Contact Us

AMC1305M25DWR

Brand: Texas Instruments
Texas Instruments AMC1305M25DWR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AMC1305M25DWR — Power Management & Signal Chain | Superb Automation

AMC1305M25DWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The AMC1305M25DWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

AMC1305M25DWR isolated delta sigma modulator with a plus or minus 250 mV input and a CMOS output

The AMC1305M25DWR is a second order delta sigma modulator rather than an amplifier, and the difference shows up at the interface. It does not put an analogue voltage on the low side. It puts a one bit stream on a CMOS pin, clocked from the controller at 5 MHz to 20.1 MHz, and the controller turns that stream into a number with a digital filter. In exchange for that extra step the part delivers 16 bits of resolution and a noise shaping that no successive approximation channel matches at this signal level.

The input of the M25 member is a plus or minus 250 mV window built for a shunt, in the same range as an isolated amplifier of the same size, and the family also carries a plus or minus 50 mV member for smaller shunts. The barrier is a capacitive double barrier rated at 7000 V peak reinforced and 5000 V RMS for one minute, and the part is specified over minus 40 to plus 125 C. Everything about it is aimed at a current measurement that has to be accurate and quiet rather than merely present.

Key parameters taken from the AMC1305M25DWR document

Input full scalePlus or minus 250 mV linear range on the M25 and L25 members, plus or minus 50 mV on the M05 member
Resolution16 bits of differential nonlinearity at 0.99 LSB and integral nonlinearity of 4 LSB, with a sinc3 filter at an oversampling ratio of 256
Dynamic range85 dB and 13.8 effective bits at 78 kSPS with the digital filter set for that rate
Offset errorPlus or minus 150 microvolt maximum on the 250 mV members, plus or minus 50 microvolt on the 50 mV member
Offset driftPlus or minus 1.3 microvolt per C maximum over the full temperature range
Gain errorPlus or minus 0.3 percent maximum, with plus or minus 40 ppm per C of gain drift
Common mode rejection104 dB at direct current, with the input stage specified over its common mode window
InterfaceCMOS on the M members and LVDS on the L member, clocked from the controller
ClockModulator clock 5 MHz to 20.1 MHz, with the filter oversampling ratio setting the output rate
SuppliesHigh side 4.5 to 5.5 V at 8.2 mA maximum, low side 3.0 to 5.5 V at 4.0 to 5.5 mA depending on the rail
Isolation7000 V peak reinforced per VDE 0884-11, 5000 V RMS for one minute per UL1577, transient immunity 15 kV per microsecond
TemperatureMinus 40 to plus 125 C, fully specified
BodySOIC DW sixteen pins, wide body
Order code factsAMC1305M25DWR, 2000 pieces on a large reel, moisture level 3 with a 168 hour floor life, marking AMC1305M25, with a 40 piece tube row for prototypes

The table above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for the first article.

Where the numbers matter in a real build

The clock is not a detail the controller can pick late. The modulator needs a clock between 5 MHz and 20.1 MHz, and the same clock usually drives the digital filter, which means the sample rate, the filter latency and the resolution are all tied to one number. A 20 MHz clock with an oversampling ratio of 256 gives a 78 kSPS output, which is the point where the 85 dB dynamic range figure is quoted. Halving the clock halves the rate and buys about three decibels; doubling it costs the same and takes the rate to 156 kSPS, which is often still slow for a current loop but fast enough for a metering channel.

Compared with an isolated amplifier, the modulator trades latency for resolution and noise immunity. The filter that turns the bit stream into a number has a group delay of a few modulator cycles, so a fault that appears at the shunt is seen by the controller a few microseconds later than it would be with an analogue channel. In exchange the measurement is quieter, the channel does not need a converter with a matched reference, and the isolation barrier carries a digital signal that is far less sensitive to the common mode step of a switching bridge.

The 250 mV range sets the shunt exactly as it does for an amplifier, but the loss argument is different because the modulator can resolve smaller signals. A 0.25 milliohm shunt with a 250 mV range gives 1000 A and 250 W of loss at full scale, which is not a drive. A 1 milliohm shunt gives 250 A and 62.5 W, which is a 75 kW drive at 300 A peak with some margin. The right shunt is the one whose full scale loss the thermal file accepts, and the modulator's resolution is what lets that shunt be smaller than a converter channel would allow.

The 50 mV member of the family is the one to quote when the shunt is very small. A 0.1 milliohm shunt develops 50 mV at 500 A, and 25 W of loss at that current, which is a different thermal class of problem from the 250 mV member. Both members share a pinout and a body, and they differ in the input window, so a board can be laid out once and populated with either, provided the firmware knows which one is fitted. That is a useful hedge during a program where the shunt value is still moving.

  • Clock source and frequency, with the filter oversampling ratio and the resulting output rate written down.
  • Shunt value against the full scale loss at continuous current, with the thermal file open.
  • Offset at 25 C on the first article, measured with the inputs shorted at the shunt.
  • Common mode step response at the switching edge, with the real filter in the controller.
  • Bit stream integrity at the longest trace between the modulator and the controller pin.
  • Isolation and creepage on the assembled board, against the safety file.

Which projects this part fits

This part fits phase current measurement in motor drives and frequency inverters, solar inverter current sensing, DC to DC converter current loops, battery current measurement in energy storage and shunt based metering. It is the right choice where the controller already has a sigma delta filter peripheral, which is common on motor control processors, and where the measurement has to be quiet enough for a metering grade result. On a drive that needs a fast overcurrent trip as well, this part feeds the control loop and a separate isolated comparator feeds the trip.

Questions that come up before a purchase order is released

Can the modulator output be read without a dedicated filter peripheral?

Yes, with a software filter, but the arithmetic load is real. A sinc3 filter at an oversampling ratio of 256 needs a few hundred accumulator operations per output sample, which a 48 MHz controller can do at audio rates and struggles to do at control loop rates while running the rest of the drive. The clean answer is a processor with a sigma delta filter module, and most motor control families have one.

What is the difference between the M and L members?

The M members drive a CMOS output and the L member drives an LVDS pair. CMOS is simpler and works over a short trace on the same board. LVDS is the choice when the controller sits on a different board or when the trace is long enough that a single ended edge picks up the switching noise of the bridge. The input stage and the accuracy are the same, so the choice is about routing rather than measurement.

Why is the gain error quoted as a percentage of full scale?

Because the transfer function of a modulator is a bit density, not a voltage, and the density maps to full scale. A gain error of 0.3 percent is 0.75 mV on the 250 mV member, which is small in absolute terms and large compared with the offset. That is why the offset and the gain are calibrated separately in a production test, and why a two point calibration at end of line is the usual practice for a metering channel.

Does the part need an external clock buffer?

A short trace on the same board usually does not. A long trace, or a clock that also drives several modulators, benefits from a buffer placed close to the source, because the modulator clock input is a sampling node and a slow edge there shows up as jitter in the bit stream. The vendor reference boards show the clock routed as a controlled impedance line when more than one modulator shares it.

How is the isolation barrier handled on a two board assembly?

The barrier sits inside the package, so the two boards are separated by the part rather than by a connector. That is the reason this family is popular in drives with a separate power board: the modulator sits on the power board next to the shunt, the bit stream crosses to the control board, and there is no analogue signal crossing the isolation gap at all.

How SUPERB handles this line

We supply the AMC1305M25DWR and the other members of the family from original reels with lot traceability, and we keep the tube row for prototype quantities. The power management cross reference page lists the isolated measurement families with their controller side, ADC and DAC cross reference covers the converters and modulators we carry side by side, and pin to pin cross reference is the page for a board that has to move between the 50 mV and 250 mV members without a respin.