CC0402KRX5R7BB105
Product Specifications
CC0402KRX5R7BB105
Texas Instruments — Power Management & Signal Chain
Product Overview
The CC0402KRX5R7BB105 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
CC0402KRX5R7BB105: 0402 X5R 1 microfarad 16 V multilayer ceramic capacitor
CC0402KRX5R7BB105 is a general purpose multilayer ceramic chip capacitor in a 0402 body of 2 pins. The part is a 1 microfarad X5R chip capacitor in an 0402 case, rated 16 VDC at 10 percent tolerance, 0.5 mm thick, taped in 10000 piece reels and rated from minus 55 to plus 85 degrees Celsius.
Order code and package
| Order code | CC0402KRX5R7BB105 |
| Case | 0402, 1005 metric, 1.0 by 0.5 by 0.5 mm |
| Capacitance | 1 microfarad |
| Tolerance | plus or minus 10 percent |
| Rated voltage | 16 VDC |
| Dielectric | X5R |
| Temperature range | minus 55 to plus 85 degrees Celsius |
| Termination | tin, halogen free, RoHS |
| Moisture level | MSL 1 |
| Reel quantity | 10000 pieces |
Electrical parameters that decide the application
| Dissipation factor | 10 percent maximum |
| Insulation resistance | 50 megohm minimum |
| Endurance test voltage | 150 percent of rated voltage |
| Style | SMD chip |
| Leakage at 16 V | 320 nA from the insulation resistance |
| Endurance rating | life test, not a working voltage |
Points to check before this part goes on a BOM
X5R stops at plus 85 degrees Celsius. A board that runs at 105 degrees ambient is outside the dielectric rating even though the capacitor will still measure capacitance on the bench, and the failure mode is a slow loss of value with temperature rather than an open circuit. The X7R part in the same 0402 case is the substitution when the ambient goes above 85.
Fifty megohms at 16 V is 320 nA of leakage. On a rail that is expected to hold charge for weeks, ten of these capacitors leak 3.2 microamps, which is 28 mAh over a year and larger than the standby current of many of the products they are fitted to.
The dissipation factor of 10 percent is quoted at one frequency and turns into 15.9 ohms of equivalent series resistance at 1 kHz for a 1 microfarad part. That is not a decoupling capacitor at kilohertz, and the value only becomes useful in the hundreds of kilohertz where the impedance curve takes over. Reading the dissipation factor without the curve is how a 1 microfarad part gets chosen for a job that needs a 100 nanofarad one.
The tolerance of plus or minus 10 percent is the unbiassed figure. A 0402 1 microfarad 16 V X5R loses a large share of its capacitance at rated voltage, so the value that the board sees at 16 V is not the nameplate value, and a product that relies on 1 microfarad at 15 V has to read the bias curve for the actual case size rather than the catalogue headline.
The endurance figure of 150 percent is a life test at 24 V for this part and not an operating voltage. Boards have been specified at 24 V because the datasheet mentioned it, which puts the part 50 percent over its rating and shortens the life to whatever the test conditions allow rather than the rated life.
A 0.5 mm thick 0402 with 1 microfarad is a high capacitance density part, and the mechanical weak point is the ceramic body under board bending. Assemblies that are depanelised or screwed down after reflow see flex cracks that later turn into leakage; the soft termination version of the same series exists for exactly that, and the difference is not visible on the BOM line.
Ten thousand pieces per reel sets how often the line stops, and MSL 1 means no bake before use. Both are small things that decide whether a passive line runs at rate, and neither appears in an electrical comparison of two capacitor part numbers.
This part shares its 0402 land pattern with the 100 nanofarad X7R part in the same series. Substituting one for the other by footprint alone changes the dielectric, the voltage rating and the temperature range at once, which is the most common way a passive substitution passes incoming inspection and fails in the field.
The order string carries the whole specification: CC is the series, 0402 the case, K the 10 percent tolerance, X5R the dielectric, 7 the 16 V voltage code, BB the termination, and 105 the value in picofarads. A single mistyped digit is a different capacitor, and 104 would be 100 nanofarad rather than 1 microfarad, which is the most common transcription error in a passive line item.
There is no marking on an 0402 body, so once the reel is off the machine the part cannot be identified. Reel control and the incoming label check are the only traceability this part has, which is why a substituted reel is discovered in the field rather than at goods inwards.
The series contains a soft termination variant and an automotive variant with AEC-Q200 qualification. All three share the case size and the value, so a purchasing substitution between them changes the mechanical robustness or the qualification status without changing anything an electrical test would notice.
Where this order code fits
Bulk and mid frequency decoupling on 3.3 V and 5 V rails, coupling in audio and analogue paths, and charge storage in consumer products where the ambient stays under 85 degrees. Teams comparing it with a neighbouring part start from our BOM Shortage Recovery page, and teams replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.
Questions buyers ask
Can this replace a 1 microfarad 0402 X7R part? Only if the ambient stays below 85 degrees and the capacitance at the working voltage is enough. The case and the value match, the dielectric and the temperature range do not, so the substitution is a decision about the product and not about the footprint.
What is the leakage of one part? 320 nA at 16 V from the 50 megohm insulation resistance, which rises with temperature and is quoted at the rated voltage rather than at the rail the part actually sits on.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Incoming Inspection Plan page sets out the checks that keep a substitute from failing on the bench.