Vendor documentSCHS054E, revised January 2019, CD4069UB
Channels6, inverting, unbuffered
Supply range3 V to 18 V, with 5 V, 10 V and 15 V parametric ratings
Output low current6.8 milliamps maximum
Output high currentMinus 6.8 milliamps maximum
Supply current150 microamps maximum
Propagation delay30 nanoseconds at 10 V, typical, both edges
Input current1 microamp maximum at 18 V over temperature, 100 nA at 25 degrees
Quiescent currentTested at 20 V on every unit
Input protectionInput clamp diode
Package for this codePDIP (N), 14 leads, 181.42 square millimetres
Packing25 pieces in a tube
StatusActive, production
Part markingCD4069UBE
Same string in the addendumCD4069UBE.A, 25 piece tube
SOIC reel rowCD4069UBM96, 2500 pieces, marking CD4069UBM
SOP reel rowCD4069UBNSR, 2000 pieces
TSSOP reel rowCD4069UBPWR, 2000 pieces, marking CM069UB
Obsolete rowsCD4069UBMT and CD4069UBPW
NRND ceramic rowCD4069UBF3A, not recommended for new builds

Symmetric drive and why an inverter is not just logic

Six point eight milliamps in both directions is a symmetric output, which is the opposite of the CD4049UB and its 18 milliamps of sink against 3.1 milliamps of source. The symmetric part is the one to use when the output has to charge and discharge a capacitance at speed, because the rise and fall times match and the duty cycle of a clock stays near 50 per cent. The asymmetric part is the one to use when the load is a TTL input that only sinks.

The 30 nanosecond propagation delay at 10 V is a typical figure, and it is the same for both edges. That symmetry is what makes the part usable as an oscillator: three inverters in a ring with a resistor and a capacitor produce a square wave whose frequency is set by the passive parts, and a buffered inverter with a sharp threshold would produce the same waveform at a different frequency and with less stability. The unbuffered output is the reason this family exists alongside the buffered CD4049B.

The input clamp diode and the slow edge

An unbuffered inverter has a soft transfer characteristic, so an input that sits near the threshold draws current and both output devices conduct. That is what gives the part its linear gain, and it is also what makes a slowly changing input a power dissipation problem. The input clamp diode protects the gate from a signal that rises above the supply, which is the property that keeps the part alive on a board where a signal arrives before the rail does.

A circuit that drives this part from a sensor with a slow output should accept the extra supply current, or add hysteresis with a second inverter and a feedback resistor. A circuit that drives it from a clean logic edge sees none of that, and the 150 microamp maximum supply current applies to the quiescent case rather than to a gate held mid rail.

Where a hex inverter in a plastic DIP still makes sense

Six inverters in one 14-lead body cover a clock buffer, a level shifter, a ring oscillator, a Schmitt trigger built from two stages, and a driver for a small load, all in one part. On a board that is through-hole by necessity, that is the cheapest way to get six functions. On a board that is surface mount, the same die is available on three reels and the DIP only appears as a repair part.

The body is 181.42 square millimetres at 19.3 by 9.4 millimetres, and the tube of 25 is one build for a small instrument. A board that needs the part in a socket, or a test fixture that needs to swap an inverter, is the case where the through-hole format is the right answer rather than a legacy compromise.

The input clamp diode is worth a second look on a board that is hot plugged. A signal present before the supply rail rises is a common condition on a card that slides into a live backplane, and a CMOS gate without a clamp conducts through its input protection in an uncontrolled way. The diode gives that current a defined path, and the 1 microamp maximum input current at 18 V over temperature is the figure that shows how little the gate draws when the diode is not conducting.

The oscillator and the divider chain

The classic use of an unbuffered inverter is the RC oscillator: two inverters in a loop with a resistor and a capacitor, or three for a more stable configuration. The unbuffered transfer gives the loop a gain that varies smoothly with the input, which is what allows the oscillation to start and settle rather than latch. A buffered inverter in the same circuit oscillates at a frequency set more by the propagation delay than by the passive parts, which is why the CD4069UB exists.

The same part is used to invert a clock before it reaches a counter, to build a one shot from two gates, and to buffer a signal that has to travel across a board. Six gates in one package means a board can do all of those with one part number and no spare gate wasted.

Availability and the rows that close first

The plastic DIP and its .A row are Active at 25 pieces, the SOIC reel is Active at 2500, the SOP reel at 2000 and the TSSOP reel at 2000. The obsolete rows are the SOIC tube and the TSSOP tube, which is the same pattern as the rest of the CD4000B shelf: the reels survive and the tubes close. The ceramic row is marked not recommended for new builds, which leaves the plastic bodies as the live formats.

For a customer planning a long build, the last time buy and LTB planning page covers how to size a final order, and the date code management page covers how the stock is rotated. The pin to pin cross reference page lists the bodies that share the 14-lead pinout, which is the route for a board that has to move off the through-hole part and onto one of the three reel formats.

What to send with an enquiry

Send the string, the supply rail, whether the part is used as a logic gate or as an oscillator, and the annual quantity. The oscillator use is worth stating because it decides whether the unbuffered part is required rather than merely preferred, and a buffered substitute would change the frequency behaviour. If the board is through-hole and socketed, the .A row is also available at the same tube size.