Contact Us

BQ25302RTER

Brand: Texas Instruments
Texas Instruments BQ25302RTER is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

BQ25302RTER — Power Management & Signal Chain | Superb Automation

BQ25302RTER

Texas Instruments — Power Management & Signal Chain

Product Overview

The BQ25302RTER from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

BQ25302RTER: standalone 2 A buck charger for one cell in a sixteen pin WQFN

BQ25302RTER is a synchronous buck charger with the FETs and the sense elements inside, taking 4.1 V to 6.2 V in and charging a single cell at up to 2 A in a WQFN body of 16 pins. The converter switches at 1.2 MHz and reaches 94.3 per cent efficiency at 1 A from a 5 V input, which is what allows a 2 A charge from a USB port without a hot spot. The current is set by one resistor from ICHG to ground, and the pack voltage is chosen by strapping VSET rather than by a divider. The RTE body is 3.00 mm by 3.00 mm.

Order code and package

BQ25302RTERWQFN RTE, 16 pins, 3000 pieces on a large reel, NIPDAU, Level-1-260C-UNLIM
BQ25302RTER .A and .Blabel rows of the same body and reel, same finish and same moisture level
Charge voltage options4.1 V, 4.2 V, 4.35 V and 4.4 V, selected by the VSET pin
Body size3.00 mm by 3.00 mm, sixteen pins, thermal pad, two layer board supported
Absolute maximum28 V at VBUS, which is well above the 6.2 V operating ceiling
Temperaturejunction range minus 40 to plus 125 C, with thermal regulation at 120 C

Electrical parameters that decide the application

Input range4.1 V to 6.2 V operating, with 28 V of absolute maximum at the input pin
Charge voltage4.078 to 4.118 V on the 4.2 V setting, 4.100 V typical, over minus 40 to plus 85 C
Charge current10 mA to 2000 mA, set as KICHG over RICHG with KICHG of 40,000, so 23.2 kohm gives 1.72 A and 40.2 kohm gives 1.0 A
Current accuracyplus or minus 10 per cent on the charge current, plus or minus 0.5 per cent on the voltage
Precharge10 per cent of the fast charge current, below the internal low battery threshold
Termination10 per cent of the fast charge current, 172 mA at a 1.72 A setting
Leakage200 nA from the cell at 4.5 V in disable, 4 uA from VBUS with the part disabled
On resistance65 mOhm on the reverse blocking FET, 82 mOhm high side and 72 mOhm low side, all maximums
Input regulationVINDPM tracks the cell at 1.044 times the pack voltage plus an offset, with a floor at the minimum
Protectioninput undervoltage and overvoltage, pack overvoltage, thermal regulation and shutdown, and a safety timer

Family variants and how they differ

VSET against a dividerthe pack voltage is a strap option here, so the four settings are the whole range and an unusual chemistry is not supported
2 A against the 1.5 A membersthe higher current needs a 1 uH inductor and a bigger input capacitor, and the body and pinout stay the same across the family
VINDPM against a fixed input limitthe input regulation point follows the cell rather than sitting at a fixed voltage, which is what keeps a weak cable from collapsing at the end of the cycle
ICHG open against shortedboth conditions disable the charger and blink the status pin, so a resistor that lifts off the pad fails safe rather than charging at an unknown current
Battery tracking against boost modethis part does not boost, so a 5 V input charging a 4.4 V cell is near the top of its range and a lower input reduces the current it can deliver
Two layer against four layerthe vendor states that the body supports a two layer board, and the pad has to be stitched to the ground plane for the thermal path to work

Points to check before this part goes on a BOM

The input ceiling is close to a USB rail. The part regulates from 4.1 V to 6.2 V, so a 5 V port that sags to 4.4 V under load reduces the headroom to 300 mV above a 4.1 V cell. VINDPM then lowers the current to hold the input, and the charge rate falls quietly rather than failing, which is why the input capacitor and the cable resistance decide the real charge time on a 2 A product.

The current resistor is not a divider. ICHG is set as 40,000 divided by the resistor, and the pin cannot carry a capacitor. A filter capacitor on that pin, added to quiet a noisy reading, moves the current setting and in the worst case makes the part read the pin as shorted and stop. The document states this explicitly and it is the most common assembly mistake on this family.

A 10 per cent current tolerance is wide. At a 1.72 A setting the part can deliver between 1.55 A and 1.89 A, and a charge time quoted from the nominal value will be short by up to ten minutes on a large cell. Products that quote a charge time in the user manual usually take the low end of the window, which is the only figure that holds on every unit.

Termination at 10 per cent leaves capacity unused. The cycle ends at about 170 mA on a 1.72 A setting, and the cell then relaxes to a lower voltage. A gauge that reports 100 per cent at the termination point will read 95 per cent an hour later, and a product that shows the pack at 95 per cent after a full charge is usually showing this behaviour rather than a gauge fault.

The thermal loop runs at 120 C on the die. That is below the 125 C junction limit and well below the 150 C shutdown, so a board with insufficient copper does not fail, it charges slowly. The symptom is a product that charges at 2 A for a minute and then holds at 1 A, and the fix is in the copper rather than in the register.

Leakage in disable is the shelf life number. 200 nA from the cell at 4.5 V is effectively nothing, but the input side draws 4 uA while disabled, so a product left plugged into a dead adapter still drains the input capacitor and any indicator on that rail. That is small enough to ignore on most products and not small enough on a product that ships with a charged pack and sits in a warehouse.

Where the board goes wrong

The input capacitor is the part that decides whether a 2 A charge from a weak cable works. The converter draws pulses at 1.2 MHz, and a 10 uF capacitor close to the VBUS pin keeps those pulses off the cable. A part placed across the board turns the cable inductance into a resonance that trips the input regulation loop on every cycle.

The second fault is the inductor return. The pad under the body is the switch node return and the thermal path at the same time, so a pad with no vias runs hot and radiates. The vendor example puts several vias in the pad and keeps the sense traces away from it, and both are needed for the 2 A rating to be real.

What to ask a supplier for

Ask for the moisture level and the reel size. This body is published at Level 1 with unlimited floor life, which is one of its advantages, and a reel that requires a bake before use is either a different body or a part that has been re-reeled.

Ask also for the date code spread on the reel. A charge current set by one resistor depends on the internal reference, and mixing date codes from different periods on one line makes a 10 per cent current window look wider than it is when the units are measured.

Where this order code fits

Wireless speakers, barcode scanners, cradles, cordless tools and building automation nodes use this class of part because a 2 A charge from a 5 V rail needs a converter rather than a linear element. The fixed voltage options cover the four common single cell chemistries without an external divider. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Safety Stock Planning page.

Questions buyers ask

Does this part need a host to start charging? No. It is standalone, and with the resistor in place and the input present it runs the precharge, fast charge and termination sequence by itself. A host can read the status pin but does not have to write anything.

What inductor does a 2 A build need? The document gives the value and the saturation requirement, and at 1.2 MHz a 1 uH part with a saturation above the current limit is the usual choice. A part rated for exactly 2 A saturates on the first step because the peak current is above the average by half the ripple.

Why does the charger slow down near full? Two reasons. The current falls as the cell reaches regulation, which is normal, and the input regulation loop may reduce the current if the 5 V rail sags. A product that charges quickly to 80 per cent and slowly after that is behaving as intended.

Can the 4.4 V setting be used on a 4.2 V cell? No. The setting is the regulation point, and holding a 4.2 V cell at 4.4 V shortens its life and can vent it. The strap is a hardware choice made at assembly, so a mixed build on one line needs the two variants kept apart rather than selected in firmware.

Is the part protected against a reversed cell? The reverse blocking FET is integrated and stops current flowing from the cell back into the input when the input is absent, but a physically reversed cell is a different condition. The battery connector keying is what prevents that, and the part is not specified for it.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.