CC1101RGPR
Product Specifications
CC1101RGPR
Texas Instruments — Power Management & Signal Chain
Product Overview
The CC1101RGPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
CC1101RGPR low power sub 1 GHz transceiver in the 20 pin QFN body
The CC1101RGPR is a sub 1 GHz radio transceiver rather than a system on chip. It has no core and no flash; it has a modem, a packet handler, two 64 byte FIFOs and an SPI port, and it expects a microcontroller beside it. That makes it the right part for a product that already has a processor and needs a long range link in the 315, 433, 868 or 915 MHz bands, where the physics gives far more range than 2.4 GHz at the same power.
The receive sensitivity is the reason this family persists. Minus 116 dBm at 0.6 kBaud on 433 MHz and minus 112 dBm at 1.2 kBaud on 868 MHz, against a maximum output of plus 12 dBm, give a link budget above 125 dB. No 2.4 GHz part in the same price class comes close, because the lower frequency loses less to free space and to walls. A metering product that has to reach a basement reads that budget as the difference between one gateway and three.
Key parameters taken from the CC1101RGPR document
| Bands | 315, 433, 868 and 915 MHz industrial and short range bands, programmable over 300 to 348 MHz, 387 to 464 MHz and 779 to 928 MHz |
| Sensitivity | Minus 116 dBm at 0.6 kBaud on 433 MHz, minus 112 dBm at 1.2 kBaud on 868 MHz |
| Output power | Up to plus 12 dBm, programmable, with a range extender option for higher power |
| Data rate | Programmable from 0.6 kBaud to 600 kBaud, with modulation formats including frequency shift keying, Gaussian shaped keying, amplitude shift keying and offset keying |
| Buffers | Separate 64 byte receive and transmit FIFOs, so the microcontroller does not service every byte |
| Packet handling | Hardware support for preamble, sync word, address filtering, variable length packets, clear channel assessment and automatic checksum |
| Interfaces | Four wire SPI for configuration and data, with a digital received signal strength output |
| Low power | Wake on radio with automatic duty cycling, which lets the receiver listen for a fraction of each period |
| Supply | 1.8 V to 3.6 V, absolute maximum 3.9 V on the supply pins |
| Current | About 34 mA transmitting at plus 12 dBm on 868 MHz, and about 30 mA at plus 10 dBm |
| Body | QFN RGP 20 pins |
| Order code facts | CC1101RGPR, 3000 pieces on a large reel, moisture level 3 with a 168 hour floor life, marking CC1101, with a 92 piece tube row as CC1101RGP |
| Range option | The CC1190 range extender covers 850 to 950 MHz and pairs with this part when more output power and better sensitivity are needed |
The table above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for the first article.
Where the numbers matter in a real build
The antenna is the hard part of a sub 1 GHz product, not the radio. At 433 MHz a quarter wave is about 17 cm, which does not fit in a small enclosure, so most products use a shortened antenna with a matching network and accept the loss. At 868 MHz the same antenna is 8 cm, which is easier, and at 2.4 GHz it is 3 cm, which is why the higher band wins on size and loses on range. The choice of band is a mechanical decision before it is an electrical one, and it has to be made with the enclosure in hand.
The 0.6 kBaud rate is what buys the sensitivity, and it also sets the latency. A 64 byte packet at 0.6 kBaud takes almost a second to send, which is fine for a meter reading every fifteen minutes and impossible for a control loop. The practical range for a sensor network sits between 1.2 and 38.4 kBaud, where the sensitivity is still near the printed figure and a packet takes tens of milliseconds. A product that quotes the 0.6 kBaud sensitivity in its specification while running at 100 kBaud is quoting a number it does not get.
Wake on radio is the feature that makes a battery receiver practical. The part can wake, listen for a preamble, and go back to sleep without the microcontroller leaving its low power state, which brings the average receive current from tens of milliamps to tens of microamps. A product that has to be reachable at any time uses that mode, and a product that only transmits does not need it. The difference in the current budget is two orders of magnitude, and it is the reason this family is still selected for meters and alarms.
The 20 pin QFN body and the SPI interface make this part easy to add to an existing board, which is both its strength and its risk. The risk is that the radio is treated as a peripheral and the supply, the ground and the antenna are treated as details. A sub 1 GHz transmitter at plus 12 dBm draws 34 mA in bursts, and a ground plane with a gap under the matching network turns that burst into a spurious emission that fails the regulatory test. The reference boards are worth following closely, including the ground vias.
- Sensitivity at the data rate the product actually runs, not at the slowest rate the part supports.
- Output power and harmonic levels at the antenna connector, against the regulatory limit for the band.
- Antenna matching with the enclosure fitted, measured with a network analyser rather than assumed.
- Average current in the wake on radio duty cycle, over a full listening period.
- Packet error rate at the target distance, with the real interferers present in the band.
- Supply decoupling at the burst current, checked on the assembled board.
Which projects this part fits
This part fits utility metering, wireless sensor networks, alarm and security systems, home and building automation, industrial monitoring and wireless M bus products. It also appears in long range telemetry for agriculture and in logistics where a 2.4 GHz link does not have the reach. For customers with a product already on this family, the practical questions are the antenna and the regulatory file rather than the radio itself, and for a new product the comparison is against a system on chip that integrates the microcontroller at a similar total cost.
Questions that come up before a purchase order is released
Does this part include a microcontroller?
No. It is a transceiver with an SPI interface, so a microcontroller is required. That is an advantage in a product that already has one and a disadvantage in a product that does not, because the system on chip members of the same family integrate a core and a smaller radio block. The choice is about whether the application processor is already there.
Why is the 433 MHz band better for range than 868 MHz?
Because free space loss rises with frequency, and building penetration falls with it. At 433 MHz the same power reaches about twice as far through a wall as at 868 MHz, and both reach much further than 2.4 GHz. The trade is antenna size and, in some countries, duty cycle limits on the band, so a product sold across regions has to plan for the strictest rule it will meet.
What is the difference between the tube and the reel code?
The RGP suffix without an R is the 92 piece tube, and the RGPR is the 3000 piece large reel. The die is the same. A prototype build takes the tube, and a production build takes the reel. We keep both in view because a first build of 50 boards should not force a full reel purchase.
Can the output power be raised above 12 dBm?
Not from this part. The CC1190 range extender is the vendor answer, and it pairs with this transceiver in the 850 to 950 MHz range to deliver more output and better sensitivity. It is a separate part with its own supply and matching, and it is the right route when the link budget is short by ten decibels rather than by two.
How is the part tested at incoming inspection?
The practical checks are supply current in receive and in transmit, SPI communication with a known register write and read back, and a carrier at a known frequency measured on a spectrum analyser. A radio that has been damaged in handling usually fails the current check or the register read, and both are quick. A full sensitivity measurement belongs to a qualification sample rather than to every lot.
How SUPERB handles this line
We supply the CC1101RGPR from original reels with lot traceability and keep the tube row for prototypes. The RF component sourcing page lists the sub 1 GHz and 2.4 GHz families we carry, RF procurement covers how we plan a radio line across a multi year schedule, and obsolete RF part replacement is the page we open when a radio in an installed product reaches end of life and the firmware cannot change.