Contact Us

CD4049UBE

Brand: Texas Instruments
Texas Instruments CD4049UBE is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

CD4049UBE — Power Management & Signal Chain | Superb Automation

CD4049UBE

Texas Instruments — Power Management & Signal Chain

Product Overview

The CD4049UBE from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

CD4049UBE: six inverting buffers in the 16-lead plastic DIP

The CD4049UBE is the plastic dual in line member of the CD4049UB family, six inverting buffers with unbuffered outputs on the 3 V to 18 V CMOS process. The vendor describes the part in one line as six channels of 3 V to 18 V inverters and marks it ACTIVE. The parametric table gives six channels, an output low current of 18 milliamps, an output high current of minus 3.1 milliamps, a maximum supply current of 600 microamps, standard CMOS input, push pull output, over-voltage tolerant inputs and an operating range of minus 55 to plus 125 degrees.

The property that separates this part from a plain hex inverter is the input. The vendor states that the input signal high level can exceed the supply voltage when the part is used for logic level conversion, which is why the family exists: it converts a CMOS level down to a DTL or TTL level on a single supply and drives two DTL or TTL loads directly. The unbuffered output is the second difference, and it is the reason the part is chosen as a linear amplifier or a crystal oscillator stage rather than only as a logic gate.

The CD4049UBE row as the vendor addendum publishes it

Part classHex inverting buffer and level converter, unbuffered
Vendor descriptor6 channels, 3 V to 18 V inverters
Vendor documentSCHS046L, revised February 2026, CD4049UB and CD4050B
Channels6, inverting, unbuffered
Supply range3 V to 18 V, with 5 V, 10 V and 15 V parametric ratings
Input toleranceInput high level may exceed the supply voltage
Output low current18 mA maximum, enough for two DTL or TTL loads
Output high currentMinus 3.1 mA maximum
Supply current600 microamps maximum
Input current1 microamp maximum at 18 V over temperature, 100 nA at 25 degrees
Quiescent currentTested at 20 V on every unit
Package for this codePDIP (N), 16 leads, 181.42 square millimetres
Packing25 pieces in a tube
Lead finishNIPDAU
Moisture levelNot applicable for this package type
StatusActive, production
Part markingCD4049UBE
Same string in the addendumCD4049UBE.A and CD4049UBEE4, both 25 piece tube
SOIC rowsCD4049UBDR 2500 piece reel, CD4049UBDW 40 piece tube
Obsolete SOIC rowsCD4049UBD and CD4049UBDT, quantity blank, Call TI
Obsolete TSSOP rowCD4049UBPW, quantity blank, Call TI
Non-inverting siblingCD4050B, same die family, same pin count

The sink current is the number to size the load against

Eighteen milliamps of sink current against 3.1 milliamps of source current is an asymmetric output, and the asymmetry is deliberate. The N channel device is the one that has to pull a TTL input low, and TTL inputs source current out of the driving gate, so a buffer that has to drive two TTL loads needs sink capability and very little source capability. A circuit that expects the same drive in both directions is looking at the wrong part and should be reading the CD4050B or a push pull buffer with a symmetric output.

The input tolerance is the other half of the story. Because the input high level may exceed the supply, a 3.3 V logic signal can drive a buffer powered from 5 V, or a 5 V signal can drive a buffer powered from 3.3 V, without a level shifter in between. The vendor intends the part for CMOS to DTL or TTL conversion, and the maximum input current of 1 microamp at 18 V over the full range means the driving source sees almost no load. That is what makes the part usable directly on a high impedance sensor line without a buffer amplifier ahead of it.

Unbuffered outputs and what they change

An unbuffered inverter is three transistors rather than a chain of stages, so it has a lower propagation delay and a much softer transfer characteristic. The soft transfer is what makes the part usable as a small signal amplifier: a single stage biased at its threshold gives voltage gain, and two or three stages in a row give a clean square wave from a sine input. A buffered inverter has a sharp threshold and no linear region, which is the right choice for a logic gate and the wrong one for an oscillator.

The same property costs noise margin. An unbuffered gate has a narrower region where the output is defined, so a slow input edge spends longer in the transition and the supply current rises during that time. At 5 V with a 100 kHz signal the effect is small; at 15 V with a slow RC edge it becomes the dominant supply current. The vendor's 600 microamp maximum supply current figure is a quiescent figure and does not cover a gate held mid rail.

Package choice across the family

The through-hole body is 181.42 square millimetres, the SOIC D body 59.4 square millimetres, the SOIC DW body 106.09 square millimetres, the SOP NS body 79.56 square millimetres and the TSSOP PW body 32 square millimetres. The 16-lead count is what forces the choice: a hex buffer needs 16 pins because the supply takes two of them, and the small TSSOP body is the only one that gets close to the area of a 14-lead logic part.

The DW body is the wide SOIC, which is the row to look at when a board has to dissipate more than the narrow body allows or when the existing footprint is the wide one. The tube rows CD4049UBD and CD4049UBDT are both obsolete, and the TSSOP tube row CD4049UBPW is obsolete as well, so the surface mount formats that remain are the SW reels and the 40 piece DW tube.

Where this part is still the right answer

Level conversion on a mixed 5 V and 12 V board, a crystal oscillator stage in a timer, a line receiver with a high impedance input, and a lamp or relay driver that needs 18 milliamps of sink: those four jobs are still done by this family because a modern replacement either needs a second supply rail or cannot tolerate an input above its own supply. The military drawing rows on the same addendum, JM38510 and M38510 parts in the ceramic body, show how long the part has been in that role. The input clamp diode in the parametric list is what allows a signal to be present while the buffer is unpowered without the die conducting, which is the property that keeps the part on boards that are hot plugged.

The tube of 25 is the smallest quantity the plastic body ships in, so a repair line that needs six pieces takes a tube and holds nineteen on the shelf. That is the right trade for a legacy instrument and the wrong one for a pilot build, where a partial reel of the SOIC body is cheaper per piece once the handling is counted. Both routes exist because the family kept its through-hole row while dropping the TSSOP tube, which is the reverse of what usually happens to a part of this age, and it means a through-hole customer is not the one facing a last time buy.

A buyer holding a drawing that names the E body usually wants a tube for a repair line or a socketed instrument. The defense grade components page covers the ceramic and military drawing routes, the pin to pin cross reference page covers the switch to a surface mount body when the board allows it, and the drop in replacement verification page sets out the tests that separate a true drop in part from one that only shares the pin count. That page begins with the pinout and the supply range before it moves to the drive current, because those two decide whether the part can be fitted at all.