Contact Us

BQ7692000PWR

Brand: Texas Instruments
Texas Instruments BQ7692000PWR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

BQ7692000PWR — Power Management & Signal Chain | Superb Automation

BQ7692000PWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The BQ7692000PWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

BQ7692000PWR analog front end for three to five series packs

The BQ7692000PWR is the five series member of a family of battery front ends that has been in production since 2013 and has not needed a code change in the field. It measures cell voltage, die temperature and an external thermistor with one ADC, measures pack current with a second ADC acting as a coulomb counter, drives the charge and discharge FETs, and balances cells with internal FETs. The host talks to it over I2C and does the thinking.

It comes in a 20 pin TSSOP measuring 6.5 mm by 4.4 mm. The bus address and the regulator output are fixed in EEPROM at the factory and selected by the order code, with 0x08 and 0x18 addresses and 2.5 V and 3.3 V outputs available across the family. Because neither can be changed afterwards, the full code has to be right on the first order, and the address and output for a given code are read from the vendor table rather than assumed from the part number prefix.

Key parameters taken from the BQ7692000PWR document

Cells covered3 to 5 in series, 18 V class packs
PackagePW, 20 pin TSSOP, 6.5 mm by 4.4 mm
Bus addressselected by the order code, 0x08 or 0x18 across the family
Regulator outputselected by the order code, 2.5 V or 3.3 V across the family
CRC on the I2C buspresent or absent depending on the order code
Cell voltage accuracyplus or minus 15 mV over 2.0 V to 5.0 V, plus or minus 25 mV over the full temperature range
Cell measurement time250 ms for the full stack
Internal balancing current0 to 50 mA per cell on this member
External cell input resistance40 ohm to 1 kOhm, 100 ohm nominal
Supply filter resistance40 ohm to 1 kOhm
Absolute maximum on the pack rail108 V on the family, well above a five series stack
Protectionovercurrent in discharge, short circuit in discharge, overvoltage, undervoltage, secondary protector fault

The table above is read from the vendor document rather than from a catalogue summary. Where the document prints a minimum and a maximum, both are kept, because the number a test station should use is the limit and not the typical.

Where the numbers matter in a real build

The balancing current on this member is much larger than on its ten and fifteen series siblings, which are limited to 5 mA per cell. 50 mA through an internal FET means heat inside the front end, so the balancing duty cycle and the board copper both matter. A pack that balances continuously at 50 mA will run warm even when the load is off, and that heat lands on the same board as the cell taps.

The I2C address being fixed at the factory is the trap in this family. Two front ends on the same bus is impossible without a bus switch, and a board that was written around address 0x18 will not talk to an 0x08 part. Purchasing by family name instead of full order code is how a lot arrives that cannot be used, and it is not detectable until the first board is powered.

The cell input resistors are part of the measurement, not just protection. The recommended 100 ohm with a 1 uF capacitor forms the filter that keeps switching noise out of a 15 mV measurement, and the resistor value also sets the current that flows into the cell tap during a fault. Boards that use 10 ohm to save space measure noisier and put more stress on the tap during a short.

There is no EEPROM programming step beyond the factory settings, and no firmware to load into the part. That is why this family survives in long life industrial products: the host code owns the policy, and the front end is a fixed function block that does not change under it.

  • Sub blocks can be turned off individually, so the host can trade measurement rate against supply current while the pack is idle.
  • SHIP mode puts the pack into an ultra low power state with a single command, which is how packs are stored before they are installed.
  • The integrated cell balancing FETs remove external bleed resistors and their control lines.
  • Random cell connection order is tolerated, which simplifies hand assembly of prototype packs.

Which projects this part fits

Three to five series packs that need a digital readout and hardware protection belong here: power tools, garden tools, e-bikes and e-scooters, battery backup units, small UPS modules and industrial instrument packs. Packs that also need a state of charge algorithm add a gauge on the same shunt. The power management cross reference covers the front ends and gauges we keep, and safety stock planning explains how a fixed address part is held as a dedicated line rather than pooled with its siblings.

How the order code fixes the bus and the regulator

This family stores the I2C address, the regulator voltage and whether the bus carries a CRC in factory EEPROM, and the order code selects the combination. The document lists members with 0x08 and 0x18 addresses, with 2.5 V and 3.3 V regulator outputs, and with and without CRC, across three cell counts and three package sizes. Because those settings cannot be changed after the part is built, the full order code has to reach the reel.

PropertySet by the order code, not by the host
Series cells3 to 5 on this member, 6 to 10 and 9 to 15 on its siblings
I2C address0x08 or 0x18, 7 bit
Regulator output2.5 V or 3.3 V
CRC on the busPresent or absent
Package20 pin TSSOP on this member, 30 and 44 pin on the larger siblings

The first article test is short but decisive: confirm the part acknowledges at the address in the pack firmware, measure the regulator output with the host load attached, check cell voltage accuracy against a bench meter at two points inside the 2.0 V to 5.0 V window, measure the balancing current on one cell, and confirm that SHIP mode drops the pack current to the specified low level. A wrong address variant fails the first item and nothing else needs to be run.

One more point on stock. Because the address is fixed, an address variant cannot cover for another, so a line that uses two addresses needs two reels and two lines on the kit list. Pooling them as one family item is how a pack line stops on a Monday morning with reels that answer at the wrong address.

Questions that come up before a purchase order is released

Can this part run the host processor directly?

The family offers 2.5 V and 3.3 V outputs, and the one fitted decides whether a low power host can run from the pack directly. The regulator current is limited, so a host with a radio or a display needs its own supply and the front end regulator is used only for the reference and the thermistor divider.

What happens if the wrong address variant arrives?

Nothing on the bus answers at the expected address, so the pack looks dead while the cells are fine. The part itself is not damaged. The only fix is to fit the correct order code, which is why we ask for the full string including the address and regulator suffix before quoting.

Is a CRC needed on the bus?

Members of the family differ here, so the code decides. Without CRC the host protects the transaction itself by reading a register back after each write; with CRC the bus frame carries a check word. Packs in high vibration or high noise environments normally choose the CRC member, and the two cannot be mixed on one bus without the host knowing which is which.

How SUPERB handles this line

We supply the BQ7692000PWR by full order code and keep the address and regulator variants as separate stock lines, because a substitution here stops a pack line. If a pack is moving from a discrete protector to this front end, the cell tap filter and the FET drive are the two areas that change; send the pack drawing and we will mark what has to be reworked. Start from the obsolete part cross reference page if the current front end is being discontinued.