Contact Us

BQ7694203PFBR

Brand: Texas Instruments
Texas Instruments BQ7694203PFBR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

BQ7694203PFBR — Power Management & Signal Chain | Superb Automation

BQ7694203PFBR

Texas Instruments — Power Management & Signal Chain

Product Overview

The BQ7694203PFBR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

BQ7694203PFBR battery monitor and protector for three to ten series packs

The BQ7694203PFBR is the monitoring and protection front end for packs of three to ten series cells using lithium ion, lithium polymer or lithium iron phosphate chemistry. It measures every cell, measures pack current through an external shunt, drives high side N-channel protection FETs from an internal charge pump, and runs a configurable protection set that can act on its own or wait for a host. The whole device sits in a 48 pin TQFP measuring 7 mm by 7 mm.

Two things separate this part from the older front ends. It measures cell voltage to better than 10 mV typical and current with an offset below 1 uV, which is what a state of charge estimate needs. And it can act autonomously: the protection thresholds, the FET control and the recovery behaviour live in the device, so a pack does not go unprotected when the host processor hangs. The 85 V tolerance on the cell inputs covers a ten series stack with margin.

Key parameters taken from the BQ7694203PFBR document

Cells covered3 to 10 in series
PackagePFB, 48 pin TQFP, 7 mm by 7 mm
Cell voltage accuracybetter than 10 mV typical
Current measurementplus or minus 200 mV range across the sense resistor, offset below 1 uV typical
Cell inputstolerant to 85 V, random cell attach sequence allowed
Protection FET drivehigh side N-channel with integrated charge pump, optional autonomous recovery
Supply current, normal mode286 uA typical
Supply current, sleep modes24 uA to 41 uA depending on the mode
Supply current, deep sleep9 uA to 10 uA
Supply current, shutdown1 uA
RegulatorsREG18 internal 1.8 V, plus REG1 and REG2 programmable to 1.8 V, 2.5 V, 3.0 V, 3.3 V or 5.0 V
Temperature inputsinternal sensor plus up to nine external thermistors
Interfaces400 kHz I2C, SPI and HDQ one wire
Configuration memoryone time programmable memory, programmed on the production line

The table above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for the first article.

Where the numbers matter in a real build

The current measurement range is a limit on the whole pack, not a detail. The device measures plus or minus 200 mV across the shunt, so the shunt value follows the maximum pack current: a 100 A pack needs a 2 mOhm shunt, while a 20 A pack can use 10 mOhm for a better signal. Picking the shunt to make the numbers round usually ends with either a clipped reading at peak current or a noisy reading at low current.

The power modes decide the shelf life. 286 uA in normal mode is fine while the pack is in use, but a pack that sits in a warehouse needs the sleep and deep sleep modes, which drop to 24 uA and 9 uA. Those modes are entered over the bus or by pin, and the wake sources have to be chosen deliberately, otherwise a pack will not come back from deep sleep when a charger is applied.

High side FET drive is the reason this part is chosen over low side front ends in many industrial packs. The pack negative stays continuous, so the same pack can be used with chargers and loads that share a ground with the system, and a shorted FET cannot disconnect the ground reference. The charge pump for the high side drive is internal, which removes a set of external components but also means the FET gate charge has to be checked against what the pump can supply at the switching rate the protection needs.

The one time programmable memory is programmed at the pack factory. That fixes the configuration for the life of the board, which is good for traceability and bad for anyone who wants to change a threshold in the field. Prototypes therefore usually run with register settings over the bus, and the OTP image is burned only after the pack passes qualification.

  • Autonomous protection means a host hang does not leave the pack unprotected, which is the single most common finding in pack safety reviews.
  • Nine thermistor inputs allow cell level and connector level temperature coverage without an external multiplexer.
  • The secondary chemical fuse drive gives a hard disconnect path that is independent of the FETs.
  • Cell balancing can run autonomously or under host control, so the same board serves a simple pack and a smart pack.

Which projects this part fits

This front end fits power tool packs, garden tool packs, vacuum cleaners, e-bikes, e-scooters, light electric vehicles, non military drone packs, UPS and energy storage modules from three to ten series cells. Products that need a state of charge number, a protection record and a communication interface in one device are the natural fit. Our power management cross reference lists the front ends and gauges we hold, and the drone and UAV component page covers the packs we build around this family.

Shunt choice, the OTP image and the first article list

The current channel measures plus or minus 200 mV across the shunt, so the shunt value follows the maximum pack current rather than a preferred BOM value. The table below converts the range into a maximum current for the three values that cover most packs.

ShuntFull scale current at 200 mVDissipation at full scale
1 mOhm200 A40 W
2 mOhm100 A20 W
10 mOhm20 A4 W

The last column is the reason a small pack does not simply use a large shunt. Ten milliohms gives the best signal to noise at 20 A, but it also drops 200 mV at full scale and turns that into 4 W of heat next to the cells. Two milliohms is the usual compromise for a 50 A to 100 A tool pack, and the offset below 1 uV is what makes the low current end usable at that value.

The OTP image is burned at the programming house and cannot be changed afterwards. Prototype boards therefore run on register settings written by the host at every power up, and the image is burned only after the pack has passed qualification. The first article list should include the cell voltage reading against a bench meter at three points, the current offset with no load, the high side FET drive under a real load, and the deep sleep current, which should land in the 9 uA to 10 uA window rather than the 286 uA of normal mode.

Questions that come up before a purchase order is released

Do I still need a separate gauge with this part?

Not for protection and measurement. The device reports cell voltages, pack current, temperature and accumulated charge, which is enough for a host to compute state of charge. A dedicated gauge is only needed when the product requires a certified impedance based capacity report, and then the two parts usually share the same shunt.

How is the pack configured before OTP is burned?

Registers are written over I2C or SPI at every power up while the part is in prototype mode, and the settings are then written to the OTP image once the pack passes qualification. The production fixture burns the same image on every board, so a wrong threshold in the image is repeated across the whole lot, which is why the image is verified on the first article.

What limits the number of thermistors?

The device supports up to nine external thermistors plus the internal sensor, and several of the multifunction pins can be reassigned as thermistor inputs. Using a pin for temperature means giving up its other function, so the pin map is usually decided together with the FET drive and communication choices.

How SUPERB handles this line

We supply the BQ7694203PFBR with the OTP image handled at the programming house, and we can hold the matched shunt and the high side FETs as one kit so the current path arrives with the monitor. If a pack is moving from a low side front end to this part, the FET drive, the ground reference and the charger interface all change; send the existing pack drawing and we will list what has to move. The supplier quality audit page describes the checks we run on programming houses.