CD4053BPWR
Product Specifications
CD4053BPWR
Texas Instruments — Power Management & Signal Chain
Product Overview
The CD4053BPWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
CD4053BPWR: the triple changeover switch in the 16-lead TSSOP
The CD4053BPWR is the thin shrink small outline member of the CD4053B family on a 2000 piece reel. The part carries three single pole double throw analogue switches with independent control pins on one die, with on-chip logic level conversion, a 3 V to 20 V digital control range, a 125 ohm typical on resistance at 15 V, a 9 picofarad on capacitance and a 30 MHz bandwidth. The vendor marks the family ACTIVE and describes it as a 20 V, 2 to 1, three channel analogue multiplexer with logic level conversion.
The row reads Active, TSSOP body with 16 leads at 32 square millimetres, 2000 pieces on a large tape and reel, RoHS yes, nickel palladium gold finish, moisture level 1 at 260 degrees with unlimited floor life, minus 55 to plus 125 degrees and the marking CM053B. Three TSSOP reel suffixes are obsolete, BPW, BPWRG3 and BPWRG4, which leaves this row and its .A partner as the published thin body formats.
The CD4053BPWR row as the vendor addendum publishes it
| Part class | Triple 2 to 1 analogue switch with independent controls |
| Vendor document | SCHS047O, revised May 2026, CD4051B, CD4052B and CD4053B |
| Package for this code | TSSOP (PW), 16 leads, 32 square millimetres at 5 by 6.4 mm |
| Packing | 2000 pieces on a large tape and reel |
| Status | Active, production |
| RoHS | Yes |
| Lead finish | NIPDAU |
| Moisture level | Level 1 at 260 degrees, unlimited floor life |
| Part marking | CM053B |
| Sibling row | CD4053BPWR.A, same quantity |
| Obsolete TSSOP rows | CD4053BPW, CD4053BPWRG3, CD4053BPWRG4 |
| SOIC reel row | CD4053BM96, 2500 pieces, marking CD4053M |
| SOP reel row | CD4053BNSR, 2000 pieces |
| PDIP row | CD4053BE, 25 pieces in a tube |
| Configuration | 2 to 1 single pole double throw, three channels |
| Single supply | 5, 12, 16 and 20 V, no 3.3 V row published |
| Dual supply | Plus or minus 2.5, 5 and 10 V |
| On resistance | 125 ohms typical at 15 V |
| Capacitance and bandwidth | 9 pF typical, 30 MHz |
| Current limit | 10 milliamps continuous per channel |
| ESD | 3000 V HBM, 2000 V CDM |
| Operating range | Minus 55 to plus 125 degrees |
The smallest body in the family and where it earns that
Thirty two square millimetres is 17 per cent of the plastic DIP body and 54 per cent of the SOIC body, and it is the package that makes a dense routing matrix possible. A card that routes eight stereo pairs through changeover switches needs sixteen switches, which is six parts of this family, and six TSSOP bodies take 192 square millimetres against 356 in SOIC. On an instrument front end where the routing sits behind a connector panel, that difference is a board that fits.
The thin body also suits a board that is already running fine pitch converters and a microcontroller, because the assembly process for 0.65 millimetre pitch is already qualified. A line that has never placed a 16-lead TSSOP should budget for a stencil aperture review and a first article before the reel is consumed.
Single supply, dual supply and the 3.3 V gap
The published single supply points for this part are 5, 12, 16 and 20 V, and the dual supply points are plus or minus 2.5, 5 and 10 V. The feature list gives a 3 V to 20 V single supply range with a caution that performance degrades below 3 V, so a 3.3 V rail is inside the coarse range and outside the characterised points. A board that needs a guaranteed on resistance figure at 3.3 V has to measure it on the actual part.
That gap is the reason a 3.3 V board sometimes ends up on a CD4052B for a function that only needs a 2 to 1 changeover: the parametric row is published there and not here. On a board that runs plus or minus 5 V instead, the dual supply row is published and the point is moot, which is the more common case for this family in instrumentation. A board that runs a single 5 V rail sits inside the published single supply row without any need for a measurement of its own. It is a documentation difference rather than a die difference, and the answer for a specific project depends on whether the qualification needs a published number or a measured one.
Control pins and the three switch independence
Three control pins, one per switch, each accepting 3 V to 20 V. That is the interface a microcontroller drives directly, and it is also the reason a board with several parts needs as many control lines as switches. A board that wants to save control lines takes the 4052B with its shared address pair and accepts that both channels move together; a circuit that needs independent throws pays for them in pins.
The three common pins are the changeover poles. Each one connects to either throw A or throw B depending on its control pin, and the part makes before it breaks nowhere: the sequence is break before make, so the pole is briefly open on every change. On a routing application that is the desired behaviour. On a circuit that expects a continuous path, it is a glitch that has to be absorbed by a capacitor or by a downstream stage that can tolerate it. The open interval is short enough that a 100 nanofarad capacitor on the pole holds a high impedance node steady, and long enough that a low impedance node with no capacitance shows a step. That is why the same part is a clean router in one circuit and a noise source in another.
Mechanical notes for a 0.65 millimetre pitch body
The 16-lead TSSOP body is 5 by 6.4 millimetres with a 0.65 millimetre lead pitch and a body thickness of about one millimetre. On a board with 0402 passives and a fine pitch converter, that is the same process window as the rest of the card and needs no special handling. On a card that otherwise carries only 1.27 millimetre parts, it needs a stencil with a thinner foil and an aperture that releases paste without bridging between adjacent leads.
The rework side matters more than the assembly side. A hot air station that lifts a 16-lead TSSOP needs a nozzle that heats the whole body evenly, and a hand that does not drag the part while the solder is liquid. A board that is repaired in the field rather than in a workshop should probably keep the SOIC body for that reason alone, even though it costs 27 extra square millimetres.
Where the reel fits a production plan
Two thousand pieces against a build of 500 leaves 1500 on the reel, which is a stock item rather than a remnant. Against a build of 3000 it is one and a half reels, which is a scheduling question rather than a stock one. The safety stock planning page sets out how that arithmetic is done against a lead time that moves, and the kitting service page covers how a partial reel is labelled and reissued.
A product with a long life should also plan for the day the reel row closes. The family has already lost five surface mount rows, and the component obsolescence management page explains how a monitoring routine catches the next one before a build is committed.
What to send with an enquiry
Send the rails, the number of switches in use, whether the three throws need independent control and the annual quantity. If the board runs 3.3 V, say so, because the published single supply row starts at 5 V and the answer may name a different part. If the drawing names the obsolete TSSOP tube, the reel is the live format and the quantity quoted has to be a reel quantity.